Morphological characterization, thermal, and mechanical properties of compatibilized high density polyethylene/polystyrene/organobentonite ternary nanocomposites
-
Farida Yahiaoui
Abstract
Composite materials made from high density polyethylene (HDPE) and polystyrene (PS) were successfully prepared in different HDPE/PS weight ratios, by melt mixing 3 wt% of bentonite clay organically modified with hexadecyl ammonium chloride (organo-modified bentonite, OBT). The structure and morphology of these composites were examined by X-ray diffraction and scanning electron microscopy. Morphological changes between the composite and the constituent materials were observed. The decrease in PS (or HDPE) particle size in HDPE/PS 70/30 (or 30/70) that blend after the OBT addition reflects a clear improvement in the HDPE/PS blend compatibility. The effect of OBT on the thermal and mechanical properties was investigated by differential scanning calorimetry, thermogravimetric analysis, and tensile measurements. The main results show a decrease in the HDPE crystallinity in the composite matrices, which reaches 25% for HDPE/PS/OBT 29/68/3 composite, also an improvement of the thermal stability, as evidenced by the higher Tonset values, and finally a reinforcement of the tensile properties as compared to the unfilled blends. Indeed, a significant enhancement of the tensile modulus (~130%) is observed for the 68/29/3 composite matrix as compared to the 70/30 unfilled blend.
References
[1] Groeninckx G, Vanneste M, Everaert V. In Polymer Blends Handbook, Utracki, LA, Ed., Kluwer Academic Publishers: Dordrecht, 2002, Vol. 1.Suche in Google Scholar
[2] Chen JH, Zhong JC, Cai YH, Su WB, Yang YB. Polymer 2007, 48, 2946–2957.10.1016/j.polymer.2007.03.037Suche in Google Scholar
[3] Cherian Z, Lehman R. Int. J. Adhes. Adhes. 2005, 25, 502–506.10.1016/j.ijadhadh.2005.02.001Suche in Google Scholar
[4] Thirtha V, Lehman R, Nosker T. Polymer 2006, 47, 5392–5401.10.1016/j.polymer.2006.05.014Suche in Google Scholar
[5] Yang LY, Smith TG, Bigio D. J. Appl. Polym. Sci. 1995, 58, 117–127.10.1002/app.1995.070580113Suche in Google Scholar
[6] Yang L, Bigio D, Smith TG. J. Appl. Polym. Sci. 1995, 58, 129–141.10.1002/app.1995.070580114Suche in Google Scholar
[7] Park CP, Clingerman GP. Plast. Eng. 1997, 97, 97–99.Suche in Google Scholar
[8] Li T, Topolkaraev VA, Hiltner A, Baer E. Adv. Chem. Ser. 1996, 252, 319–334.10.1021/ba-1996-0252.ch021Suche in Google Scholar
[9] Bratczak Z, Krasnikova NP, Galeski A. J. Appl. Polym. Sci. 1996, 62, 167–179.10.1002/(SICI)1097-4628(19961003)62:1<167::AID-APP21>3.0.CO;2-1Suche in Google Scholar
[10] Harrats C, Blacher S, Fayt R, Jerome R, Teyssie PH. J. Polym. Sci.: Part B: Polym. Phys. 1995, 33, 801–811.10.1002/polb.1995.090330509Suche in Google Scholar
[11] Barentsen WM, Heikens D, Plet P. Polymer 1974, 15, 119–122.10.1016/0032-3861(74)90012-3Suche in Google Scholar
[12] Filippone G, Salzano de Luna M. Eur. Polym. J. 2016, 79, 198–218.10.1016/j.eurpolymj.2016.02.023Suche in Google Scholar
[13] Zhang W, Lin M, Winesett A, Dhez O, Kilcoyne ALD, Ade H, Rubinstein M, Shafi KVPM, Ulman A, Gersappe D, Tenne R, Rafailovich M, Sokolov J, Frisch HL. Polym. Adv. Technol. 2011, 22, 65–71.10.1002/pat.1875Suche in Google Scholar
[14] Istrate OM, Gunning MA, Higginbotham CL, Chen B. J. Polym. Sci. Part B: Polym. Phys, 2012, 50, 431–441.10.1002/polb.23018Suche in Google Scholar
[15] Hemmati M, Fereidoon A, Shariatpanahi H, Ahangari MG, Narimani A. Polym. Plast. Technol. Eng. 2012, 51, 413–418.10.1080/03602559.2011.639837Suche in Google Scholar
[16] Yousfi M, Soulestin J, Vergnes B, Lacrampe MF, Krawczak P. Macromol. Mater. Eng. 2013, 298, 757–770.10.1002/mame.201200138Suche in Google Scholar
[17] Iyer R, Suin S, Shrivastava NK, Maiti S, Khatua BB. Polym. Plast. Technol. Eng. 2013, 52, 514–524.10.1080/03602559.2012.762024Suche in Google Scholar
[18] Sinha RS, Bousmina M. Macromol. Rapid Commun. 2005, 26, 1639–1646.10.1002/marc.200500447Suche in Google Scholar
[19] Sinha RS, Bandayopadhyay J, Bousmina M. Macromol. Mater. Eng. 2007, 292, 729–747.10.1002/mame.200700029Suche in Google Scholar
[20] Lee MH, Dan CH, Kim JH, Cha J, Kim S, Hwang Y, Lee HC. Polymer 2006, 47, 4359–4369.10.1016/j.polymer.2006.04.003Suche in Google Scholar
[21] Segal E, Tchoudakov R, Narkis M, Siegmann A, Wei Y. Sens. Actuators B Chem. 2005, 104, 140–150.10.1016/j.snb.2004.05.002Suche in Google Scholar
[22] Yoo Y, Park C, Lee SG, Choi KY, Kim DS, Lee JH. Macromol. Chem. Phys. 2005, 206, 878–884.10.1002/macp.200400526Suche in Google Scholar
[23] Wang Y, Zhang Q, Fu Q. Macromol. Rapid. Commun. 2003, 24, 231–235.10.1002/marc.200390026Suche in Google Scholar
[24] Sinha RS, Pouliot S, Bousmina M, Utracki LA. Polymer 2004, 45, 8403–8413.10.1016/j.polymer.2004.10.009Suche in Google Scholar
[25] Wu T, Yuan D, Qiu F, Chen R, Zhang G, Qu J. Polym. Test 2017, 63, 73–83.10.1016/j.polymertesting.2017.07.012Suche in Google Scholar
[26] Chen J, Chen JW, Chen HM, Yang J, Chen C, Wang Y. Compos. Part B Eng. 2013, 24, 422–430.10.4028/www.scientific.net/AMM.422.24Suche in Google Scholar
[27] Benhacine F, Yahiaoui F, Hadj-Hamou AS. J. Polym. 2014, 2014, Article ID 426470, 9 Pages.10.1155/2014/426470Suche in Google Scholar
[28] Silverstein RM, Bassler GC, Morrill TC. Spectrometric identification of organic compounds, 5th Ed., Wiley: New York, 1991, p. 430.Suche in Google Scholar
[29] Sakizci M, Alver BE, Alver O, Yorukogullari E. J. Mol. Struct. 2010, 969, 187–191.10.1016/j.molstruc.2010.02.008Suche in Google Scholar
[30] Shepherd PD, Golemba FJ, Maine FW. Clay Layers Adv. Chem. Ser. 1974, 41, 134–141.10.1021/ba-1974-0134.ch005Suche in Google Scholar
[31] Pucciariello R, Villani V, Bonini C, Auria MD, Vetere T. Polymer 2004, 45, 4159–4169.10.1016/j.polymer.2004.03.098Suche in Google Scholar
[32] Díaz MF, Barbosa SE, Capiati NJ. Polymer 2007, 48, 1058–1065.10.1016/j.polymer.2006.12.040Suche in Google Scholar
[33] Joshi J, Lehman R, Nosker TJ. Appl. Polym. Sci. 2006, 99, 2044–2051.10.1002/app.22492Suche in Google Scholar
[34] Calcagno IW, Mariani CM, Teixeira SR, Mauler RS. J. Appl. Polym. Sci. 2009, 111, 29–36.10.1002/app.28977Suche in Google Scholar
[35] Radonjic G, Musil V, Smit I. J. Appl. Polym. Sci. 1998, 69, 2625–2639.10.1002/(SICI)1097-4628(19980926)69:13<2625::AID-APP13>3.0.CO;2-TSuche in Google Scholar
[36] Wunderlich B, Thermal Analysis, Academic Press: San Diego, 1990.10.1016/B978-0-12-765605-2.50006-6Suche in Google Scholar
[37] Blyler LI, Dane JH. Polym. Eng. Sci. 1967, 7, 178–181.10.1002/pen.760070309Suche in Google Scholar
[38] Othman N, Ismail H, Mariatti M. Polym. Degrad. Stab. 2006, 91, 1761–1774.10.1016/j.polymdegradstab.2005.11.022Suche in Google Scholar
[39] Garcia M, Van Vliet G, Jain S, Schrauwen BAG, Sarkissov A, Van Zyl WE, Boukamp B. Rev. Adv. Mater. 2004, 6, 169–175.Suche in Google Scholar
[40] Bendjaouahdou C, Bensaad S. J. Vinyl Addit. Technol. 2011, 17, 48–57.10.1002/vnl.20256Suche in Google Scholar
[41] Wu D, Lin D, Zhang J, Zhou W, Zhang M, Zhang Y, Wang D, Lin B. Macromol. Chem. Phys. 2011, 212, 613–626.10.1002/macp.201000579Suche in Google Scholar
[42] Abareshi M, Zebarjad SM, Goharshadi EK. J. Compos. Mater. 2009, 43, 2821–2830.10.1177/0021998309345307Suche in Google Scholar
[43] Xue B, Li F, Sun M, Liu D, Jiang Y, Xing Y. Polym. Bull. 2011, 67, 1463–1481.10.1007/s00289-011-0466-3Suche in Google Scholar
[44] Chen B, Li X, Xu S, Tang T, Zhou B. Polymer 2002, 43, 953.10.1016/S0032-3861(01)00660-7Suche in Google Scholar
[45] Bratczak Z, Galiski A, Pluta M. J. Appl. Polym. Sci. 2000, 76, 1746–1761.10.1002/(SICI)1097-4628(20000620)76:12<1746::AID-APP4>3.0.CO;2-OSuche in Google Scholar
[46] Varkey JT, Augustine S, Thomas S. Polym. Plast. Technol. Eng. 2000, 39, 415–435.10.1081/PPT-100100038Suche in Google Scholar
[47] Araújo EM, Mélo TJA, Santana LNL, Neves GA, Ferreira HC, Lira HL, Carvalho LH, Avila MM Jr, Pontes MKG, Araújo IS. Mater. Sci. Eng. B. 2004, 112, 175–178.10.1016/j.mseb.2004.05.027Suche in Google Scholar
[48] Wu Y, Zhang H, Shentu B, WengInd Z. Eng. Chem. Res. 2015, 54, 5870–5875.10.1021/acs.iecr.5b01041Suche in Google Scholar
[49] Chieng BW, Ibrahim NA, Wan Yunus WMZ. Exp. Polym. Lett. 2010, 4, 404–414.10.3144/expresspolymlett.2010.51Suche in Google Scholar
[50] Chandran N, Chandran S, Maria HJ, Thomas S. RSC Adv. 2015, 5, 86265–86273.10.1039/C5RA14352GSuche in Google Scholar
[51] Masa A, Saito H, Sakai T, Kaesaman A, Lopattananon N. J. Appl. Polym. Sci. 2017, 134, 44574.10.1002/app.44574Suche in Google Scholar
©2018 Walter de Gruyter GmbH, Berlin/Boston
Artikel in diesem Heft
- Frontmatter
- Material properties
- Structure mediation and ductility enhancement of poly(l-lactide) by random copolymer poly(d-lactide-co-ε-caprolactone)
- Morphological characterization, thermal, and mechanical properties of compatibilized high density polyethylene/polystyrene/organobentonite ternary nanocomposites
- Preparation and assembly
- Simultaneous toughening and reinforcing of cyanate ester/benzoxazine resins with improved mechanical and thermal properties by using hyperbranched polyesters
- Surface modification of Sb-SnO2/potassium titanate composite and their performance for acrylic coatings
- Poly (vinyl alcohol)/nano-diamond composite films and hydrogels prepared by gamma ray
- Engineering and processing
- Study on structures and properties of ultra-hot drawing UHMWPE fibers fabricated via dry spinning method
- Separation of CO2/CH4 and O2/N2 by polysulfone hollow fiber membranes: effects of membrane support properties and surface coating materials
- Electric field-induced alignment of MWCNTs during the processing of PP/MWCNT composites: effects on electrical, dielectric, and rheological properties
- A molecular modeling study for miscibility of polyimide/polythene mixing systems with/without compatibilizer
- Analysis and quantitative estimation of phenolic antioxidants in polypropylene packaging for fat products
- Effects of ultrasonic injection molding conditions on the plate processing characteristics of PMMA
Artikel in diesem Heft
- Frontmatter
- Material properties
- Structure mediation and ductility enhancement of poly(l-lactide) by random copolymer poly(d-lactide-co-ε-caprolactone)
- Morphological characterization, thermal, and mechanical properties of compatibilized high density polyethylene/polystyrene/organobentonite ternary nanocomposites
- Preparation and assembly
- Simultaneous toughening and reinforcing of cyanate ester/benzoxazine resins with improved mechanical and thermal properties by using hyperbranched polyesters
- Surface modification of Sb-SnO2/potassium titanate composite and their performance for acrylic coatings
- Poly (vinyl alcohol)/nano-diamond composite films and hydrogels prepared by gamma ray
- Engineering and processing
- Study on structures and properties of ultra-hot drawing UHMWPE fibers fabricated via dry spinning method
- Separation of CO2/CH4 and O2/N2 by polysulfone hollow fiber membranes: effects of membrane support properties and surface coating materials
- Electric field-induced alignment of MWCNTs during the processing of PP/MWCNT composites: effects on electrical, dielectric, and rheological properties
- A molecular modeling study for miscibility of polyimide/polythene mixing systems with/without compatibilizer
- Analysis and quantitative estimation of phenolic antioxidants in polypropylene packaging for fat products
- Effects of ultrasonic injection molding conditions on the plate processing characteristics of PMMA
