Startseite Impact fracture toughness and morphology of polypropylene/Mg(OH)2 composites
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Impact fracture toughness and morphology of polypropylene/Mg(OH)2 composites

  • Ji-Zhao Liang EMAIL logo und Feng-Jiao Li
Veröffentlicht/Copyright: 21. September 2013
Veröffentlichen auch Sie bei De Gruyter Brill
Manuskript einreichen Informationen für Autor*innen
Journal of Polymer Engineering
Aus der Zeitschrift Journal of Polymer Engineering Band 33 Heft 8

Abstract

Magnesium hydroxide [Mg(OH)2] with high flame retardant efficiency filled polypropylene (PP) composites were prepared using a twin-screw extruder. The impact fracture behavior of the composites was measured at room temperature. It was found that the toughening effect of the filler content on the PP resin was significant. The V-notched Izod impact strength of the PP/Mg(OH)2 composites showed a nonlinear increase with increase in filler weight fraction (ϕf), as ϕf was <15%, and then it decreased slightly; When ϕf was <15%, the V-notched Charpy impact strength of the PP/Mg(OH)2 composite also increased nonlinearly, then it decreased slightly. The impact fracture surface was observed by means of a scanning electronic microscope, to understand the toughening mechanisms for the composite systems.

Keywords: impact strength; morphology; polymer composite; toughening mechanism
Corresponding author: Ji-Zhao Liang, Research Division of Green Function Materials and Equipment, School of Mechanical and Automotive Engineering, South China University of Technology, Guangzhou 510640, China, e-mail:

References

[1] Liang JZ, Li RKY. J. Appl. Polym. Sci. 2000, 77, 409–417.Suche in Google Scholar

[2] Liang JZ. J. Appl. Polym. Sci. 2002, 83, 1547–1555.Suche in Google Scholar

[3] Chiu SH, Wang WK. Polymer 1998, 39, 1951–1955.10.1016/S0032-3861(97)00492-8Suche in Google Scholar

[4] Sain M, Park SH, Suhara F. Polym. Degrad. Stab. 2004, 83, 363–367.Suche in Google Scholar

[5] Lin Z, Qiu Y, Mai K. J. Appl. Polym. Sci. 2004, 91, 3899–3908.Suche in Google Scholar

[6] Hong CH, Lee YB. J. Appl. Polym. Sci. 2005, 97, 2311–2318.Suche in Google Scholar

[7] Liang JZ, Chen Y, Jiang XH. Polym.-Plast. Technol. Eng. 2012, 51, 439–445.Suche in Google Scholar

[8] Carpentier F, Bourbigot S, Le Bras M, Delobel R, Foulon M. Polym. Degrad. Stab. 2000, 69, 83–92.Suche in Google Scholar

[9] Titelman GI, Gonen Y. Polym. Degrad. Stab. 2002, 77, 345–352.Suche in Google Scholar

[10] Sangcheol K. J. Polym. Sci. 2003, 41, 936–944.Suche in Google Scholar

[11] Liu MF, Wang Q, Liu Y. Polym.-Plast. Technol. Eng. 2010, 49, 367–372.Suche in Google Scholar

[12] Liang JZ, Li RKY, Tjong SC. Polym. Eng. Sci. 2000, 40, 2105–2111.Suche in Google Scholar

[13] Liang JZ Macromol. Mater. Eng. 2002, 287, 588–591.Suche in Google Scholar

[14] Liang JZ. J. ASTM Int. 2006, 3, 1–7.Suche in Google Scholar

[15] Liang JZ. J. Mater. Sci. 2007, 42, 841–846.Suche in Google Scholar

[16] Liang JZ. Polym. Eng. Sci. 2009, 49, 1603–1607.Suche in Google Scholar

[17] Liang JZ. Polym. Bull. 2010, 65, 815–824.Suche in Google Scholar

[18] Liang JZ. Polym. Adv. Technol. 2012, 23, 1229–1233.Suche in Google Scholar

[19] Feng JQ. Performance and mechanism research of environmental protection and efficient flame retardant polypropylene composites. Master dissertation, Guangzhou: South China University of Technology, 2013.Suche in Google Scholar

Received: 2013-7-18
Accepted: 2013-8-28
Published Online: 2013-09-21
Published in Print: 2013-11-01

©2013 by Walter de Gruyter Berlin Boston

Artikel in diesem Heft

  1. Masthead
  2. Masthead
  3. Original articles
  4. Grafting of maleic anhydride on polypropylene by reactive extrusion: effect of maleic anhydride and peroxide concentrations on reaction yield and products characteristics
  5. An optical system for measuring the residence time distribution in co-rotating twin-screw extruders
  6. Effect of processing technology on the morphological, mechanical and electrical properties of conductive polymer composites
  7. Thermodynamic modeling of polyamide-6 (PA-6)/cellulose acetate (CA) blend membrane prepared via casting technique
  8. Monte Carlo simulation of ionic conductivity in polyethylene oxide
  9. Impact fracture toughness and morphology of polypropylene/Mg(OH)2 composites
  10. High impact toughness of polyamide 6/poly (vinylidene fluoride) blends induced by an ionic liquid
  11. Application of chemically-cross-linked chitosan for the removal of Reactive Black 5 and Reactive Yellow 84 dyes from aqueous solutions
  12. Flame retardation behaviors of UV-curable phosphorus-containing PU coating system
  13. Preparation and characterization of modified chitosan for in vitro controlled release of vitamin B12
  14. Surface modification of nano-alumina and its application in preparing polyacrylate water-based wood coating
https://doi.org/10.1515/polyeng-2013-0179
Schlagwörter für diesen Artikel
impact strength; morphology; polymer composite; toughening mechanism

Artikel in diesem Heft

  1. Masthead
  2. Masthead
  3. Original articles
  4. Grafting of maleic anhydride on polypropylene by reactive extrusion: effect of maleic anhydride and peroxide concentrations on reaction yield and products characteristics
  5. An optical system for measuring the residence time distribution in co-rotating twin-screw extruders
  6. Effect of processing technology on the morphological, mechanical and electrical properties of conductive polymer composites
  7. Thermodynamic modeling of polyamide-6 (PA-6)/cellulose acetate (CA) blend membrane prepared via casting technique
  8. Monte Carlo simulation of ionic conductivity in polyethylene oxide
  9. Impact fracture toughness and morphology of polypropylene/Mg(OH)2 composites
  10. High impact toughness of polyamide 6/poly (vinylidene fluoride) blends induced by an ionic liquid
  11. Application of chemically-cross-linked chitosan for the removal of Reactive Black 5 and Reactive Yellow 84 dyes from aqueous solutions
  12. Flame retardation behaviors of UV-curable phosphorus-containing PU coating system
  13. Preparation and characterization of modified chitosan for in vitro controlled release of vitamin B12
  14. Surface modification of nano-alumina and its application in preparing polyacrylate water-based wood coating
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 3.12.2025 von https://www.degruyterbrill.com/document/doi/10.1515/polyeng-2013-0179/pdf?lang=de
Button zum nach oben scrollen