Adhesive wear behavior of gas tungsten arc welded FeB-FeMo-C coatings
-
Mehmet Yaz
Mehmet Yaz, born in 1962, completed his higher education in 1986 at the Gazi University Technical Education Faculty, Machining Department. In the fall of 1996, he started his graduate studies at the Institute of Science, Department of Mechanical Education. After completing his Master’s degree in 1999, he started his Ph.D. at the Institute of Science, Department of Metallurgical Education. In 2005, he successfully completed his Ph.D. Currently, he is an Associate Professor in the field of Materials and Metallurgical Engineering.
Abstract
In this article, a gas tungsten arc welding is used as a high energy density beam to form a surface over 0.15% carbon steel with FeB, FeMo, and graphite powders. The microstructure, microhardness, and dry-sliding wear behavior of the composite coating were investigated using optical micrography, X-ray diffraction, scanning electron microscopy, and energy-dispersive X-ray spectrometry. Microstructural investigations reveal that FeB-reinforced coating exhibited a homogeneous microstructure that consists of dendrites and eutectic. A lot of types of carbide and borides were formed. MoB4, Fe2MoC, B8C, Mo2BC, MoB, Fe3Mo, Fe3B, B25C, Fe7C3, FeB, Mo2B5, and MoC were seen in coated surfaces. Graphite iron boride coatings obtained by the gas tungsten arc welding process improved the wear resistance of carbon steel.
Funding source: Firat University Scientific Research Projects Unit
Award Identifier / Grant number: Project No: 1809
About the author
Mehmet Yaz, born in 1962, completed his higher education in 1986 at the Gazi University Technical Education Faculty, Machining Department. In the fall of 1996, he started his graduate studies at the Institute of Science, Department of Mechanical Education. After completing his Master’s degree in 1999, he started his Ph.D. at the Institute of Science, Department of Metallurgical Education. In 2005, he successfully completed his Ph.D. Currently, he is an Associate Professor in the field of Materials and Metallurgical Engineering.
Acknowledgments
The author wishes to thank the Firat University Scientific Research Projects Unit.
-
Author contributions: The author has accepted responsibility for the entire content of this submitted manuscript and approved submission.
-
Research funding: This work was supported by Firat University Scientific Research Projects Unit (FUBAP) (Project No: 1809).
-
Conflict of interest statement: The author declares no conflicts of interest regarding this article.
References
[1] P. J. Modenesi, E. R. Apolinario, and I. M. Pereira, “TIG welding with single-component fluxes,” J. Mater. Process. Technol., vol. 99, nos 1–3, pp. 260–265, 2000, https://doi.org/10.1016/S0924-0136(99)00435-5.Search in Google Scholar
[2] S. Ozel, B. Kurt, I. Somunkiran, and N. Orhan, “Microstructural characteristic of NiTi coating on stainless steel by plasma transferred arc process,” Surf. Coating. Technol., vol. 202, no. 15, pp. 3633–3637, 2008, https://doi.org/10.1016/j.surfcoat.2008.01.006.Search in Google Scholar
[3] T. Teker and D. Gencdogan, “Heat affected zone and weld metal analysis of HARDOX 450 and ferritic stainless steel double sided TIG-joints,” Mater. Test., vol. 63, no. 10, pp. 923–928, 2021, https://doi.org/10.1515/mt-2021-0022.Search in Google Scholar
[4] S. O. Yılmaz, “Wear behavior of gas tungsten arc deposited FeCrC, FeCrSi, and WCo coatings on AISI 1018 steel,” Surf. Coating. Technol., vol. 194, nos 2–3, pp. 175–183, 2005, https://doi.org/10.1016/j.surfcoat.2004.08.227.Search in Google Scholar
[5] I. Kirik, Z. Balalan, A. Imak, and M. Yaz, “Properties of different TIG coatings of stellite on the Hardox 450 and St 52 steel,” Mater. Test., vol. 62, no. 11, pp. 1089–1093, 2020, https://doi.org/10.3139/120.111590.Search in Google Scholar
[6] B. Matijević and M. Stupnišek, “Novelty in diffusion coating technology,” Mater. Manuf. Process., vol. 24, nos 7–8, pp. 887–893, 2009, https://doi.org/10.1080/10426910902917710.Search in Google Scholar
[7] Z. Y. Ma, S. C. Tjong, and L. Gen, “In-situ Ti–TiB metal–matrix composite prepared by a reactive pressing process,” Scripta Mater., vol. 42, no. 4, pp. 367–373, 2000, https://doi.org/10.1016/S1359-6462(99)00354-1.Search in Google Scholar
[8] S. O. Yılmaz, M. Ozenbas, and M. Yaz, “Synthesis of TiB2-reinforced iron-based composite coating,” Tribol. Int., vol. 42, no. 8, pp. 1220–1229, 2009, https://doi.org/10.1016/j.triboint.2009.04.041.Search in Google Scholar
[9] L. Bourithis, S. Papaefthymiou, and G. D. Papadimitriou, “Plasma transferred arc boriding of a low carbon steel: microstructure and wear properties,” Appl. Surf. Sci., vol. 200, nos 1–4, pp. 203–218, 2002, https://doi.org/10.1016/S0169-4332(02)00901-7.Search in Google Scholar
[10] M. Darabara, G. D. Papadimitriou, and L. Bourithis, “Production of Fe–B–TiB2 metal matrix composites on steel surface,” Surf. Coating. Technol., vol. 201, no. 6, pp. 3518–3523, 2006, https://doi.org/10.1016/j.surfcoat.2006.08.105.Search in Google Scholar
[11] M. F. Buchely, J. C. Gutierrez, L. M. Leon, and A. Toro, “The effect of microstructure on abrasive wear of hardfacing alloys,” Wear, vol. 259, nos 1–6, pp. 52–61, 2005, https://doi.org/10.1016/j.wear.2005.03.002.Search in Google Scholar
[12] H. Berns, “Microstructural properties of wear-resistant alloys,” Wear, vols 181–183, no. P1, pp. 271–279, 1995, https://doi.org/10.1016/0043-1648(95)90034-9.Search in Google Scholar
[13] A. Zikin, E. Badisch, I. Hussainova, C. Tomastik, and H. Danninger, “Characterisation of TiC-NiMo reinforced Ni-based hardfacing,” Surf. Coating. Technol., vol. 236, pp. 36–44, 2013, https://doi.org/10.1016/j.surfcoat.2013.02.027.Search in Google Scholar
[14] T. Teker and A. Topal, “Properties and chemical composition of plasma arc welded Hardox450+FeW coatings,” Mater. Test., vol. 61, no. 1, pp. 35–40, 2019, https://doi.org/10.3139/120.111278.Search in Google Scholar
[15] M. Kirchgaßner, E. Badisch, and F. Franek, “Behaviour of iron-based hardfacing alloys under abrasion and impact,” Wear, vol. 265, nos 5–6, pp. 772–779, 2008, https://doi.org/10.1016/j.wear.2008.01.004.Search in Google Scholar
[16] X. Wu, G. Chen, “Nonequilibrium microstructures and their evolution in a Fe–Cr–W–Ni–C laser clad coating,” Mater. Sci. Eng., vol. 270, no. 2, pp.183–189, 1999, https://doi.org/10.1016/S0921-5093(99)00159-8.Search in Google Scholar
[17] L. Zhang, B. Liu, H. Yu, and D. Sun, “Rapidly solidified non-equilibrium microstructure and phase transformation of plasma cladding Fe-based alloy coating,” Surf. Coating. Technol., vol. 201, no. 12, pp. 5931–5936, 2007, https://doi.org/10.1016/j.surfcoat.2006.10.050.Search in Google Scholar
[18] A. Khajesarvi and G. H. Akbari, “Synthesis and structural characterization of nanocrystalline Ni50Al50 − xMox intermetallic compound prepared by mechanical alloying,” Russ. J. Non-Ferrous Metals, vol. 58, no. 4, pp. 411–417, 2017, https://doi.org/10.3103/S1067821217040083.Search in Google Scholar
[19] T. Teker and S. O. Yilmaz, “Metallurgical characterization of mechanically alloyed MoNiAl-WC reinforced Fe matrix composite,” Mater. Test., vol. 62, no. 12, pp. 1199–1204, 2020, https://doi.org/10.3139/120.111606.Search in Google Scholar
[20] M. Eroglu, “Boride coatings on steel using shielded metal arc welding electrode: microstructure and hardness,” Surf. Coating. Technol., vol. 203, no. 16, pp. 2229–2235, 2009, https://doi.org/10.1016/j.surfcoat.2009.02.010.Search in Google Scholar
[21] M. Yaz, “In situ formation of square shaped Fe2B borides in coated surface produced by GTAW,” J. Optoelectron. Adv. Mater., vol. 15, nos. 9–10, pp. 1037–1046, 2013.Search in Google Scholar
© 2021 Walter de Gruyter GmbH, Berlin/Boston
Articles in the same Issue
- Frontmatter
- Utilisation of the X-ray emission of an electron beam capillary for visualisation of the beam-material interaction
- Effect of Re and Ru additions on morphology and long-term stability of gamma prime particles in new modified superalloys prepared by a vacuum arc melting process
- Microstructure and fatigue performance of Cu-based M7C3-reinforced composites
- Influence of peroxide cross-linking temperature and time on mechanical, physical and thermal properties of polyethylene
- Fatigue behavior of bolted boreholes under various preloads
- Application of machine vision-based NDT technology in ceramic surface defect detection – a review
- An approach for obtaining surface residual stress based on indentation test and strain measurement
- Adhesive wear behavior of gas tungsten arc welded FeB-FeMo-C coatings
- Structural design optimization of the arc spring and dual-mass flywheel integrated with different optimization methods
- Tribological and adhesion properties of microwave-assisted borided AISI 316L steel
- Mechanical properties of wire arc additive manufactured carbon steel cylindrical component made by cold metal transferred arc welding process
- Improvement of the structural, thermal, and mechanical properties of polyurethane adhesives with nanoparticles and their application to Al/Al honeycomb sandwich panels
- Mechanical behavior of a friction welded AA6013/AA7075 beam
- Effects of carbon nanotubes on mechanical behavior of fiber reinforced composite under static loading
Articles in the same Issue
- Frontmatter
- Utilisation of the X-ray emission of an electron beam capillary for visualisation of the beam-material interaction
- Effect of Re and Ru additions on morphology and long-term stability of gamma prime particles in new modified superalloys prepared by a vacuum arc melting process
- Microstructure and fatigue performance of Cu-based M7C3-reinforced composites
- Influence of peroxide cross-linking temperature and time on mechanical, physical and thermal properties of polyethylene
- Fatigue behavior of bolted boreholes under various preloads
- Application of machine vision-based NDT technology in ceramic surface defect detection – a review
- An approach for obtaining surface residual stress based on indentation test and strain measurement
- Adhesive wear behavior of gas tungsten arc welded FeB-FeMo-C coatings
- Structural design optimization of the arc spring and dual-mass flywheel integrated with different optimization methods
- Tribological and adhesion properties of microwave-assisted borided AISI 316L steel
- Mechanical properties of wire arc additive manufactured carbon steel cylindrical component made by cold metal transferred arc welding process
- Improvement of the structural, thermal, and mechanical properties of polyurethane adhesives with nanoparticles and their application to Al/Al honeycomb sandwich panels
- Mechanical behavior of a friction welded AA6013/AA7075 beam
- Effects of carbon nanotubes on mechanical behavior of fiber reinforced composite under static loading
