Effects of blending poly(lactic acid) and thermoplastic polyester polyurethanes on the mechanical and adhesive properties in two-component injection molding
-
Marco Klute
,
Alexander Piontek
Abstract
One possible way to increase the use of bioplastics and thus contribute to a more resource-efficient and sustainable economy is to broaden the application range of such bioplastics. Poly(lactic acid) (PLA) is a promising and commercially available bio-based and biologically degradable polymer, which exhibits a high strength and stiffness but is very brittle. Blending with other polymers can lead to an enhancement of the ductility of the PLA. The goal of this work was to show that blending of PLA with a bio-based thermoplastic polyester-urethane elastomer (TPU) increases the ductility of the compound and also affects the adhesion of the layers when the materials – the modified PLA compound and the TPU – are processed via two-component (2C) injection molding to form corresponding composite parts. The results show that both goals – the increased ductility as well as the increased adhesion between the polymeric phases in 2C parts – can be reached by compounding PLA with two different bio-based polyester-based TPUs. Tensile strength and Young’s modulus of the compounds decrease according to a linear mixing rule with the addition of TPU. Elongation at break and notched Charpy impact strength increase by 750 and 200%, respectively. By addition of the TPU, the surface free energies of the compounds were increased, especially the polar parts. This led to reduced interfacial tensions between the produced compounds and the neat TPUs and thus increased the adhesion between them. For the softer TPU the adhesion was so strong that the TPU showed a cohesive failure in the 90° peel test and thus could not be separated from the compound substrate at all. For the harder TPU the bonding strength increased by 140% upon the addition of this TPU inside the hard component.
-
Author contributions: All the authors have accepted responsibility for the entire content of this submitted manuscript and approved submission.
-
Research funding: This project was funded by the German Federal Ministry of Food and Agriculture (BMEL) within the “renewable resources” funding program from the Agency for Renewable Resources (FNR) (FKZ: 22000915, 22011816, 22011916).
-
Conflict of interest statement: The authors declare no conflict of interest.
References
Anakabe, J., Zaldua Huici, A.M., Eceiza, A., and Arbelaiz, A. (2015). Melt blending of polylactide and poly(methyl methacrylate): thermal and mechanical properties and phase morphology characterization. J. Appl. Polym. Sci. 132: 1–8, https://doi.org/10.1002/app.42677.Suche in Google Scholar
Baldan, A. (2012). Adhesion phenomena in bonded joints. Int. J. Adhes. Adhes. 38: 95–116, https://doi.org/10.1016/j.ijadhadh.2012.04.007.Suche in Google Scholar
Bernardes, G.P., Rosa Luiz, N., Santana, R.M.C., and Camargo Forte, M.M. (2020). Influence of the morphology and viscoelasticity on the thermomechanical properties of poly(lactic acid)/thermoplastic polyurethane blends compatibilized with ethylene‐ester copolymer. J. Appl. Polym. Sci. 137: 48926, https://doi.org/10.1002/app.48926.Suche in Google Scholar
Cao, X., Dong, W., He, M., Zhang, J., Ren, F., and Li, Y. (2019). Effects of blending sequences and molecular structures of the compatibilizers on the morphology and properties of PLLA/ABS blends. RSC Adv. 9: 2189–2198, https://doi.org/10.1039/C8RA09193E.Suche in Google Scholar PubMed PubMed Central
Chen, D. and Zhen, W. (2021). Performance, interfacial compatibility testing and rheonaut technology analysis for simultaneous rheology and FTIR of poly(lactic acid)/modified saponite nanocomposites. Polym. Test. 100: 107232, https://doi.org/10.1016/j.polymertesting.2021.107232.Suche in Google Scholar
Di Bartolo, A., Infurna, G., and Dintcheva, N.T. (2021). A review of bioplastics and their adoption in the circular economy. Polymers 1–26, https://doi.org/10.3390/polym13081229.Suche in Google Scholar PubMed PubMed Central
European Bioplastics (2021). Bioplastics market data, Available at: https://www.european-bioplastics.org/market/ (Accessed 15 June 2021).Suche in Google Scholar
European Commission (2019). The European green deal COM 640 final, Available at: https://eur-lex.europa.eu/legal-content/EN/TXT/?uri=COM:2019:640:FIN (2019) (Accessed 15 June 2021).Suche in Google Scholar
Filho, W.L., Salvia, A.L., Bonoli, A., Saari, U.A., Voronova, V., Klõga, M., Kumbhar, S.S., Olszewski, K., de Quevedo, D.M., and Barbir, J. (2021). An assessment of attitudes towards plastics and bioplastics in Europe. Science of the total environment 755: 142732, https://doi.org/10.1016/j.scitotenv.2020.142732.Suche in Google Scholar PubMed
Fowkes, F.M. (1964). Attractive forces and interfaces. Ind. Eng. Chem. Res. 56: 40–52, https://doi.org/10.1021/ie50660a008.Suche in Google Scholar
Garlotta, D. (2001). A literature review of poly(lactic acid). J. Polym. Environ. 9: 63–84, https://doi.org/10.1023/A:1020200822435.10.1023/A:1020200822435Suche in Google Scholar
Gere, D. and Czigany, T. (2020). Future trends of plastic bottle recycling: compatibilization of PET and PLA. Polym. Test. 81: 106160, https://doi.org/10.1016/j.polymertesting.2019.106160.Suche in Google Scholar
Güzel, K., Klute, M., Kurgan, N., and Heim, H.-P. (2020). Influence of the degree of crystallinity and the surface free energy on the adhesion properties of different PLA/PBS blends in multicomponent injection molding. AIP Conference Proceedings 2205: 020019, https://doi.org/10.1063/1.5142934.Suche in Google Scholar
Hamad, K., Kaseem, M., Ayyoob, M., Joo, J., and Deri, F. (2018). Polylactic acid blends: the future of green, light and tough. Prog. Polym. Sci. 85: 83–127, https://doi.org/10.1016/j.progpolymsci.2018.07.001.Suche in Google Scholar
Institute for Bioplastics and Biocomposites (2020). Biopolymers, facts and statistics. IfBB – Institute for Bioplastics and Biocomposites, Hannover, https://www.ifbb-hannover.de/files/IfBB/downloads/faltblaetter_broschueren/f+s/Biopolymers-Facts-Statistics-2020.pdf.Suche in Google Scholar
Janczuk, B. and Bialopiotrowicz, T. (1989). Surface free-energy components of liquids and low energy solids and contact angles. J. Colloid Interface Sci. 127: 189–204.10.1016/0021-9797(89)90019-2Suche in Google Scholar
Kaelble, D.H. (1970). Dispersion-polar surface tension properties of organic solids. J. Adhes. 2: 66–81, https://doi.org/10.1080/0021846708544582.Suche in Google Scholar
Kang, H., Lu, X., and Xu, Y. (2015). Properties of immiscible and ethylene-butyl acrylate-glycidyl methacrylate terpolymer compatibilized poly (lactic acid) and polypropylene blends. Polym. Test. 43: 173–181, https://doi.org/10.1016/j.polymertesting.2015.03.012.Suche in Google Scholar
Kloubek, J. (1992). Development of methods for surface free energy determination using contact angles of liquids and solids. Adv. Colloid Interface Sci. 38: 99–142, https://doi.org/10.1016/0001-8686(92)80044-x.Suche in Google Scholar
Klute, M., Feldmann, M., and Heim, H.-P. (2018). Bio-based alternatives for hard-soft connections. Kunstst. Int. 40: 44.Suche in Google Scholar
Mieth, F. and Tromm, M. (2016). Multicomponent technologies. In: Specialized injection molding techniques. Elsevier, pp. 1–51.10.1016/B978-0-323-34100-4.00001-8Suche in Google Scholar
Mirabedini, S., Rahimi, H., Hamedifar, S., and Mohsen Mohseni, S. (2004). Microwave irradiation of polypropylene surface: a study on wettability and adhesion. Int. J. Adhes. 24: 163–170, https://doi.org/10.1016/j.ijadhadh.2003.09.004.Suche in Google Scholar
Nakajima, H., Dijkstra, P., and Loos, K. (2017). The recent developments in biobased polymers toward general and engineering applications: polymers that are upgraded from biodegradable polymers, analogous to petroleum-derived polymers, and newly developed. Polymers 9: 1–26, https://doi.org/10.3390/polym9100523.Suche in Google Scholar PubMed PubMed Central
Pilla, S. (2011). Handbook of Bioplastics and Biocomposites engineering applications. John Wiley & Sons, Hoboken, NJ, USA.10.1002/9781118203699Suche in Google Scholar
Piontek, A., Vernaez, O., and Kabasci, S. (2020). Compatibilization of poly(lactic acid) (PLA) and bio-based ethylene-propylene-diene-rubber (EPDM) via reactive extrusion with different coagents. Polymers 12: 1–21, https://doi.org/10.3390/polym12030605.Suche in Google Scholar PubMed PubMed Central
Przybysz-Romatowska, M., Haponiuk, J., and Formela, K. (2020). Poly(ε-Caprolactone)/Poly(Lactic acid) blends compatibilized by peroxide initiators: comparison of two strategies. Polymers 12: 1–12, https://doi.org/10.3390/polym12010228.Suche in Google Scholar PubMed PubMed Central
Rasselet, D., Caro-Bretelle, A.-S., Taguet, A., and Lopez-Cuesta, J.-M. (2019). Reactive compatibilization of PLA/PA11 blends and their application in additive manufacturing. Mater 12: 1–18, https://doi.org/10.3390/ma12030485.Suche in Google Scholar PubMed PubMed Central
Rauwendaal, C. (2014). Polymer extrusion, 5th ed. München: Hanser.10.3139/9781569905395Suche in Google Scholar
Rüppel, A. (2021). Untersuchung von Flüssigsilikonkautschuk-Polypropylen-Verbunden - Einflüsse der Lagerung und des Verarbeitungsprozesses auf die Haftungseigenschaften, Dissertation, Universität Kassel, Kassel, Germany.Suche in Google Scholar
Rüppel, A., Giesen, R.-U., and Heim, H.-P. (2017). The adhesion of LSR thermoplastic composites after storage tests. SPE ANTEC® 138: 142.Suche in Google Scholar
Schlitt, C.U., Hartung, M., Rüppel, A., Giesen, R.-U., and Heim, H.-P. (2019). UV pre-treatment for polycarbonate for bonding LSR in a multi-component injection molding process. Int. Polym. Proc. 34: 30–36, https://doi.org/10.3139/217.3509.Suche in Google Scholar
Spierling, S., Knüpffer, E., Behnsen, H., Mudersbach, M., Krieg, H., Springer, S., Albrecht, S., Herrmann, C., and Endres, H.-J. (2018). Bio-based plastics - a review of environmental, social and economic impact assessments. J. Clean. Prod. 185: 476–491, https://doi.org/10.1016/j.jclepro.2018.03.014.Suche in Google Scholar
Su, S., Kopitzky, R., Tolga, S., and Kabasci, S. (2019). Polylactide (PLA) and its blends with poly(butylene succinate) (PBS): a brief review. Polymers 11: 1–21, https://doi.org/10.3390/polym11071193.Suche in Google Scholar PubMed PubMed Central
United Nations (2015). Transforming our world: the 2030 Agenda for sustainable development, Available at: https://sdgs.un.org/2030agenda (Accessed 15 June 2021).Suche in Google Scholar
Wang, R., Zhang, J., Kang, H., and Zhang, L. (2016a). Design, preparation and properties of bio-based elastomer composites aiming at engineering applications. Compos. Sci. Technol. 133: 136–156, https://doi.org/10.1016/j.compscitech.2016.07.019.Suche in Google Scholar
Wang, S., Pang, S., Pan, L., Xu, N., and Li, T. (2016b). Isothermal cold crystallization, heat resistance, and tensile performance of polylactide/thermoplastic polyester elastomer (PLA/TPEE) blends: effects of annealing and reactive compatibilizer. Polymers 8: 1–16, https://doi.org/10.3390/polym8120417.Suche in Google Scholar PubMed PubMed Central
Yokohara, T. and Yamaguchi, M. (2008). Structure and properties for biomass-based polyester blends of PLA and PBS. Eur. Polym. J. 44: 677–685, https://doi.org/10.1016/j.eurpolymj.2008.01.008.Suche in Google Scholar
Zhao, X., Hu, H., Wang, X., Yu, X., Zhou, W., and Peng, S. (2020). Super tough poly(lactic acid) blends: a comprehensive review. RSC Adv. 10: 13316–13368, https://doi.org/10.1039/D0RA01801E.Suche in Google Scholar
© 2022 Walter de Gruyter GmbH, Berlin/Boston
Artikel in diesem Heft
- Frontmatter
- Review Articles
- Electron beam processing of rubbers and their composites
- A review on graphene/rubber nanocomposites
- Recent advances on melt-spun fibers from biodegradable polymers and their composites
- Research Articles
- Toughened poly(butylene succinate)/polylactide/poly(vinyl acetate) ternary blend without sacrificing the strength
- Investigation on the sealing performance of polymers at ultra high pressures
- Effect mechanism of acidification and vulcanization on SBS-modified asphalt
- Effects of blending poly(lactic acid) and thermoplastic polyester polyurethanes on the mechanical and adhesive properties in two-component injection molding
- Mechanical and morphological characterization of sisal/kenaf/pineapple mat reinforced hybrid composites
- News
- PPS News
Artikel in diesem Heft
- Frontmatter
- Review Articles
- Electron beam processing of rubbers and their composites
- A review on graphene/rubber nanocomposites
- Recent advances on melt-spun fibers from biodegradable polymers and their composites
- Research Articles
- Toughened poly(butylene succinate)/polylactide/poly(vinyl acetate) ternary blend without sacrificing the strength
- Investigation on the sealing performance of polymers at ultra high pressures
- Effect mechanism of acidification and vulcanization on SBS-modified asphalt
- Effects of blending poly(lactic acid) and thermoplastic polyester polyurethanes on the mechanical and adhesive properties in two-component injection molding
- Mechanical and morphological characterization of sisal/kenaf/pineapple mat reinforced hybrid composites
- News
- PPS News
