Skip to main content
Article Open Access

Dry Sliding Wear Behaviours of Valve Seat Inserts Produced from High Chromium White Iron

  • ORCID logo EMAIL logo , , and
Published/Copyright: December 18, 2014
Download Article (PDF)
High Temperature Materials and Processes
From the journal High Temperature Materials and Processes Volume 34 Issue 7

Received: 2014-6-24
Accepted: 2014-10-2
Published Online: 2014-12-18
Published in Print: 2015-11-1

©2015 by De Gruyter

Articles in the same Issue

  1. Frontmatter
  3. The Influence of the Induced Ferrite and Precipitates of Ti-bearing Steel on the Ductility of Continuous Casting Slab
  4. Study on Evolution of Ti-containing Intermetallic Compounds in Alloy 2618-Ti during Homogenization
  5. The Effects of Different P2O5 Content and Basicity on Phosphorus Enrichment in the CaO-SiO2-FetO-P2O5 Slag System
  6. Dry Sliding Wear Behaviours of Valve Seat Inserts Produced from High Chromium White Iron
  7. A Characterization for the Hot Flow Behaviors of As-extruded 7050 Aluminum Alloy
  8. A Characterization of Hot Flow Behaviors Involving Different Softening Mechanisms by ANN for As-Forged Ti-10V-2Fe-3Al Alloy
  9. Effect of Microwave Heating Conditions on the Preparation of High Surface Area Activated Carbon from Waste Bamboo
  10. Laboratory Study on Oxide Inclusions in High-Strength Low-Alloyed Steel Refined by Slag with Basicity 2–5
  11. Processing and Characterization of CrB2-Based Novel Composites
  12. Dispersion of Particles in the Emulsion by the Electric Current
  13. Description of Grain Refinement by Dynamic Recrystallization Under Hot Compressions for As-Extruded 3Cr20Ni10W2 Heat-Resistant Alloy
  14. Identification of Stable Processing Parameters in Ti–6Al–4V Alloy from a Wide Temperature Range Across β Transus and a Large Strain Rate Range
  15. Life Estimation and Creep Damage Quantification of Service Exposed Reformer Tube
https://doi.org/10.1515/htmp-2014-0110
Keywords for this article
valve seat insert; wear behaviour; Cr rate; high chromium white cast iron
Creative Commons
BY-NC-ND 3.0

Articles in the same Issue

  1. Frontmatter
  3. The Influence of the Induced Ferrite and Precipitates of Ti-bearing Steel on the Ductility of Continuous Casting Slab
  4. Study on Evolution of Ti-containing Intermetallic Compounds in Alloy 2618-Ti during Homogenization
  5. The Effects of Different P2O5 Content and Basicity on Phosphorus Enrichment in the CaO-SiO2-FetO-P2O5 Slag System
  6. Dry Sliding Wear Behaviours of Valve Seat Inserts Produced from High Chromium White Iron
  7. A Characterization for the Hot Flow Behaviors of As-extruded 7050 Aluminum Alloy
  8. A Characterization of Hot Flow Behaviors Involving Different Softening Mechanisms by ANN for As-Forged Ti-10V-2Fe-3Al Alloy
  9. Effect of Microwave Heating Conditions on the Preparation of High Surface Area Activated Carbon from Waste Bamboo
  10. Laboratory Study on Oxide Inclusions in High-Strength Low-Alloyed Steel Refined by Slag with Basicity 2–5
  11. Processing and Characterization of CrB2-Based Novel Composites
  12. Dispersion of Particles in the Emulsion by the Electric Current
  13. Description of Grain Refinement by Dynamic Recrystallization Under Hot Compressions for As-Extruded 3Cr20Ni10W2 Heat-Resistant Alloy
  14. Identification of Stable Processing Parameters in Ti–6Al–4V Alloy from a Wide Temperature Range Across β Transus and a Large Strain Rate Range
  15. Life Estimation and Creep Damage Quantification of Service Exposed Reformer Tube
Downloaded on 21.4.2026 from https://www.degruyterbrill.com/document/doi/10.1515/htmp-2014-0110/html
Scroll to top button