Co-precipitation behaviour of titanium-containing silicate solution
-
Hui-Hong Lü
,
Min-Zhi Wu
Abstract
The co-precipitation behaviour of a simulated Al2(SO4)3–TiOSO4–Na2SiO3 solution that imitated the lixivium of Ti-bearing blast furnace slag (Ti-slag) leached by sulphuric acid was investigated in this study. Various chemical analyses were employed to study the selective precipitation of multiple target components. Based on the high-added-value applications of Ti-slag, a new method was developed to prepare aluminium titanate composites from titanium-containing silicates. The findings demonstrate that the onsets of Ti and Al precipitation occur at pH values of 3.5 and 5.0, respectively, followed by Si precipitation. The particle sizes of the co-precipitates were greatly influenced by the precipitants, pH and the initial Al/Ti mole ratio. The results also show that the precipitation ratio of Ti, Al and Si generally increases with the pH and temperature, regardless of the Al/Ti mole ratio. The Si-O-Al, Ti-O-Al, and Ti-O-Si bonds that were formed were dependent on the pH and the initial Al/Ti mole ratio. There was a synthesis path for β-Al2TiO5 (AT) from the solid-state reaction between rutile and α-Al2O3 at 1362.5°C. The AT composites were successfully prepared by sintering the co-precipitates at 1450°C, which exhibited good thermal stability as estimated by the XRD measurements of the sample annealed at 1200°C for 4 hours.
Acknowledgements
This work was supported by grants from the National Natural Science Foundation of China (nos.51204004and51274006), University Science Research Project of Anhui Province (KJ2016A810), the Natural Science Foundation of China (U1660110) and Anhui Innovation Team Project of New Technology in Materialisation of Metallurgical Solid Wastes.
References
Aravind, P. R., Mukundan, P., Pillai, P. K., & Warrier, K. G. K. (2006). Mesoporous silica–alumina aerogels with high thermal pore stability through hybrid sol–gel route followed by subcritical drying. Microporous and Mesoporous Materials, 96, 14–20. 10.1016/j.micromeso.2006.06.014.Suche in Google Scholar
Belver, C., Muńoz, M. A. B., & Vicente, M. A. (2002). Chemical activation of a kaolinite under acid and alkaline conditions. Chemistry of Materials, 14, 2033–2043. 10.1021/cm0111736.Suche in Google Scholar
Chakravorty, A. K., & Ghosh, D. K. (1988). Synthesis and 980°C phase development of some mullite gels. Journal of the American Ceramic Society, 71, 978–987. 10.1111/j.1151-2916.1988.tb07568.x.Suche in Google Scholar
Chen, D. S., Zhao, L. S., Liu, Y. H., Qi, T., Wang, J. C., & Wang, L. N. (2013). A novel process for recovery of iron, titanium and vanadium from titanomagnetite concentrates: NaOH molten salt roasting and water leaching processes. Journal of Hazardous Materials, 244–245, 588–595. 10.1016/j.jhazmat.2012.10.052.Suche in Google Scholar
Di Valentin, C., Finazzi, E., Pacchioni, G., Selloni, A., Livraghi, S., Paganini, M. C., & Giamello, E. (2007). N-doped TiO2: Theory and experiment. Chemical Physics, 339, 44–56. 10.1016/j.chemphys.2007.07.020.Suche in Google Scholar
Du, X. L., Wang, Y. Q., Su, X. H., & Li, J. G. (2009). Influences of pH value on the microstructure and phase transformation of aluminum hydroxide. Powder Technology, 192, 40–46. 10.1016/j.powtec.2008.11.008.Suche in Google Scholar
Duan, J. M., & Gregory, J. (2003). Coagulation by hydrolysing metal salts. Advances in Colloid and Interface Science, 100–102, 475–502. 10.1016/s0001-8686(02)00067-2.Suche in Google Scholar
El-Masry, M. H., Sadek, O. M., & Mekhemer, W. K. (2004). Purification of raw surface water using electro-coagulation method. Water, Air & Soil Pollution, 158, 373–385. 10.1023/b:wate.0000044857.02199.45.Suche in Google Scholar
Farmer, V. C. (1974). The infrared spectra of minerals. London, UK: Mineralogical Society. 10.1180/mono-4.Suche in Google Scholar
Huang, Y. X, Senos, A. M. R., Rocha, J., & Baptista, J. L. (1997). Gel formation in mullite precursors obtained via tetraethylorthosilicate (TEOS) pre-hydrolysis. Journal of Materials Science, 32, 105–110. 10.1023/a:1018575115 770.Suche in Google Scholar
Huang, Y. X., Senos, A. M. R., & Baptista, J. L. (1998). Effect of excess SiO2 on the reaction sintering of aluminium titanate-25 vol. % mullite composites. Ceramics International, 24, 223–228. 10.1016/s0272-8842(97)00006-0.Suche in Google Scholar
Jung, Y.S., Kim, D.W., Kim, Y.S., Park, E.K., & Baeck, S. H. (2008). Synthesis of alumina–titania solid solution by sol–gel method. Journal of Physics and Chemistry of Solids, 69, 1464–1467. 10.1016/j.jpcs.2007.10.037.Suche in Google Scholar
Kim, J. H., Kim, M. W., & Yu, J. S. (2011). Recycle of silicate waste into mesoporous materials. Environmental Science & Technology, 45, 3695–3701. 10.1021/es103510r.Suche in Google Scholar PubMed
Kimura, T., Suzuki, M., Ikeda, T., Kato, K., Maeda, M., & Tomura, S. (2006). Silica-based mesoporous materials derived from Ti containing layered polysilicate kanemite. Microporous and Mesoporous Materials, 95, 146–153. 10.1016/j.micromeso.2006.05.021.Suche in Google Scholar
Kurc, B. (2014). Gel electrolytes based on poly(acrylonitrile)/ sulpholane with hybrid TiO2/SiO2 filler for advanced lithium polymer batteries. Electrochimica Acta, 125, 415–420. 10.1016/j.electacta.2014.01.117.Suche in Google Scholar
Lee, S. O., Jung, K. H., Oh, C. J., Lee, Y. H., Tran, T., & Kim, M. J. (2009). Precipitation of fine aluminium hydroxide from Bayer liquors. Hydrometallurgy, 98, 156–161. 10.1016/j.hydromet.2009.04.014.Suche in Google Scholar
Li, L.S., Liu, J. B., Wu, X. R., Ren, X., Bing, W. B., & Wu, L. S. (2010). Influence of Al2O3 on equilibrium sinter phase in N2 atmosphere. ISIJ International, 50, 327–329. 10.2355/isijinternational.50.327.Suche in Google Scholar
Li, L. S., & Lu, T. T. (2011). Condensation mechanism and influencing factor of stability of complicated silicic acid system. AICHE Journal, 57, 1339–1343. 10.1002/aic.12374.Suche in Google Scholar
Liu, Q., Wang, A. Q., Wang, X. H., Gao, P., Wang, X. D., & Zhang, T. (2008). Synthesis, characterization and catalytic applications of mesoporous γ-alumina from boehmite sol. Microporous and Mesoporous Materials, 111, 323–333. 10.1016/j.micromeso.2007.08.007.Suche in Google Scholar
Liu, P.C., Zhu, Y.Z., Ma, J.H., Yang, S.G., Gong, J.H., & Jian, X. (2013). Effect of boehmite sol on the crystallization behaviour and densification of mullite formed from a sol–gel precursor. Progress in Natural Science: Materials International, 23, 145–151. 10.1016/j.pnsc.2013.02.004.Suche in Google Scholar
Lü, H. H., Li, N., Wu, X. R., Li, L. S., Gao, Z. F., & Shen, X. M. (2013). A novel conversion of Ti-bearing blast-furnace slag into water splitting photocatalyst with visible-light-response. Metallurgical and Materials Transaction B, 44, 1317–1320. 10.1007/s11663-013-9973-y.Suche in Google Scholar
Matsuda, A., Higashi, Y., Tadanaga, K., & Tatsumisago, M. (2006). Hot-water treatment of sol–gel derived SiO2–TiO2 microparticles and application to electrophoretic deposition for thick films. Journal of Materials Science, 41, 8101–8108. 10.1007/s10853-006-0419-7.Suche in Google Scholar
Oikonomou, P., Dedeloudis, C., Stournaras, C. J., & Ftikos, C. (2007). Stabilized tialite–mullite composites with low thermal expansion and high strength for catalytic converters. Journal of the European Ceramic Society, 27, 3475–3482. 10.1016/j.jeurceramsoc.2006.07.020.Suche in Google Scholar
Okada, K., & Otsuka, N. (1986). Characterization of the spinel phase from SiO2–Al2O3 xerogels and the formation process of mullite. Journal of the American Ceramic Society, 69, 652–656. 10.1111/j.1151-2916.1986.tb07466.x.Suche in Google Scholar
Periyat, P., Baiju, K. V., Mukundan, P., Pillai, P. K., & Warrier, K. G. K. (2008). High temperature stable mesoporous anatase TiO2 photocatalyst achieved by silica addition. Applied Catalysis A, 349, 13–19. 10.1016/j.apcata.2008. 07.022.Suche in Google Scholar
Pourbaix, M. (1974). Atlas of electrochemical equilibria in aqueous solutions. Oxford, UK: Pergamon.Suche in Google Scholar
Richmond, W. R., Jones, R. L., & Fawell, P. D. (1998). The relationship between particle aggregation and rheology in mixed silica–titania suspensions. Chemical Engineering Journal, 71, 67–75. 10.1016/s1385-8947(98)00105-3.Suche in Google Scholar
Schneider, H., & Komarneni, S. (2005). Mullite. Weinheim, Germany: Wiley. 10.1002/3527607358.Suche in Google Scholar
Sobhani, M., Ebadzadeh, T., & Rahimipour, M. R. (2014). Formation and densification behavior of reaction sintered alumina-20 wt. % aluminium titanate nano-composites. International Journal of Refractory Metals and Hard Materials, 47, 49–53. 10.1016/j.ijrmhm.2014.06.018.Suche in Google Scholar
Wellia, D. V., Xu, Q. C., Sk, M. A., Lim, K. H., Lim, T. M., & Tan, T. T. Y. (2011). Experimental and theoretical studies of Fe-doped TiO2 films prepared by peroxo sol–gel method. Applied Catalysis A, 401, 98–105. 10.1016/j.apcata.2011.05.003.Suche in Google Scholar
Wu, Z.J., Yue, H. F., Li, L. S., Jiang, B.F., Wu, X.R., & Wang, P. (2010). Synthesis and electrochemical properties of multi-doped LiFePO4/C prepared from the steel slag. Journal of Power Sources, 195, 2888–2893. 10.1016/j.jpowsour.2009.11.058.Suche in Google Scholar
Wu, X. R., Wang, H. H., Li, L. S., Lü, H. H., Wu, Z. J., & Shen, X. M. (2013a). Synthesis of cordierite powder from blast furnace slag. Transactions of the Indian Ceramic Society, 72, 197–200. 10.1080/0371750x.2013.851622.Suche in Google Scholar
Wu, X. R., Lü, H. H., Li, L. S., Wang, P., Shen, X. M., Zhu, J. H., Cao, F. B., & Li, M. H. (2013b). China Patent No. 201110101537.3. Beijing, China: China Patent & Trademark Office. http://www.pss-system.gov.cn/sipopublicsearch/search/searchHome-searchIndex.shtml?params=991CFE73D4DF553253D44E119219BF31366856FF4B1522 26CAE4DB031259396ASuche in Google Scholar
Xie, X., Sun, J., Liu, Y., & Jiang, W. (2010). Use of silica sol as a transient phase for fabrication of aluminium titanate–mullite ceramic composite. Scripta Materialia, 63, 641–644. 10.1016/j.scriptamat.2010.05.038.Suche in Google Scholar
Zhou, S. X., Antonietti, M., & Niederberger, M. (2007). Low-temperature synthesis of γ-alumina nanocrystals from aluminum acetylacetonate in nonaqueous media. Small, 3, 763–767. 10.1002/smll.200700027.Suche in Google Scholar PubMed
© 2016 Institute of Chemistry, Slovak Academy of Sciences
Artikel in diesem Heft
- Review
- Sulphur and peroxide vulcanisation of rubber compounds – overview
- Original paper
- Isolation of sporopollenin-like biopolymer from Aspergillus niger and its characterisation
- Original paper
- Clustering analysis of different hop varieties according to their essential oil composition measured by GC/MS
- Original paper
- Determination of vapor—liquid equilibrium diagrams of multicomponent systems
- Original paper
- Enhancing lithium–sulphur battery performance by copper oxide@graphene oxide nanocomposite-modified cathode
- Original paper
- Magnetic properties of binary and ternary mixed metal oxides NiFe2O4 and Zn0.5Ni0.5Fe2O4 doped with rare earths by sol—gel synthesis
- Original paper
- Graphite felt modified with electroless Co–Ni–P alloy as an electrode material for electrochemical oxidation and reduction of polysulfide species
- Original paper
- Preparation and artificial ageing tests in stone conservation of fluorosilicone vinyl acetate/acrylic/epoxy polymers
- Original paper
- Co-precipitation behaviour of titanium-containing silicate solution
- Original paper
- Magnetic fluids’ stability improved by oleic acid bilayer-coated structure via one-pot synthesis
- Original paper
- Synthesis of 5-hydroxymethylfurfural from glucose in a biphasic medium with AlCl3 and boric acid as the catalyst
- Original paper
- Facile and efficient synthesis of xanthenedione derivatives promoted by niobium pentachloride
Artikel in diesem Heft
- Review
- Sulphur and peroxide vulcanisation of rubber compounds – overview
- Original paper
- Isolation of sporopollenin-like biopolymer from Aspergillus niger and its characterisation
- Original paper
- Clustering analysis of different hop varieties according to their essential oil composition measured by GC/MS
- Original paper
- Determination of vapor—liquid equilibrium diagrams of multicomponent systems
- Original paper
- Enhancing lithium–sulphur battery performance by copper oxide@graphene oxide nanocomposite-modified cathode
- Original paper
- Magnetic properties of binary and ternary mixed metal oxides NiFe2O4 and Zn0.5Ni0.5Fe2O4 doped with rare earths by sol—gel synthesis
- Original paper
- Graphite felt modified with electroless Co–Ni–P alloy as an electrode material for electrochemical oxidation and reduction of polysulfide species
- Original paper
- Preparation and artificial ageing tests in stone conservation of fluorosilicone vinyl acetate/acrylic/epoxy polymers
- Original paper
- Co-precipitation behaviour of titanium-containing silicate solution
- Original paper
- Magnetic fluids’ stability improved by oleic acid bilayer-coated structure via one-pot synthesis
- Original paper
- Synthesis of 5-hydroxymethylfurfural from glucose in a biphasic medium with AlCl3 and boric acid as the catalyst
- Original paper
- Facile and efficient synthesis of xanthenedione derivatives promoted by niobium pentachloride
