Startseite Solidification microstructures of Cu–Zr–Al–Y BMG produced by casting in a wedge-shaped copper mold
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Solidification microstructures of Cu–Zr–Al–Y BMG produced by casting in a wedge-shaped copper mold

  • Ke Yang , Xinhui Fan , Bing Li , Yanhong Li und Xin Wang
Veröffentlicht/Copyright: 22. Februar 2017
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 108 Heft 3

Abstract

In this paper, Cu43Zr48Al9 and (Cu43Zr48Al9)98Y2 bulk metallic glasses were prepared by casting them in a wedge-shaped copper mold. X-ray diffraction, optical microscopy, scanning electron microscopy and transmission electron microscopy were used to analyze their microstructures. Wedge casting is an effective and flexible technique for exploring alloy solidification microstructures. The results demonstrate that the development of microstructural transitions is related to the thickness of the wedge-shaped samples. These microstructural transitions are represented by the appearance of altered microstructural morphologies as well as changes from one product structure to another. It is found that the crystal/glass transition occurs as a U-shape change in Cu-based wedge-shaped alloys. Further, the critical cooling rate of (Cu43Zr48Al9)98Y2 became lower than that of Cu43Zr48Al9 and that (Cu43Zr48Al9)98Y2 has a better glass forming ability. We developed practical strategies in microstructure control to extend our knowledge of phase competition leading to the successful synthesis of Cu-based metallic glass.

Keywords: Metallic glass; Wedge-shaped casting; Rapid solidification; Microstructure
*Correspondence address, Prof. Xinhui Fan, School of Material and Chemical Engineering, Xi'an Technological University, Xuefu Middle Road No. 2, Xi'an 710021, China, Tel.: +86-29-86173323, Fax: +86-29-86173323, E-mail:

References

[1] A.Inoue, K.Ohtera, K.Kita, T.Masumoto: Jpn. J. Appl. Phys.27 (1988) L2248. 27.L2248. 10.1143/JJAPSuche in Google Scholar

[2] A.Inoue, T.Zhang, T.Masumoto: Mater. Trans. JIM31 (1990) 425. 10.2320/matertrans1989.31.425Suche in Google Scholar

[3] V.Ponnambalam, S.J.Poon, G.J.Shiflet: J. Mater. Res.19 (2004) 1320. 10.1557/JMR.2004.0176Suche in Google Scholar

[4] S.L.Zhu, X.M.Wang, A.Inoue: Intermetallics16 (2008) 1031. 10.1016/j.intermet.2008.05.006Suche in Google Scholar

[5] A.Inoue, T.Zhang: Mater. Trans. JIM37 (1996) 185. 10.2320/matertrans1989.37.185Suche in Google Scholar

[6] Q.S.Zhang, W.Zhang, A.Inoue: Mater. Trans. JIM48 (2007) 629. 10.2320/matertrans.48.629Suche in Google Scholar

[7] R.Li, S.Pang, C.Ma, T.Zhang: Acta Mater.55 (2007) 3719. 10.1016/j.actamat.2007.02.026Suche in Google Scholar

[8] Q.Zheng, J.Xu, E.Ma: J. Appl. Phys.102 (2007) 113519. 10.1063/1.2821755Suche in Google Scholar

[9] A.Inoue: Acta Mater.48 (2000) 279. 10.1016/S1359-6454(99)00300-6Suche in Google Scholar

[10] W.H.Wang, C.Dong, C.H.Shek: Mater. Sci. Eng. R44 (2004) 45. 10.1016/j.mser.2004.03.001Suche in Google Scholar

[11] D.Turnbull: Contemporary Physics10 (1969) 473. 10.1080/00107516908204405Suche in Google Scholar

[12] Z.P.Lu, C.T.Liu: Acta Mater.50 (2002) 3501. 10.1016/S1359-6454(02)00166-0Suche in Google Scholar

[13] Y.Li, S.C.Ng, C.K.Ong, H.H.Hng, T.T.Goh: Scr. Mater.36 (1997) 783. 10.1016/S1359-6462(96)00448-4Suche in Google Scholar

[14] A.Inoue: Mater. Sci. Eng. A226–228 (1997) 357. 1016/S0921-5093(97)80049-4Suche in Google Scholar

[15] A.Inoue: Acta Mater.48 (2000) 279. 10.1016/S1359-6454(99)00300-6Suche in Google Scholar

[16] X.Cui, F.Q.Zu, Z.Z.Wang, Z.Y.Huang, X.Y.Li, L.F.Wang: Intermetallics36 (2013) 21. 10.1016/j.intermet.2012.12.008Suche in Google Scholar

[17] Y.Wu, H.Wang, H.H.Wu, Z.Y.Zhang, X.D.Hui, G.L.Chen, D.Ma, X.L.Wang, Z.P.Lu: Acta Mater.59 (2011) 2928. 10.1016/j.actamat.2011.01.029Suche in Google Scholar

[18] Y.Wu, Y.H.Xiao, G.L.Chen, C.T.Liu, Z.P.Lu: Adv. Mater.22 (2010) 2770. 10.1002/adma.201000482Suche in Google Scholar PubMed

[19] J.M.Liu, H.F.Zhang, H.M.Fu, Z.Q.Hu, X.G.Yuan: J. Mater. Res.25 (2011) 1159. 10.1557/JMR.2010.0138Suche in Google Scholar

Received: 2016-09-25
Accepted: 2016-11-29
Published Online: 2017-02-22
Published in Print: 2017-03-13

© 2017, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Original Contributions
  4. Effect of grain defects on the mechanical behavior of nickel-based single crystal superalloy
  5. Evolution of mechanical properties and microstructure of differently cryogenically treated hot die steel AISI–H13
  6. Microstructure and mechanical properties of nickel particle reinforced magnesium composite: impact of reinforcement introduction method
  7. Microstructure and mechanical properties of carbon nanotube-reinforced ZK61 magnesium alloy composites prepared by spark plasma sintering
  8. Solidification microstructures of Cu–Zr–Al–Y BMG produced by casting in a wedge-shaped copper mold
  9. Energy spectrum analysis of anodic oxidation film surface–interface on 7475 aluminum alloy after salt spray corrosion
  10. Fabrication of Ni/SiC composite powder by mechanical alloying and its effects on properties of copper matrix composites
  11. The sintering behavior and physical properties of Li2CO3-doped Bi0.5(Na0.8K0.2)0.5TiO3 lead-free ceramics
  12. The effect of heating rate on the microstructural breakdown required for thixoformability
  13. Nano-particles in powder injection molding of an aluminum matrix composite: Rheological behavior, production and properties
  14. Short Communications
  15. Preparation of vaterite CaCO3 microspheres by fast precipitation method
  16. Slag corrosion resistance of Al4SiC4
  17. DGM News
  18. DGM News
https://doi.org/10.3139/146.111464
Schlagwörter für diesen Artikel
Metallic glass; Wedge-shaped casting; Rapid solidification; Microstructure

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Original Contributions
  4. Effect of grain defects on the mechanical behavior of nickel-based single crystal superalloy
  5. Evolution of mechanical properties and microstructure of differently cryogenically treated hot die steel AISI–H13
  6. Microstructure and mechanical properties of nickel particle reinforced magnesium composite: impact of reinforcement introduction method
  7. Microstructure and mechanical properties of carbon nanotube-reinforced ZK61 magnesium alloy composites prepared by spark plasma sintering
  8. Solidification microstructures of Cu–Zr–Al–Y BMG produced by casting in a wedge-shaped copper mold
  9. Energy spectrum analysis of anodic oxidation film surface–interface on 7475 aluminum alloy after salt spray corrosion
  10. Fabrication of Ni/SiC composite powder by mechanical alloying and its effects on properties of copper matrix composites
  11. The sintering behavior and physical properties of Li2CO3-doped Bi0.5(Na0.8K0.2)0.5TiO3 lead-free ceramics
  12. The effect of heating rate on the microstructural breakdown required for thixoformability
  13. Nano-particles in powder injection molding of an aluminum matrix composite: Rheological behavior, production and properties
  14. Short Communications
  15. Preparation of vaterite CaCO3 microspheres by fast precipitation method
  16. Slag corrosion resistance of Al4SiC4
  17. DGM News
  18. DGM News
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 16.11.2025 von https://www.degruyterbrill.com/document/doi/10.3139/146.111464/pdf
Button zum nach oben scrollen