Startseite Effect of trace Ti on the microstructure and mechanical properties of AM50 alloy
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Effect of trace Ti on the microstructure and mechanical properties of AM50 alloy

  • Q. D. Wang , J. B. Lin , M. P. Liu und W. J. Ding
Veröffentlicht/Copyright: 23. Mai 2013
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 99 Heft 7

Abstract

The effect of trace additions (0 – 0.1 wt.%) of titanium on the microstructure, mechanical properties and creep resistance of an AM50 alloy have been studied. The microstructure was examined using optical microscopy and scanning electron microscopy. Results showed that the microstructures of AM50 alloy were obviously refined by trace Ti addition, although the actual content of Ti was only about 0.0025 – 0.0079 wt.%. The refining ability of titanium was ascribed to its large growth restriction factor, and it can be described as a constitutional undercooling driven mechanism. As-cast samples were subjected to tensile tests at room temperature, 150 °C and 200 °C. A considerable increase in tensile properties was observed due to grain refinement, especially the ultimate tensile strength and elongation. In addition, the creep resistance of AM50 alloy was dramatically increased by Ti addition.

Keywords: Magnesium alloy; Titanium; Grain refining; Microstructure; Mechanical properties
* Correspondence address, Wang Qudong National Engineering Research Center of Light Alloy Net Forming School of Materials Science & Engineering Shanghai Jiaotong University Dongchuan Road 800, Shanghai 200240, P.R. China Tel.: +86 21 54742715 Fax: +86 21 34202794 E-mail:

References

[1] Z.Shan, A.M.Gokhale: Mater. Sci. Eng. A361(2003)267.10.1016/S0921-5093(03)00529-XSuche in Google Scholar

[2] V.Sklenicka, M.Pahutova, K.Kucharova, M.Svoboda, T.G.Langdon: Metall. Mater. Trans. A33(2002)883.10.1007/s11661-002-0158-6Suche in Google Scholar

[3] G.S.Cole: Mater. Sci. Forum419–422(2003)43.10.4028/www.scientific.net/MSF.419-422.43Suche in Google Scholar

[4] S.Schumann, H.Friedrich: Mater. Sci. Forum419–422(2003)51.10.4028/www.scientific.net/MSF.419-422.51Suche in Google Scholar

[5] S.Ji, M.Qian, Z.Fan: Metall. Mater. Trans. A: Physical Metallurgy and Materials Science37(2006)779.10.1007/s11661-006-0049-3Suche in Google Scholar

[6] D.Lahaie, J.D.Embury, M.M.Chadwick, G.T.Gray: Scr. Metall. Mater.27(1992)139.10.1016/0956-716X(92)90102-KSuche in Google Scholar

[7] K.Kubota, M.Mabuchi, K.Higashi: J. Mater. Sci.34(1999)2255.10.1023/A:1004561205627Suche in Google Scholar

[8] T.Mohri, M.Mabuchi, N.Saito, M.Nakamura: Mater. Sci. Eng. A257(1998)287.10.1016/S0921-5093(98)00853-3Suche in Google Scholar

[9] T.Mukai, M.Yamanoi, H.Watanabe, K.Ishikawa, K.Higashi: Mater. Trans.42(2001)1177.10.2320/matertrans.42.1177Suche in Google Scholar

[10] M.Qian, A.Das: Scr. Mater.54(2006)881.10.1016/j.scriptamat.2005.11.002Suche in Google Scholar

[11] M.Johnsson, L.Bäckerud: Z. Metallkd.87(1996)216.10.1515/ijmr-1996-870312Suche in Google Scholar

[12] A.L.Greer, A.M.Brunn, A.Tronche, P.V.Evans, D.J.Bristow: Acta Mater.48(2000)2823.10.1016/S1359-6454(00)00094-XSuche in Google Scholar

[13] H.Polmear: Mater. Sci. Technol.10(1994)1.10.1179/mst.1994.10.1.1Suche in Google Scholar

[14] G.Chadha, J.E.Allison, J.W.Jones, in: A.A.Luo (Ed.), Magnesium technology 2004, TMS, Warrendale, PA, 2004, p. 181.Suche in Google Scholar

[15] S.M.He, L.M.Peng, X.Q.Zeng: Mater. Sci. Forum488–489(2005)231.10.4028/www.scientific.net/MSF.488-489.231Suche in Google Scholar

[16] M.O.Pekgüleryüz: Mater. Sci. Forum350–351(2000)131.Suche in Google Scholar

[17] J.Hunt: Mater. Sci. Eng.65(1984)75.10.1016/0025-5416(84)90201-5Suche in Google Scholar

[18] Y.X.Wang, X.Q.Zeng, W.J.Ding: Scr. Mater.54(2006)269.10.1016/j.scriptamat.2005.09.022Suche in Google Scholar

[19] M.Johnsson: Z. Metallkd.85(1994)781.10.1515/ijmr-1994-851108Suche in Google Scholar

[20] M.A.Easton, D.H.St John: Acta Mater.49(2001)1867.10.1016/S1359-6454(00)00368-2Suche in Google Scholar

[21] I.Maxwell, A.Hellawell: Acta Met.23(1975)229.10.1016/0001-6160(75)90188-1Suche in Google Scholar

[22] J.L.Murray: Bull. Alloy Phase Diagrams245-248(1986)305.10.1007/BF02868999Suche in Google Scholar

[23] Y.C.Lee, A.K.Dahle, D.H.St John: Metal. Mater. Trans. A31(2000)2895.10.1007/BF02830349Suche in Google Scholar

[24] H.Li, T.Sritharan, Y.M.Lam, N.Y.Leng: J. Mater. Sci. Technol.66(1997)253.10.1016/S0924-0136(96)02536-8Suche in Google Scholar

[25] M.Bamberger: Mater. Sci. Technol.17(2001)15.10.1179/026708301101509061Suche in Google Scholar

[26] 2002 JCPDS – International Centre for Diffraction Data, PCPDFWIN v. 2.3.Suche in Google Scholar

Received: 2007-8-31
Accepted: 2008-5-3
Published Online: 2013-05-23
Published in Print: 2008-07-01

© 2008, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Basic
  4. On the reaction scheme and liquidus surface in the ternary system Al–Si–Ti
  5. Experimental study of the phase equilibria of the Ni – Zr system
  6. Tensile behaviour of micro-sized copper wires studied using a novel fibre tensile module
  7. Dislocation densities in soft and hard oriented grains of compression deformed textured NiAl polycrystals
  8. The influence of plastic instabilities on the mechanical properties of a high-manganese austenitic FeMnC steel
  9. Modeling of isothermal bainite formation based on the nucleation kinetics
  10. Application of the Kaptay model in calculation of ternary liquid alloys' viscosities
  11. The influence of the austenite dispersion on phase transformation during the austempering of ductile cast iron having a dual matrix structure
  12. Effect of trace Ti on the microstructure and mechanical properties of AM50 alloy
  13. Applied
  14. Diffusion bonding of the Mo-base alloy TZM with interlayers
  15. Amorphization, nanocrystallization and magnetic properties of mechanically milled Sm–Co magnetic powders
  16. Wear behavior of plasma nitrided AISI 420 stainless steel
  17. Hot extrusion of α and α/β-brass alloys
  18. Role of surface texture and roughness parameters in friction and transfer layer formation under dry and lubricated sliding conditions
  19. The emergence and disappearance of a high density of microcracks in nitrided Fe-4.65 at.% Al alloy
  20. Notifications
  21. DGM News
https://doi.org/10.3139/146.101704
Schlagwörter für diesen Artikel
Magnesium alloy; Titanium; Grain refining; Microstructure; Mechanical properties

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Basic
  4. On the reaction scheme and liquidus surface in the ternary system Al–Si–Ti
  5. Experimental study of the phase equilibria of the Ni – Zr system
  6. Tensile behaviour of micro-sized copper wires studied using a novel fibre tensile module
  7. Dislocation densities in soft and hard oriented grains of compression deformed textured NiAl polycrystals
  8. The influence of plastic instabilities on the mechanical properties of a high-manganese austenitic FeMnC steel
  9. Modeling of isothermal bainite formation based on the nucleation kinetics
  10. Application of the Kaptay model in calculation of ternary liquid alloys' viscosities
  11. The influence of the austenite dispersion on phase transformation during the austempering of ductile cast iron having a dual matrix structure
  12. Effect of trace Ti on the microstructure and mechanical properties of AM50 alloy
  13. Applied
  14. Diffusion bonding of the Mo-base alloy TZM with interlayers
  15. Amorphization, nanocrystallization and magnetic properties of mechanically milled Sm–Co magnetic powders
  16. Wear behavior of plasma nitrided AISI 420 stainless steel
  17. Hot extrusion of α and α/β-brass alloys
  18. Role of surface texture and roughness parameters in friction and transfer layer formation under dry and lubricated sliding conditions
  19. The emergence and disappearance of a high density of microcracks in nitrided Fe-4.65 at.% Al alloy
  20. Notifications
  21. DGM News
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 22.9.2025 von https://www.degruyterbrill.com/document/doi/10.3139/146.101704/html
Button zum nach oben scrollen