Volume 53, Issue 5 - Special Issue: Biomechanics and Biomaterials in Oral Rehabilitation and Dental Treatment

The present paper provides an introduction to regular bone structure in the face area which is considered a precondition of successful implantation. The specific properties of the jaw bones have to be observed in this context. Bone is the largest calcium storage, forms part of the supporting tissue and displays distinctive plasticity and adaptability. Thus, an adequate, differentiated composition and metabolism are required. The bone matrix consists of organic and inorganic structures. The cells, osteoblasts, osteoclasts and osteocytes are responsible for bone formation, resorption and metabolism and, thus, for remodeling processes (formation and resorption) which permanently occur in bone tissue. Periosteum and endosteum form a functional unit with bone tissue itself and exercise protective, nutritive and growth functions.

The finite element (FE) method was originally developed on a physical basis for the computation of structure-mechanical problems. Meanwhile, it has been widely applied to medical issues. This study sought a suitable method to build a FE model for remodelling processes in osseous defects supplemented with bone substitute material. For this purpose, the second right premolars were extracted from four pig mandibles ( Sus scrofa domesticus ) and the extraction alveoli were provided with synthetic bone substitute material. After 70 days, a segmented osteotomy of this area was performed for specimen collection. Radiographs of the specimens were taken in defined planes before and after fixation and embedded with Technovit 9100. Fixation-related shrinkage was quantified from the radiographs using reference lines. Computer tomographic (CT) and microCT images of the fixed and embedded specimens were obtained. From these data, a FE model was built. The construction of a FE model is sufficient to represent bone remodelling after supply of bone substitute material. The use of microCT data permits building a clearly more precise model.

Sinus floor elevation is the standard procedure that allows dental implant insertion in the atrophic posterior maxilla. Instead of autogenous bone, tissue-engineered bone grafts can be used, but clear comparative clinical studies also assessing the influence of the biomaterial are missing. In six patients, tissue-engineered bone grafts were used in eight sinus floor elevations. After culturing osteoblast-like cells from biopsies of the maxilla, they were seeded on scaffolds made either from demineralised bovine bone matrix (DBBM) or from solvent-dehydrated mineralised bovine bone (SDBB), and grafted. In all patients primary wound healing was without complications, except for one patient in the SDBB group. After 12 months, implant insertion was possible only in the SDBB group; in the DBBM group, fibrous connective tissue was found in an attempt of implant insertion. After 5 months, implant placement was performed in one patient of each group. However, the two implants inserted in the DBBM group were lost after 6 weeks. Histology of the bone cores in the DBBM group at 5 months showed lamellar bone and osteoid, and at 12 months showed fibrous connective tissue. Inflammation and some resorption of the scaffold was found 5 months after SDBB grafting, and after 12 months cancellous bone formation encapsulating SDBB remnants were observed. These preliminary data suggest that the preparation method of the bovine bone matrix, in particular the mineral content, and therefore the mechanical stability may have some influence on the generation of new bone.

Bone substitution materials are seen as an alternative to autogenous bone transplants in the reconstruction of human bone structures. The aim of the present animal study was to evaluate the clinical handling and the conditions of bone healing after the application of a phosphoserine and collagen-I-modified calcium-phosphate cement (Biozement D). The application of phosphoserine is supposed to influence the texture of the extracellular matrix. Standardised bone defects were created in the lower jaw of 10 adult minipigs. These defects were reconstructed with a pasty calcium-phosphate cement mixture. After a healing time of 4 months, the animals were sacrificed. The mandibles of all animals were resected and non-decalcified histological sections of the areas of interest were prepared. The experiment was evaluated by means of qualitative histology and histomorphometry. The hydroxyapatite cement entirely hardened intraoperatively. Modelling and handling of the cement was facile and the margin fit to the host bone was excellent. Histology showed that resorption started in the periphery and proceeded exceptionally fast. The bony substitution, especially in phosphoserine-endowed cements, was very promising. After a healing period of 4 months, phosphoserine cements showed a bone regeneration of nearly two-thirds of the defect sizes. In the applied animal experiment, the newly developed hydroxyapatite collagen-I cement is well suited for bone substitution due to its easy handling, its excellent integration and good resorption characteristics. The addition of phosphoserine is very promising in terms of influencing resorption features and bone regeneration.

The design of a post and core restoration is a trade-off between a series of requirements to achieve stability of the post itself, the surrounding root dentine and the joint between tooth and post, while maintaining a sufficient apical seal of the remaining root canal filling. Post and core restoration systems come in a variety of different designs and dimensions, where each has its specific strength and weakness. With the exception of threaded versions, posts normally rely on either chemical and/or frictional locking between the post and the remaining root. Failure due to fatigue of the joint or root fracture due to overloading of the dentine is a frequent failure mode, especially for posts anchoring removable prostheses. Perforation of the root in an attempt to maximize the post length is a main cause for failure, too. A new design is proposed which uses a short but large diameter post. The risk of decementation is reduced by positive locking. A cavity with an undercut is prepared into the root, into which the post is fitted. Once joined, the post cannot be separated from the tooth without destruction of either the root or the post. The principle of the new design uses preparation tools and a post which is spread at the bottom. A cylindrically prepared hole is re-shaped to a defined inverse taper with the wider diameter at the bottom of the hole. A cylindrical post is inserted and spread at the bottom to a matching shape after placement. A first in vitro test of the stability showed that the positive locking provides at least as good extraction resistance as conventional post without the critical reliance on the luting/bonding agent.

Orthodontic miniscrews are exposed to three mechanical loading phases during clinical use: torsional loading upon insertion, flexural loading during anchorage function, and torsional loading upon removal. The aim of this study was to simulate clinical loading conditions for different types of orthodontic miniscrews in vitro to quantify the effects of combined torsional and bending stress. Various orthodontic miniscrew systems (Lomas, Dual-top, Aarhus anchorage, Tomas-pin and T.I.T.A.N.-pin) comprising 10 samples each were subjected to the following loading sequences in vitro : a torsional load corresponding to manual insertion with limited torque; and flexural loading at two different insertion depths. For all screw systems with torsional pre-loading (simulating insertion), subsequent flexural loading (simulating anchorage) yielded permanent deformations of approximately 0.15–0.25 mm, depending on the insertion depth. Since EDX analysis revealed comparable elemental compositions for the different screw systems, the differences in mechanical properties are attributed to screw design. Torsional loading during screw insertion may cause premature mechanical weakening and needs to be minimized. Unless fully inserted, screws show pronounced plastic deformation and hence fracture risk under subsequent flexural loading.

To assess the usefulness of different post and core materials and systems, in vitro testing of fracture strength and fatigue resistance is a useful tool. However, the literature does not present coherent results as to which system can withstand the highest loads. With a geometrical model, the effects of load angulation and contact point location on the generated forces were calculated. To validate the mathematical model, a set of measurements was performed with a set-up that made it possible to measure the critical forces on a post and core restoration. A high level of correlation between the predictions of the model and the measurements was found. It was shown that the resulting forces are strongly dependent on the precise design of the test set-up and results from different geometries cannot be compared directly. Very strong sensitivity to small misalignment was found, all of which serves to explain the large differences in the literature.

Human teeth with substantial coronal defects are subject to reconstruction by means of post-and-core restorations. Typically, such a restoration comprises a slightly cylindrical post onto which an abutment of varying shape, depending on the designated restoration, is attached. As clinical results are not satisfactory to date, a new post-and-core design which makes use of positive locking (rather than relying on chemical bonding agents for retention in the residual root) was proposed. Using proprietary burs, an inversely conical hole is machined into the root, into which the prefabricated post-and-core restoration is inserted. This part can be spread at the bottom to match the cavity's undercut form, resulting in a positive lock which can only be separated by destruction of root, restoration or both. Another key feature of this system is a ring/groove geometry which is able to absorb the wedging forces created by said spreading and the stress of loading of the restoration which arises from mascatory forces. To assess the properties, especially in terms of the stress imposed on the remaining tooth at highest possible loading, both finite element simulations and in vitro failure tests were performed and the findings compared. The results suggest that the parameters of the finite element simulations are in good agreement with reality. As calculated and measured force levels immediately before failure of the restoration are high, the introduced new geometry has significant advantages over the classical restoration.

Human teeth with substantial coronal defects are subject to reconstruction by means of post and core restorations. Typically, such a restoration comprises a slightly cylindrical post onto which an abutment of varying shape, depending on the designated restoration, is attached. As clinical results are not satisfactory to date, we proposed a new proprietary post and core design which makes use of positive locking. As this prefabricated system is not customised to an individual root's cross-sectional geometry (usually oval), a varying amount of radicular dentin is left in periphery of the core's outer edge. The aim of this study was to assess the implications of this fact, i.e., whether the root has to endure higher overall stress levels which ultimately may lead to failure of one of the components involved. A series of finite element simulations were performed to evaluate stress and strain on the system, in which the proposed post and core was embedded into a virtual dentin cylinder of different diameters, ranging from flush mounting of the restoration to a dentin excess of 4 mm, and subsequently loaded with forces with two angles of attack (90° and 130°). The results show that flush mounting yields an agreeable stress and strain distribution within the radicular dentin, but overall stress levels drop significantly with an excess of 0.5 mm of surrounding dentin. More than 1 mm excess was not found to have profound positive effects.

Clinical methods of investigation, such as tooth colour determination, should be simple, quick and reproducible. The determination of tooth colours usually relies upon manual comparison of a patient's tooth colour with a colour ring. After some days, however, measurement results frequently lack unequivocal reproducibility. This study aimed to examine an electronic method for reliable colour measurement. The colours of the teeth 14 to 24 were determined by three different examiners in 10 subjects using the colour measuring device Shade Inspector™. In total, 12 measurements per tooth were taken. Two measurement time points were scheduled to be taken, namely at study onset ( T 1 ) and after 6 months ( T 2 ). At either time point, two measurement series per subject were taken by the different examiners at 2-week intervals. The inter-examiner and intra-examiner agreement of the measurement results was assessed. The concordance for lightness and colour intensity (saturation) was represented by the intra-class correlation coefficient. The categorical variable colour shade (hue) was assessed using the kappa statistic. The study results show that tooth colour can be measured independently of the examiner. Good agreement was found between the examiners.