Influence of Mold Temperature on the Internal Structure and Creep Variation in the Thickness Direction of sPS Injection Moldings

References

Ishihara, N., et al., “Crystalline Syndiotactic Polystyrene”, Macromolecules, 19, 2464–2465 (1986)10.1021/ma00163a027Suche in Google Scholar

Shan, C. L. P., et al., “Conversion Studies in a Novel Reaction Injection Molding Process for Syndiotactic Polystyrene”, J. Appl. Polym. Sci., 70, 2679–2693 (1998)10.1002/(SICI)1097-4628(19981226)70:13<2679::AID-APP13>3.0.CO;2-JSuche in Google Scholar

Hieber, C. A., “Correlating the Crystallization Kinetics of Syndiotactic Polystyrene”, J. Appl. Polym. Sci., 91, 2402–2406 (2004)10.1002/app.13399Suche in Google Scholar

Ulcer, Y., et al., “Structural Gradients Developed in Injection-molded Syndiotactic Polystyrene (sPS)”, J. Appl. Polym. Sci., 60, 669–61 (1996)10.1002/(SICI)1097-4628(19960502)60:5<669::AID-APP4>3.0.CO;2-OSuche in Google Scholar

Hong, M.-H., White, J. L., “Structure development in melt-spinning syndiotactic polystyrene and comparison to atactic polystyrene”, Polym. Eng. Sci., 44, 2141–2147 (2004)10.1002/pen.20220Suche in Google Scholar

Banik, K., Mennig, G., “Process-induced Long-term Deformation Behavior of Semi-crystalline PBT”, Polym. Eng. Sci., 46, 882–888 (2006)10.1002/pen.20494Suche in Google Scholar

Engelsing, K., Einfluß des freien Volumens auf das verarbeitungsabhängige Deformationsverhalten spritzgegossener amorpher Thermoplaste, Ph.D Thesis, Technische Universität Chemnitz, Germany (2000)Suche in Google Scholar

Pötsch, G., Michaeli, W., Injection Molding: An Introduction, Hanser Publishers, Munich (1995)Suche in Google Scholar

Potente, H., Schnieders, J., “Influence of Process Parameters on the Phenomenon of Stress Cracking during Hot Plate Welding”, J. Reinf. Plast. Compos., 21, 489–496 (2002)10.1177/0731684402021006828Suche in Google Scholar

Takeshima, M., Funakoshi, N., “Molecular Orientation Distribution in Injection-molded Polycarbonate Discs”, J. Appl. Polym. Sci., 32, 3457–3468 (1986)10.1002/app.1986.070320209Suche in Google Scholar

Hsiung, C. M., Cakmak, M., “Effect of Processing Conditions on the Structural Gradients developed in Injection-molded Poly(aryl ether ketone) (PAEK) parts. I. Characterization by Microbeam X-ray Diffraction Technique”, J. Appl. Polym. Sci., 47, 125–147 (1993)10.1002/app.1993.070470116Suche in Google Scholar

Hsiung, C. M., Cakmak, M., “Effect of Injection-molding Conditions on the Crystallinity, Orientation Gradients, and Mechanical Properties of Poly(aryl ether ketone). II. Large Dumbbell Parts”, J. Appl. Polym. Sci., 47, 149–165 (1993)10.1002/app.1993.070470117Suche in Google Scholar

Banik, K., Process-induced Long-term Deformation Behavior of Injection Molded Semicrystalline Thermoplastics, Ph.D Thesis, Technische Universität Chemnitz, Germany (2006)10.1002/pen.20494Suche in Google Scholar

Shibaya, M., et al., “Effect of Mold Temperature on Structure and Property Variations of PBT Injection Moldings in the Thickness Direction”, Int. Polym. Proc., 19, 303–307 (2004)Suche in Google Scholar

Nguyen-Chung, T., Mennig, G., “Mechanismen der Molekülorientierungen in spritzgegossenen Kunststoff-Bauteilen”, Technomer Proceedings, 19, 155–156 (2005)Suche in Google Scholar

Nguyen-Chung, T., Mennig, G., “Does fountain flow influence molecular orientation in injection moulded parts?”, Plast. Rubber Comp.,: Macromolecular Engineering, 35, 418–424 (2006)10.1179/174328906X149709Suche in Google Scholar

Engelsing, K., Mennig, G., “Influence of the Injection Molding Process on the Free Volume and Its Effect on the Creep Behavior of Styrene-Acrylonitrile Copolymer”, Mech. Time-Depend. Mater., 5, 27–38 (2001)10.1023/A:1009858702188Suche in Google Scholar