Home Technology Abrasive wear resistance of modified X37CrMoV5-1 hot work tool steel after conventional and laser heat treatment
Article
Licensed
Unlicensed Requires Authentication

Abrasive wear resistance of modified X37CrMoV5-1 hot work tool steel after conventional and laser heat treatment

  • Martin Šebek , Ladislav Falat , Martin Orečný , Ivan Petryshynets , František Kováč and Martin Černík
Published/Copyright: April 28, 2018
Become an author with De Gruyter Brill
Submit Manuscript Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 109 Issue 5

Abstract

The effects of two conventional heat treatments and one innovative processing by laser surface remelting of modified X37CrMoV5-1 tool steel on its abrasion wear resistance were investigated. Conventional heat treatments consisted of quenching from 990 °C, individually followed by two different tempering treatments to achieve secondary hardness either at 520 °C or 560 °C. Laser surface remelting was performed using optimized parameters of continuous laser beam scanning mode. The results showed that the highest wear resistance was obtained for almost carbide-free, surface remelted microstructure with the highest hardness due to microstructural refinement and martensitic transformation hardening. The observed differences in wear resistance among individual material states are discussed in relation to their microstructures, hardness, and wear mechanisms characteristics.

Keywords: Modified tool steel; Abrasive wear; Heat treatment; Laser surface remelting; Hardness
*Correspondence address, Dr. Ladislav Falat, Institute of Materials Research SAS, Watsonova 47, 04001 Košice, Slovakia, Tel.: +421557922447, Fax: +421557922408, E-mail:

References

[1] M.Hawryluk, M.Zwierzchowski, M.Marciniak, P.Sadowski: Eng. Fail. Anal.79 (2017) 313–329. 10.1016/j.engfailanal.2017.04.036Search in Google Scholar

[2] S.G.Sapate, A.D.Chopde, P.M.Nimbalkar, D.M.Chandarkar: Mater. Des.28 (2007) 1923–1927. 10.1016/j.matdes.2007.02.014Search in Google Scholar

[3] P.J.Blau, R.R.Dehoff: Wear302 (2013) 1035–1039. 10.1016/j.wear.2012.11.040Search in Google Scholar

[4] X.T.Deng, Z.D.Wang, Y.Han, H.Zhao, G.D.Wang: J. Iron Steel Res.21 (2014) 98–103. 10.1016/S1006-706X(14)60015-7Search in Google Scholar

[5] R.Máscia, F.F.Ramos Neto, T.F.Barbosa Neto, S.D.Franco: Wear303 (2013) 412–418. 10.1016/j.wear.2013.03.037Search in Google Scholar

[6] S.D.Bakshi, H.K.D.H.Bhadeshia, P.H.Shipway: Wear308 (2013) 46–53. 10.1016/j.wear.2013.09.008Search in Google Scholar

[7] K.Singh, R.K.Khatirkar, S.G.Sapate: Wear328–329 (2015) 206–216. 10.1016/j.wear.2015.02.019Search in Google Scholar

[8] I.Gunes, M.Uzun, A.Cetin, K.Aslantas, A.Cicek: Kovove Mater.54 (2016) 195–204. 10.4149/km_2016_3_195Search in Google Scholar

[9] D.Jandová, P.Šuchmann, J.Nižňanská: Key Eng. Mater.647 (2015) 23–37. 10.4028/www.scientific.net/KEM.647.23;Search in Google Scholar

[10] J.Preußner, S.Oeser, W.Pfeiffer, A.Temmler, E.Willenborg: Int. J. Mater. Res.105 (2014) 328–336. 10.3139/146.111027Search in Google Scholar

[11] M.C.Oh, H.Yeom, Y.Jeon, B.Ahn: Arch. Metall. Mater.60, (2015) 1331–1334. 10.1515/amm-2015-0125Search in Google Scholar

[12] D.A.Lesyk, S.Martinez, V.V.Dzhemelinskyy, A.Lamikiz, B.N.Mordyuk, G.I.Prokopenko: Surf. Coatings Technol.278 (2015) 108–120. 10.1016/j.surfcoat.2015.07.049Search in Google Scholar

[13] C.T.Kowk, F.T.Cheng, H.C.Man: Surf. Coatings Technol.202 (2007), 336–348. 10.1016/j.surfcoat.2007.05.085Search in Google Scholar

[14] M.Li, Y.Wang, B.Han, W.Zhao, T.Han: Appl. Surf. Sci.255 (2009) 7574–7579. 10.1016/j.apsusc.2009.04.030Search in Google Scholar

[15] K.Labisz, T.Tański, M.Kremzer, D.Janicki: Int. J. Mater. Res.108 (2017) 126–132. 10.3139/146.111456Search in Google Scholar

[16] Q.-Y.Ma, X.Gao, J.-Q.Li: Kovove Mater.55 (2017) 45–50. 10.4149/km_2017_1_45Search in Google Scholar

[17] T.Simsek, M.Baris, A.Akkurt: Int. J. Mater. Res.108 (2017) 486–494. 10.3139/146.111497Search in Google Scholar

[18] R.Colaco, R.Vilar: Wear258 (2005) 225–231. 10.1016/j.wear.2004.09.029Search in Google Scholar

[19] N.Mebarki, P.Lamesle, D.Delagnes, C.Levaillant, F.Delmas, in: J.Bergstrom, G.Fredriksson, M.Johansson, O.Kotik, F.Thuvander (Eds.), Proc. of the 6th International Tooling Conference. The use of tool steel: Experience and research. Karlstad University, Sweden (2002) 617.Search in Google Scholar

[20] D.Delagnes, P.Lamesle, M.H.Mathon, N.Mebarki, C.Levaillant: Mater. Sci. Eng. A.394 (2005) 435–444. 10.1016/j.msea.2004.11.050Search in Google Scholar

[21] A.Ning, W.Mao, X.Chen, H.Guo, J.Guo: Metals7 (2017) 70. 10.3390/met7030070Search in Google Scholar

[22] H.K.Moon, K.B.Lee, H.Kwon: Mater. Sci. Eng. A.474 (2008) 328–334. 10.1016/j.msea.2007.04.014Search in Google Scholar

[23] http://www.uddeholm.com/files/PB_Uddeholm_vidar_superior_english.pdfSearch in Google Scholar

[24] A.C.P.Rodrigues, P.J.N.Ribeiro, W.Österle, C.R.F.Azevedo: Eng. Fail. Anal.56 (2015) 131–141. 10.1016/j.engfailanal.2015.03.011Search in Google Scholar

[25] R.Colaco, R.Vilar: Stabilization of retained austenite in laser surface melted tool steels, Mater. Sci. Eng. A.385 (2004) 123–127. 10.1016/j.msea.2004.06.069Search in Google Scholar

[26] L.Falat, J.Kepič, L.Čiripová, P.Ševc, I.Dlouhý: J. Mater. Res.31 (2016) 1532–1543. 10.1557/jmr.2016.134Search in Google Scholar

[27] C.R.F.Azevedo, A.Sinatora: Eng. Fail. Anal.11 (2004) 829–841. 10.1016/j.engfailanal.2004.03.003Search in Google Scholar

[28] M.Lindroos, K.Valtonen, A.Kemppainen, A.Laukkanen, K.Holmberg, V.T.Kuokkala: Wear322–323 (2015) 32–40. 10.1016/j.wear.2014.10.018Search in Google Scholar

Received: 2017-11-02
Accepted: 2017-12-18
Published Online: 2018-04-28
Published in Print: 2018-05-15

© 2018, Carl Hanser Verlag, München

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. Manufacturing of functionally graded metal matrix composite materials by segregation
  5. Indenter size effect in high-pressure torsion deformed Pd-based metallic glass
  6. Investigation of the effect of bath temperature on the bath–freeze lining interface temperature in the CuOx–FeOy–MgO–SiO2 system at copper metal saturation
  7. Decomposition of Al4O4C in the presence of C at high temperatures in vacuum
  8. Optical and magnetic properties of diluted magnetic semiconductor Zn0.95M0.05S nanorods prepared by a hydrothermal method
  9. Structural, magnetic and optical properties of Al-substituted nickel ferrite nanoparticles
  10. Effect of processing parameters on microstructural and mechanical properties of aluminum–SiO2 nanocomposites produced by spark plasma sintering
  11. Sn-bonded LaFe11.6Si1.4Hy magnetocaloric composites with a 3-d Ni-coating steel substrate formed by hot-pressing
  12. Effect of laser energy density on microstructures and mechanical properties of selective laser melted Ti-6Al-4V alloy
  13. Structure and corrosion resistance of titanium oxide layers produced on NiTi alloy in low-temperature plasma
  14. Severe shot peening of AISI 321 with 1 000 % and 1 300 % coverages: A comparative study on the surface nanocrystallization, phase transformation, sub-surface microcracks, and microhardness
  15. Abrasive wear resistance of modified X37CrMoV5-1 hot work tool steel after conventional and laser heat treatment
  16. Effect of coupled annular electromagnetic stirring and intercooling on the microstructures, macrosegregation and properties of large-sized 2219 aluminum alloy billets
  17. People
  18. Otmar Vöhringer on the occasion of his 80th birthday
  19. In Memory of Lasar Simhovich Shvindlerman (September 20th, 1935–March 3rd, 2018)
  20. In Memory of Prof. Dr.-Ing. Heinrich Wollenberger
  21. DGM News
  22. DGM News
https://doi.org/10.3139/146.111624
Keywords for this article
Modified tool steel; Abrasive wear; Heat treatment; Laser surface remelting; Hardness

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. Manufacturing of functionally graded metal matrix composite materials by segregation
  5. Indenter size effect in high-pressure torsion deformed Pd-based metallic glass
  6. Investigation of the effect of bath temperature on the bath–freeze lining interface temperature in the CuOx–FeOy–MgO–SiO2 system at copper metal saturation
  7. Decomposition of Al4O4C in the presence of C at high temperatures in vacuum
  8. Optical and magnetic properties of diluted magnetic semiconductor Zn0.95M0.05S nanorods prepared by a hydrothermal method
  9. Structural, magnetic and optical properties of Al-substituted nickel ferrite nanoparticles
  10. Effect of processing parameters on microstructural and mechanical properties of aluminum–SiO2 nanocomposites produced by spark plasma sintering
  11. Sn-bonded LaFe11.6Si1.4Hy magnetocaloric composites with a 3-d Ni-coating steel substrate formed by hot-pressing
  12. Effect of laser energy density on microstructures and mechanical properties of selective laser melted Ti-6Al-4V alloy
  13. Structure and corrosion resistance of titanium oxide layers produced on NiTi alloy in low-temperature plasma
  14. Severe shot peening of AISI 321 with 1 000 % and 1 300 % coverages: A comparative study on the surface nanocrystallization, phase transformation, sub-surface microcracks, and microhardness
  15. Abrasive wear resistance of modified X37CrMoV5-1 hot work tool steel after conventional and laser heat treatment
  16. Effect of coupled annular electromagnetic stirring and intercooling on the microstructures, macrosegregation and properties of large-sized 2219 aluminum alloy billets
  17. People
  18. Otmar Vöhringer on the occasion of his 80th birthday
  19. In Memory of Lasar Simhovich Shvindlerman (September 20th, 1935–March 3rd, 2018)
  20. In Memory of Prof. Dr.-Ing. Heinrich Wollenberger
  21. DGM News
  22. DGM News
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2026 De Gruyter Brill
Downloaded on 24.2.2026 from https://www.degruyterbrill.com/document/doi/10.3139/146.111624/html
Scroll to top button