Startseite Effects of contact pressure and sliding distance on the lubricated friction and wear properties of Zn-25Al-3Cu alloy: A comparative study with SAE 65 bronze
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Effects of contact pressure and sliding distance on the lubricated friction and wear properties of Zn-25Al-3Cu alloy: A comparative study with SAE 65 bronze

  • Temel Savaşkan , Hasan Onur Tan und Reza Anvari Maleki
Veröffentlicht/Copyright: 15. Oktober 2015
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 106 Heft 10

Abstract

Lubricated friction and wear properties of Zn-25Al-3Cu alloy were investigated in comparison with SAE 65 bronze over a range of contact pressure (1–8 MPa) and sliding distance (0–80 km) using a block-on-disc type test machine. The friction coefficients of the alloy and the bronze decreased, but their working temperature and wear volume increased with contact pressure. Their friction coefficient and the working temperature showed opposite changes with sliding distance before they reached steady-state levels. However, the wear volume of both the alloy and the bronze increased continuously with sliding distance. Although the hardness and compressive strength of the alloy were lower than those of the bronze, it exhibited higher wear resistance. This was related to their wear behaviour since smearing played a great role in the wear of the alloy while abrasion dominated the wear of the bronze.

Keywords: Zn-25Al-3Cu alloy; SAE 65 bearing bronze; Lubricated friction; Wear; Wear mechanisms
*Correspondence address, Prof. Dr. Temel Savaşkan, Department of Mechanical Engineering, Karadeniz Technical University, 61080 Trabzon, Turkey, Tel.: +904623773275, Fax: +904623773336, E-mail:

References

[1] E.Gebhardt: Z. Metallkd. 32 (1940) 78.Suche in Google Scholar

[2] K.Löhberg: Z. Metallkd. 32 (1940) 86.Suche in Google Scholar

[3] W.Köster, K.Moeller: Z. Metallkd. 33 (1941) 278.Suche in Google Scholar

[4] W.Köster, K.Moeller: Z. Metallkd. 33 (1941) 284.Suche in Google Scholar

[5] W.Köster: Z. Metallkd. 33 (1941) 289.Suche in Google Scholar

[6] E.Gebhardt: Z. Metallkd. 34 (1942) 208.Suche in Google Scholar

[7] E.Gebhardt: Z. Metallkd. 40 (1949) 136.Suche in Google Scholar

[8] W.Mihaichuk: Machine Des. 53 (1981) 133.Suche in Google Scholar

[9] T.Calayag, D.Ferres: Proc. Earthmoving Industry Conference, USA (1982).Suche in Google Scholar

[10] F.E.Goodwin, A.L.Ponikvar: Engineering Properties of Zinc Alloys, International Lead Zinc Research Organization, USA (1989).Suche in Google Scholar

[11] E.Gervais, H.Levert, M.Bess: AFS Trans. 68 (1980) 183.Suche in Google Scholar

[12] A.F.Skenazi, J.Pelerin, D.Coutsouradis, B.Magnus: Z. Metallkd. 37 (1983) 898.Suche in Google Scholar

[13] T.S.Calayag: Mod. Cast. 74 (1984) 19.Suche in Google Scholar

[14] E.Gervais, R.J.Barnhurst, C.A.Loong: JOM37 (1985) 43. 10.1007/BF03257680Suche in Google Scholar

[15] P.P.Lee, T.Savaşkan, E.Laufer: Wear117 (1987) 79. 10.1016/0043-1648(87)90245-6Suche in Google Scholar

[16] T.Savaşkan, A.Aydıner: Wear257 (2004) 377. 10.1016/j.wear.2004.01.007Suche in Google Scholar

[17] T.Savaşkan, O.Bican: Mater. Sci. Eng. A-Struct. 404 (2005) 259. 10.1016/j.msea.2005.05.078Suche in Google Scholar

[18] T.Savaşkan, Z.Azaklı: Wear264 (2008) 920. 10.1016/j.wear.2007.06.008Suche in Google Scholar

[19] B.K.Prasad: Mater. Charact. 44 (2000) 301. 10.1016/S1044-5803(99)00057-1Suche in Google Scholar

[20] B.K.Prasad: Wear254 (2003) 35. 10.1016/S0043-1648(02)00303-4Suche in Google Scholar

[21] B.K.Prasad: Tribol. Lett. 25 (2007) 103. 10.1007/s11249-006-9054-3Suche in Google Scholar

[22] B.K.Prasad, O.P.Modi, A.H.Yegneswaran: Wear264 (2008) 990. 10.1016/j.wear.2007.08.003Suche in Google Scholar

[23] T.Savaşkan, S.Murphy: Pract. Metallogr. 24 (1987) 204.10.1515/pm-1987-240503Suche in Google Scholar

[24] T.Savaşkan, S.Murphy: Wear116 (1987) 211. 10.1016/0043-1648(87)90183-9Suche in Google Scholar

[25] A.Vencl, I.Bobic, F.Vucetic, B.Bobic, J.Ruzic: Mater. Des. 64 (2014) 381. 10.1016/j.matdes.2014.07.056Suche in Google Scholar

[26] T.Savaşkan, R.A.Maleki: Tribol. Trans. 57 (2014) 435. 10.1080/10402004.2014.880540Suche in Google Scholar

[27] T.Savaşkan, O.Bican: Tribol. Lett. 40 (2010) 327. 10.1007/s11249-010-9667-4Suche in Google Scholar

[28] T.Savaşkan, O.Bican: Tribol. Lett. 37 (2010) 175. 10.1007/s11249-009-9509-4Suche in Google Scholar

[29] T.Savaşkan, R.A.Maleki, H.O.Tan: Tribol. Int. 81 (2015) 105. 10.1016/j.triboint.2014.08.014Suche in Google Scholar

[30] A.P.Hekimoğlu, T.Savaşkan: Int. J. Mater. Res. 105 (2014) 1084. 10.3139/146.111116Suche in Google Scholar

[31] J.Halling (Ed.): Principles of Tribology, 1st Ed., Macmillan Education Ltd., London (1975).Suche in Google Scholar

[32] I.M.Hutchings: Tribology: Friction and Wear of Engineering Materials, Edward Arnold, London (1992). 10.1016/0301-679X(92)90055-RSuche in Google Scholar

[33] F.W.Bowden, D.Tabor: The Friction and Lubrication of Solids, Clarendon Press, Oxford (2001).Suche in Google Scholar

[34] T.Savaşkan, G.Pürçek, S.Murphy: Wear252 (2002) 693. 10.1016/S0043-1648(01)00876-6Suche in Google Scholar

[35] A.H.Cottrell: An Introduction to Metallurgy, Edward Arnold, London (1975).Suche in Google Scholar

[36] W.D.Callister: Materials Science and Engineering, 7th Ed., John Wiley & Sons, Inc., New York (2007).Suche in Google Scholar

[37] H.A.Avner: Introduction to Physical Metallurgy, International edition, McGraw-Hill Book Company, New York (1974).Suche in Google Scholar

Received: 2015-04-06
Accepted: 2015-06-09
Published Online: 2015-10-15
Published in Print: 2015-10-14

© 2015, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Original Contributions
  4. On the widths of the hysteresis of mechanically and thermally induced martensitic transformations in Ni–Ti-based shape memory alloys
  5. The effects of external compressive stress on the kinetics of low temperature bainitic transformation and microstructure in a superbainite steel
  6. The effect of compressing pressure on the microstructure and properties of W-10 wt.% Cu composite
  7. Simulation of dendritic growth of Al-4 wt.% Cu alloy from an undercooled melt
  8. Effects of contact pressure and sliding distance on the lubricated friction and wear properties of Zn-25Al-3Cu alloy: A comparative study with SAE 65 bronze
  9. Electrochemical behaviour of stainless steel in acidic fluoride media
  10. Quick fabrication of appropriate morphology and composition CoFe films with desirable microwave properties
  11. Piezo-absorbing effect of microwave absorbing composites with carbonyl iron particles as the filler
  12. Nanocomposite based on polyaniline emeraldine-base and α-Al2O3: A structural characterization
  13. Effect of Cr3C2 content on the microstructure and properties of Mo2NiB2-based cermets
  14. Short Contributions
  15. Damage mechanisms in aluminum-matrix composites reinforced with nano-alumina particles
  16. Synthesis of ultrafine powder of vanadium carbide V8C7 by microwave heating
  17. People
  18. Prof. Dr. Werner Skrotzki on the occasion of his 65th birthday
  19. DGM News
  20. DGM News
https://doi.org/10.3139/146.111282
Schlagwörter für diesen Artikel
Zn-25Al-3Cu alloy; SAE 65 bearing bronze; Lubricated friction; Wear; Wear mechanisms

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Original Contributions
  4. On the widths of the hysteresis of mechanically and thermally induced martensitic transformations in Ni–Ti-based shape memory alloys
  5. The effects of external compressive stress on the kinetics of low temperature bainitic transformation and microstructure in a superbainite steel
  6. The effect of compressing pressure on the microstructure and properties of W-10 wt.% Cu composite
  7. Simulation of dendritic growth of Al-4 wt.% Cu alloy from an undercooled melt
  8. Effects of contact pressure and sliding distance on the lubricated friction and wear properties of Zn-25Al-3Cu alloy: A comparative study with SAE 65 bronze
  9. Electrochemical behaviour of stainless steel in acidic fluoride media
  10. Quick fabrication of appropriate morphology and composition CoFe films with desirable microwave properties
  11. Piezo-absorbing effect of microwave absorbing composites with carbonyl iron particles as the filler
  12. Nanocomposite based on polyaniline emeraldine-base and α-Al2O3: A structural characterization
  13. Effect of Cr3C2 content on the microstructure and properties of Mo2NiB2-based cermets
  14. Short Contributions
  15. Damage mechanisms in aluminum-matrix composites reinforced with nano-alumina particles
  16. Synthesis of ultrafine powder of vanadium carbide V8C7 by microwave heating
  17. People
  18. Prof. Dr. Werner Skrotzki on the occasion of his 65th birthday
  19. DGM News
  20. DGM News
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 9.10.2025 von https://www.degruyterbrill.com/document/doi/10.3139/146.111282/html
Button zum nach oben scrollen