Home Technology Excellent cold rollability in a single pass of an Mg-4Er (wt.%) alloy
Article
Licensed
Unlicensed Requires Authentication

Excellent cold rollability in a single pass of an Mg-4Er (wt.%) alloy

  • X. H. Du , M. Hong , G. S. Duan , C. B. Wei , E. P. Jiang , M. Zhang , B. L. Wu , Y. D. Zhang and C. Esling
Published/Copyright: January 7, 2015
Become an author with De Gruyter Brill
Submit Manuscript Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 106 Issue 1

Abstract

Sheets of Mg-4Er (wt.%) alloy were prepared by multi-pass hot rolling and subsequent annealing. The annealed sheets could be cold-rolled to a high reduction of 95% (corresponding to a rolling strain of 3) by one-pass rolling at room temperature. The evolution of the deformed microstructure of Mg-4Er alloy was investigated during the cold-rolling process. The results suggest that multiple dislocation slips are the predominant deformation mode responsible for the remarkable rolling plastic strain. Meanwhile, the multiple dislocation slips are favorable to a continuous restoration process, which can accommodate the rolling strain by absorbing the deformation energy.

Keywords: Mg–Er alloy; Cold rolling; High strain rate; Rollability; Microstructure
* Correspondence address, Professor Baolin Wu, School of Materials Science and Engineering, Shenyang Aerospace University, South Avenue of Daoyi, 110136, Shenyang, China. Tel.: +86-24-89728701, Fax: +86-24-89728729, E-mail:

References

[1] P.Menzen, in: A.Beck (Ed.), The Technology of Magnesium and Its Alloys, F.A Hughes and Co. Ltd., London (1940).Search in Google Scholar

[2] J.C.McDonald: Trans. Metall. Soc. AIME212 (1958) 45.Search in Google Scholar

[3] S.L.Couling, J.F.Pashak, L.Sturkey: Trans. ASM51 (1959) 94.Search in Google Scholar

[4] M.R.Barnett, M.D.Nave, C.J.Bettles: Mater. Sci. Eng. A386 (2004) 205. 10.1016/S0921-5093(04)00942-6Search in Google Scholar

[5] M.T.Pérez-Prado, J.A.Del Valle, J.M.Contreras, O.A.Ruano: Scr. Mater.50 (2004) 661. 10.1016/j.scriptamat.2003.11.014Search in Google Scholar

[6] C.I.Chang, X.H.Du, J.C.Huang: Scr. Mater.57 (2007) 209. 10.1016/j.scriptamat.2007.04.007Search in Google Scholar

[7] M.T.Pérez-Prado, J.A.Del Valle, O.A.Ruano: Scr. Mater.51 (2004) 1093. 10.1016/j.scriptamat.2004.07.028Search in Google Scholar

[8] R.Z.Valiev, R.K.Islamgaliev, I.V.Alexandrov: Prog. Mater. Sci.45 (2000) 103. 10.1016/S0079-6425(99)00007-9Search in Google Scholar

[9] S.Q.Zhu, H.G.Yan, J.H.Chen, Y.Z.Wu, J.Z.Liu, J.Tian: Scr. Mater.63 (2010) 985. 10.1016/j.scriptamat.2010.02.005Search in Google Scholar

[10] S.Q.Zhu, H.G.Yan, J.H.Chen, Y.Z.Wu, Y.G.Du, X.Z.Liao: Mater. Sci. Eng. A559 (2013) 765. 10.1016/j.msea.2012.09.022Search in Google Scholar

[11] K.Xia, J.T.Wang, X.Wu, G.Chen, M.Gurvan: Mater. Sci. Eng. A410–411 (2005) 324. 10.1016/j.msea.2005.08.123Search in Google Scholar

[12] G.F.Lima, M.R.M.Triques, C.S.Kiminami, W.J.Botta, A.M.JorgeJr: J. Alloys Compd.15 (2014) s405. 10.1016/j.jallcom.2013.03.106Search in Google Scholar

[13] B.L.Wu, G.Wan, X.H.Du, Y.D.Zhang, F.Wagner, C.Esling: Mater. Sci. Eng. A573 (2013) 205. 10.1016/j.msea.2013.02.048Search in Google Scholar

[14] S.R.Agnew, M.H.Yoo, C.N.Tomé: Acta Mater.49 (2001) 4277. 10.1016/S1359-6454(01)00297-XSearch in Google Scholar

[15] E.W.Kelly, W.F.Hosford: Trans AIME242 (1968) 654.Search in Google Scholar

[16] A.D.Rollet, S.L.Wright. In: U.F.Kocks, C.N.Tomé, H.R.Wenk (Eds.): Texture and Anisotropy (1998).Search in Google Scholar

[17] H.K.Lin, J.C.Huang, T.G.Landon: Mater. Sci. Eng. A402 (2005) 250. 10.1016/j.msea.2005.04.018Search in Google Scholar

[18] M.Eddahbi, J.A.del Valle, M.T.Pérez-Prado, O.A.Ruano: Mater. Sci. Eng. A410 (2005) 308. 10.1016/j.msea.2005.08.081Search in Google Scholar

[19] C.I.Chang, X.H.Du, J.C.Huang: Scr. Mater.59 (2008) 356. 10.1016/j.scriptamat.2008.03.011Search in Google Scholar

[20] L.Lu, M.L.Sui, K.Lu: Science287 (2000) 1463. 10.1126/science.287.5457.1463Search in Google Scholar

[21] A.Styczynski, C.Hartig, J.Bohlen, D.Letzig: Scr. Mater.50 (2004) 943. 10.1016/j.scriptamat.2004.01.010Search in Google Scholar

[22] A.Galiyev, R.Kaibyshev, T.Sakai: Mater. Sci. Forum419-422 (2003) 509. 10.4028/www.scientific.net/MSF.419-422.509Search in Google Scholar

[23] R.Kaibyshev, O.Sitdikov: Z. Metallkd.85 (1994) 738.Search in Google Scholar

[24] A.G.Beer, M.R.Barnett: Mater. Sci. Eng. A423 (2006) 292. 10.1016/j.msea.2006.02.041Search in Google Scholar

[25] A.Kelly, G.W.Groves, P.Kidd: Crystallography and Crystal Defects, John Wiley & Sons Ltd., Chichester, England (2000).Search in Google Scholar

[26] A.Galiyev, R.Kaibyshev, G.Gottstein: Acta Mater.49 (2001) 1199. 10.1016/S1359-6454(01)00020-9Search in Google Scholar

[27] M.E.Kassner, S.R.Barrabes: Mater. Sci. Eng. A410–411 (2005) 152. 10.1016/j.msea.2005.08.052Search in Google Scholar

[28] J.Koike, T.Kobayashi, T.Mukai, H.Watanabe, M.Suzuki, K.Maruyama, K.Higashi: Acta Mater.51 (2003) 2055. 10.1016/S1359-6454(03)00005-3Search in Google Scholar

[29] J.Hadorn, R.P.Mulay, K.Hantzsche, S.Yi, J.Bohlen, D.Letzig, S.R.Agnew: Metall. Mater. Trans. A43 (2012) 1363. 10.1007/s11661-011-0923-5Search in Google Scholar

[30] Y.Chino, M.Kado, M.Mabuchi: Acta Mater.56 (2008) 387. 10.1016/j.actamat.2007.09.002Search in Google Scholar

[31] S.Sandlöbes, M.Friák, S.Zaefferer, A.Dick, S.Yi, D.Letzig, Z.Pei, L.-F.Zhu, J.Neugebauer, D.Raabe: Acta Mater.60 (2012) 3011. 10.1016/j.actamat.2012.02.006Search in Google Scholar

Received: 2014-03-02
Accepted: 2014-08-10
Published Online: 2015-01-07
Published in Print: 2015-01-09

© 2015, Carl Hanser Verlag, München

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. A novel roll-bonding methodology for the cross-scale analysis of phase properties and interactions in multiphase structural materials
  5. Excellent cold rollability in a single pass of an Mg-4Er (wt.%) alloy
  6. An experimental study of the precipitation kinetics of pre-rolled Ni-Span-C 902 superalloy
  7. Influences of high temperature on the microstructural, electrical and mechanical properties of Ni-23 wt.% Al alloy
  8. Investigation of the wear resistance and microstructure of Al/SiC metal matrix composites as a function of reinforcement volume fraction and reinforcement to matrix particle size ratio applying artificial neural network
  9. Influence of zinc (II) ion concentration on Ni–Zn–P coatings deposited onto aluminum and their corrosion behavior
  10. Joining steel to aluminum alloy by resistance spot welding with a rivet
  11. Electrophysical and structure-sensitive properties of liquid Ga–In alloys
  12. Short Communications
  13. Synthesis and characterization of the novel nanocomposite Co(OH)2/graphene as supercapacitor materials
  14. Preparation of MnAlC flakes by surfactant-assisted ball-milling and the effects of annealing
  15. An improved two-stage sintering method for tungsten heavy alloys: conventional solid-phase sintering followed by microwave heating
  16. Effect of excess Pb on ferroelectric characteristics of conductive Al-doped ZnO and Sn-doped In2O3 top electrodes in PbLaZrTiOx capacitors
  17. Effects of La–Zn substituent and calcination temperature on the microstructure and magnetic properties of Sr-ferrites
  18. Predicting the corrosion tendency of α-brass in acidic and alkaline tap water
  19. People
  20. 10.3139/146.610026
  21. DGM News
  22. DGM News
https://doi.org/10.3139/146.111143
Keywords for this article
Mg–Er alloy; Cold rolling; High strain rate; Rollability; Microstructure

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. A novel roll-bonding methodology for the cross-scale analysis of phase properties and interactions in multiphase structural materials
  5. Excellent cold rollability in a single pass of an Mg-4Er (wt.%) alloy
  6. An experimental study of the precipitation kinetics of pre-rolled Ni-Span-C 902 superalloy
  7. Influences of high temperature on the microstructural, electrical and mechanical properties of Ni-23 wt.% Al alloy
  8. Investigation of the wear resistance and microstructure of Al/SiC metal matrix composites as a function of reinforcement volume fraction and reinforcement to matrix particle size ratio applying artificial neural network
  9. Influence of zinc (II) ion concentration on Ni–Zn–P coatings deposited onto aluminum and their corrosion behavior
  10. Joining steel to aluminum alloy by resistance spot welding with a rivet
  11. Electrophysical and structure-sensitive properties of liquid Ga–In alloys
  12. Short Communications
  13. Synthesis and characterization of the novel nanocomposite Co(OH)2/graphene as supercapacitor materials
  14. Preparation of MnAlC flakes by surfactant-assisted ball-milling and the effects of annealing
  15. An improved two-stage sintering method for tungsten heavy alloys: conventional solid-phase sintering followed by microwave heating
  16. Effect of excess Pb on ferroelectric characteristics of conductive Al-doped ZnO and Sn-doped In2O3 top electrodes in PbLaZrTiOx capacitors
  17. Effects of La–Zn substituent and calcination temperature on the microstructure and magnetic properties of Sr-ferrites
  18. Predicting the corrosion tendency of α-brass in acidic and alkaline tap water
  19. People
  20. 10.3139/146.610026
  21. DGM News
  22. DGM News
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2025 De Gruyter Brill
Downloaded on 31.12.2025 from https://www.degruyterbrill.com/document/doi/10.3139/146.111143/pdf
Scroll to top button