Startseite Characterization of silicon-silicon carbide ceramic derived from carbon-carbon silicon carbide composites
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Characterization of silicon-silicon carbide ceramic derived from carbon-carbon silicon carbide composites

  • Vijay K. Srivastava und Walter Krenkel
Veröffentlicht/Copyright: 17. August 2013
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 104 Heft 4

Abstract

The main objective of the present work is to process porous silicon–silicon carbide (Si–SiC) ceramic by the oxidation of carbon–carbon silicon carbide (C/C–SiC) composites. Phase studies are performed on the oxidized porous composite to examine the changes due to the high temperature oxidation. Further, various characterization techniques are performed on Si–SiC ceramics in order to study the material's microstructure. The effects of various parameters such as fiber alignment (twill weave and short/chopped fiber) and phenolic resin type (resol and novolak) are characterized.

Keywords: Processing; Si–SiC ceramic; C/C–SiC composite; Carbon fiber; Oxidation
* Correspondence address, Prof. Vijay K. Srivastava, Department of Mechanical Engineering, Indian Institute of Technology, BHU, Varanasi-221005, India, Tel.: +91 542 6702833, Fax: +91 542 2368428, E-mail:

References

[1] W.Krenkel, in: Proc. Ceramic Engineering and Science Proceedings, American Ceramic Society, USA, vol. 22, 3 (2001) 443.Suche in Google Scholar

[2] F.J.Schulte, A.Zern, J.Mayer, M.Rühle, M.Frieß, W.Krenkel, R.Kochendörfer: Mater. Sci. Eng. A (2002) 146. 10.1016/S0921-5093(01)01719-1Suche in Google Scholar

[3] W.Krenkel, R.Renz, B.Heidenreich, in: Lightweight and wear resistant CMC brakes, Ceramic materials and components for engines (Eds.: J. G.Heinrich, F.Aldinger), WILEY-VCH, Weinheim, Germany, (2001) 63.Suche in Google Scholar

[4] W.Krenkel, in: Advances in Ceramic Matrix Composites IX, N.P.Bansal, J.P.Singh, W.K.Kriven, H.Schneider (Eds.), Ceram. Trans. vol.153 (2003) 103.Suche in Google Scholar

[5] W.Krenkel: Mol. Cryst. Liq. Cryst. Sci. 354, 1 (2000) 353.10.1080/10587250008023627Suche in Google Scholar

[6] L.P.Zawada, R.S.Hay, S.S.Lee, J.Staehler: J. Am. Ceram. Soc.86 (2003) 981. 10.1111/j.1151-2916.2003.tb03406.xSuche in Google Scholar

[7] C.G.Levi, J.Y.Yang, B.J.Dalgleish, F.W.Zok, A.G.Evans: J. Am. Ceram. Soc.81 (1998) 2077. 10.1111/j.1151-2916.1998.tb02590.xSuche in Google Scholar

[8] R.Weiss, in: Carbon fiber reinforced CMCs manufacture, properties, oxidation protection, high temperature ceramic matrix composites (Eds.: W.Krenkel, R.Naslain, H.Schneider), WILEY-VCH, Weinheim, Germany, (2001) 440.Suche in Google Scholar

[9] F.Christin: Adv. Eng. Mater.4 (2002) 903. 10.1002/adem.200290001Suche in Google Scholar

[10] R.Kochendörfer, N.Lützenburger, in: Application of CMCs made via the liquid silicon infiltration technique, high temperature ceramic matrix composites (Eds.: W.Krenkel, R.Naslain, H.Schneider), WILEY-VCH, Weinheim, Germany (2001) 277.Suche in Google Scholar

[11] V.K.Srivastava, W.Krenkel, V.J.A.D’Souza, H.W.Mucha: J. Ceram. Sci. Technol.2 (2011) 111.Suche in Google Scholar

Received: 2011-10-18
Accepted: 2012-8-20
Published Online: 2013-08-17
Published in Print: 2013-04-11

© 2013, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Original Contributions
  4. Modeling the effect of austenite deformation on the bainite structure parameters in low carbon microalloyed steels
  5. The precipitation of η phase in an Fe-Ni-based superalloy with different Ti/Al ratios
  6. Growth kinetics of aluminum-bearing intermetallic layer on tool steel
  7. Thermodynamic modeling of the Ba–Mg binary system
  8. Partial isothermal section of the Dy-Co-Ga ternary system at 500°C
  9. Solubility study of the copper-lead system
  10. Solidification of primary Si in electromagnetically levitated Al-50%Si undercooling melts
  11. Microstructure and mechanical properties of as-cast and solution-treated Mg-Zn-Gd-based alloys reinforced with quasicrystals
  12. Fabrication of micro/nano structured aluminum–nickel energetic composites by means of ultrasonic powder consolidation
  13. Study of an Al-Si-Cu HPDC alloy with high Zn content for the production of components requiring high ductility and tensile properties
  14. Characterization of silicon-silicon carbide ceramic derived from carbon-carbon silicon carbide composites
  15. Mechanochemical and combustion synthesis of CeB6
  16. Nanomechanical studies and materials characterization of metal/polymer bilayer MEMS cantilevers
  17. DGM News
  18. DGM News
https://doi.org/10.3139/146.110875
Schlagwörter für diesen Artikel
Processing; Si–SiC ceramic; C/C–SiC composite; Carbon fiber; Oxidation

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Original Contributions
  4. Modeling the effect of austenite deformation on the bainite structure parameters in low carbon microalloyed steels
  5. The precipitation of η phase in an Fe-Ni-based superalloy with different Ti/Al ratios
  6. Growth kinetics of aluminum-bearing intermetallic layer on tool steel
  7. Thermodynamic modeling of the Ba–Mg binary system
  8. Partial isothermal section of the Dy-Co-Ga ternary system at 500°C
  9. Solubility study of the copper-lead system
  10. Solidification of primary Si in electromagnetically levitated Al-50%Si undercooling melts
  11. Microstructure and mechanical properties of as-cast and solution-treated Mg-Zn-Gd-based alloys reinforced with quasicrystals
  12. Fabrication of micro/nano structured aluminum–nickel energetic composites by means of ultrasonic powder consolidation
  13. Study of an Al-Si-Cu HPDC alloy with high Zn content for the production of components requiring high ductility and tensile properties
  14. Characterization of silicon-silicon carbide ceramic derived from carbon-carbon silicon carbide composites
  15. Mechanochemical and combustion synthesis of CeB6
  16. Nanomechanical studies and materials characterization of metal/polymer bilayer MEMS cantilevers
  17. DGM News
  18. DGM News
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 2.10.2025 von https://www.degruyterbrill.com/document/doi/10.3139/146.110875/html
Button zum nach oben scrollen