Startseite Influence of interfaces on the mechanical properties of ultrahigh carbon steel multilayer laminates
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Influence of interfaces on the mechanical properties of ultrahigh carbon steel multilayer laminates

  • Marta Pozuelo , Fernando Carreño , Manuel Carsí und Oscar A. Ruano
Veröffentlicht/Copyright: 23. Mai 2013
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 98 Heft 1

Abstract

To improve impact and flexure properties of ultrahigh carbon steel (UHCS-1.3 wt.% C), a multilayer laminate consisting of 20 layers of the same UHCS has been processed by hot rolling. Two different rolling conditions gave rise to “soft” and “severe” laminates. The toughness of the “soft” laminate, measured by impact test absorbed energy, was more than forty times higher than that of the monolithic UHCS and three times higher than that of mild steels. In contrast, the “severe” laminate showed no increase in toughness with respect to the monolithic UHCS. This large difference in behaviour was studied by means of shear and bend tests, which gave valuable information on bond quality and delamination.

Keywords: Ultrahigh carbon steel laminates; Interfaces; Impact behaviour; Shear tests
* Correspondence address, Dr. Fernando Carreño, Departamento de Metalurgia Física, CENIM (CSIC), Av. Gregorio del Amo, 8, 28040 Madrid, Spain, Tel.: +34 91 553 8900, Fax: +34 91 534 7425, E-mail:

References

[1] A.Fernández-Vicente, M.Carsí, F.Peñalba, E.M.Taleff, O.A.Ruano, in: E.M.Taleff, C.K.Syn, O.D.Sherby (Eds.), Fracture behavior of two ultrahigh-carbon steels, TMS, Nashville, Tennessee (2000) 55.Suche in Google Scholar

[2] A.Fernández, J.Chao, M.Carsí, F.Peñalba, J.Ibáñez, in: M.Carsí, F.Peñalba, O.A.Ruano, B.J.Fernández (Eds.), VII Congreso Nacional de Tratamientos Térmicos y de Superficie. Barcelona, Spain (1998) 59.Suche in Google Scholar

[3] O.D.Sherby, T.Oyama, D.W.Kum, B.Walser, J.Wadsworth: J. Metals3 (1985) 50.Suche in Google Scholar

[4] M.Pozuelo, F.Carreño, O.A.Ruano, in: Proceedings of VIII Congreso Nacional de Propiedades Mecánicas de Sólidos. Gandia, Spain (2002) 943.Suche in Google Scholar

[5] D.W.Kum, T.Oyama, J.Wadsworth, O.D.Sherby: J. Mech. Phys. Solids31 (1983) 173.10.1016/0022-5096(83)90049-2Suche in Google Scholar

[6] S.Lee, J.Wadsworth, O.D.Sherby: Res. Mechanica31 (1990) 233.Suche in Google Scholar

[7] D.W.Kum, T.Oyama, O.A.Ruano, O.D.Sherby: Metall. Trans. A17 (1986) 1517.10.1007/BF02650087Suche in Google Scholar

[8] D.R.Lesuer, C.K.Syn, O.D.Sherby, J.Wadsworth, J.J.Lewandowski, W.H.Hunt: Int. Mater. Rev.41 (1996) 169.10.1179/095066096790151204Suche in Google Scholar

[9] F.Carreño, J.Chao, M.Pozuelo, O.A.Ruano: Scripta Mater.48 (2003) 1135.Suche in Google Scholar

[10] M.Pozuelo, F.Carreño, O.A.Ruano: Bol. Soc. Esp. Cerám. V.43 (2004) 207.Suche in Google Scholar

[11] R.A.Riddle, D.R.Lesuer, C.K.Syn: Recent Advances in Solids/Structures and Application of Metallic Materials342 (1996) 167.Suche in Google Scholar

[12] E.N.Drewry, R.J.Moon, K.J.Bowman, K.P.Trumble: Scripta Mater.41 (1999) 749.10.1016/S1359-6462(99)00212-2Suche in Google Scholar

[13] C.F.Feng, L.Froyen: Acta Mater.47 (1999) 4571.10.1016/S1359-6454(99)00326-2Suche in Google Scholar

[14] G.E.Dieter: Mechanical Metallurgy, McGraw-Hill Book Company, London (1988).Suche in Google Scholar

[15] D.R.Lesuer, C.K.Syn, R.Riddle, O.D.Sherby, in: J.J.Lewandowski, W.H.HuntJr (Eds.), Intrinsic and Extrinsic Fracture Mechanisms in Inorganic Composite Systems, The Minerals, Metals & Materials Society (1995) 93.Suche in Google Scholar

[16] D.R.Bloyer, K.T.Venkateswara Rao, R.O.Ritchie: Mater. Trans. A29 (1998) 2483.10.1007/s11661-998-0220-0Suche in Google Scholar

[17] M.Pozuelo, F.Carreño, O.A.Ruano: Mater. Sci. Forum426–432 (2003) 883.Suche in Google Scholar

[18] M.Pozuelo: Procesado y Caracterizacion Microestructural y Mecánica de Materiales Compuestos Laminados de Aceros de Elevadas Prestaciones, Ph.D. Thesis, Universidad Complutense de Madrid, Spain, 2004.Suche in Google Scholar

Received: 2005-11-3
Accepted: 2006-10-13
Published Online: 2013-05-23
Published in Print: 2007-01-01

© 2007, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Editorial
  4. Editorial
  5. Basic
  6. Synthesis and oxidation of Zr3Al3C5 powders
  7. Standard Gibbs energy of formation of Zn17Y2 and Zn12Y determined by solution calorimetry and measurement of heat capacity from near zero Kelvin
  8. Phase equilibria in the Zn–Fe–S system at 450°C
  9. Formation of δ-Al2O3 hollow nanoparticles via a chemical vapor condensation process
  10. Low-cycle fatigue and damage of an uncoated and coated single crystal nickel-base superalloy SCB
  11. Fluidity of Mg–Al–Ca alloys in the high-pressure die casting process
  12. Applied
  13. Mechanical properties of rope-reinforced aluminium extrusions under quasistatic loading conditions
  14. Influence of interfaces on the mechanical properties of ultrahigh carbon steel multilayer laminates
  15. Thermomechanical processing of AA6061 billets for semi-solid forming
  16. Infrared spectroscopy and X-ray diffraction data of In – Se compounds
  17. Synthesis and characterization of MgAlON–BN composites
  18. Neutron diffraction residual stress analysis of steel engineering components: a study of the elastic and plastic anisotropy
  19. Notifications
  20. DGM News
https://doi.org/10.3139/146.101431
Schlagwörter für diesen Artikel
Ultrahigh carbon steel laminates; Interfaces; Impact behaviour; Shear tests

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Editorial
  4. Editorial
  5. Basic
  6. Synthesis and oxidation of Zr3Al3C5 powders
  7. Standard Gibbs energy of formation of Zn17Y2 and Zn12Y determined by solution calorimetry and measurement of heat capacity from near zero Kelvin
  8. Phase equilibria in the Zn–Fe–S system at 450°C
  9. Formation of δ-Al2O3 hollow nanoparticles via a chemical vapor condensation process
  10. Low-cycle fatigue and damage of an uncoated and coated single crystal nickel-base superalloy SCB
  11. Fluidity of Mg–Al–Ca alloys in the high-pressure die casting process
  12. Applied
  13. Mechanical properties of rope-reinforced aluminium extrusions under quasistatic loading conditions
  14. Influence of interfaces on the mechanical properties of ultrahigh carbon steel multilayer laminates
  15. Thermomechanical processing of AA6061 billets for semi-solid forming
  16. Infrared spectroscopy and X-ray diffraction data of In – Se compounds
  17. Synthesis and characterization of MgAlON–BN composites
  18. Neutron diffraction residual stress analysis of steel engineering components: a study of the elastic and plastic anisotropy
  19. Notifications
  20. DGM News
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 16.11.2025 von https://www.degruyterbrill.com/document/doi/10.3139/146.101431/pdf
Button zum nach oben scrollen