Artikel
Lizenziert
Nicht lizenziert
Erfordert eine Authentifizierung
Optimization of flank wear and surface roughness during turning of AISI 304 stainless steel using the Taguchi method
-
Nursel Altan Özbek
,
Metin İbrahim Karadag
Veröffentlicht/Copyright:
13. Februar 2021
Abstract
This paper presents the effect of cutting tool, cutting speed and feed rate on the flank wear and surface roughness of austenitic stainless steel (AISI 304) during wet turning. Turning tests were designed based on the Taguchi method (L18). An orthogonal array, the signal-to-noise ratio (S/N) and the ANOVA were used to investigate the machinability of AISI 304 stainless steel with PVD and CVD coated tungsten carbide inserts. As a result of ANOVA, it was found that the feed rate was the most effective parameter on both flank wear and surface roughness.
Keywords: AISI 304 austenitic stainless steel; PVD/CVD coating; flank wear; surface roughness; optimization
Published Online: 2021-02-13
Published in Print: 2020-09-01
© 2020 by Walter de Gruyter Berlin/Boston
Sie haben derzeit keinen Zugang zu diesem Inhalt.
Sie haben derzeit keinen Zugang zu diesem Inhalt.
Artikel in diesem Heft
- Titelei
- CONTENTS
- Materials Testing
- FACHBEITRÄGE
- Early stage crack detection in mechanically joined steel/aluminum joints by condition monitoring
- Microstructure, mechanical and corrosion properties of TIG welded Hastelloy C-276
- Residual stress evaluation during RSW of DP600 sheet steel
- Capability of martensitic low transformation temperature welding consumables for increasing the fatigue strength of high strength steel joints
- Hydroforming analysis of exhaust pipe connectors
- TiC coatings on an alloyed steel produced by thermal diffusion
- Mechanical and dielectric behavior of LDPE/Bi-1212 films
- Effect of heat treatment on corrosion and ultrasonic cavitation erosion resistance of AlSi10MnMg alloy
- Effect of impact source on detection quality in impact echo testing of sleeve grouting
- Influence of fiber weight ratio on the mechanical and water absorption performance of borassus/epoxy composites
- Effect of loading rate on cohesive parameters of the adhesive Araldite 2015
- Fatigue behavior of unbonded prestressed reactive powder concrete beams after creep
- Optimization of flank wear and surface roughness during turning of AISI 304 stainless steel using the Taguchi method
- Characterization of hydrogen in a high strength aluminum alloy
- BEZUGSQUELLEN
- IMPRESSUM
Schlagwörter für diesen Artikel
AISI 304 austenitic stainless steel;
PVD/CVD coating;
flank wear;
surface roughness;
optimization
Artikel in diesem Heft
- Titelei
- CONTENTS
- Materials Testing
- FACHBEITRÄGE
- Early stage crack detection in mechanically joined steel/aluminum joints by condition monitoring
- Microstructure, mechanical and corrosion properties of TIG welded Hastelloy C-276
- Residual stress evaluation during RSW of DP600 sheet steel
- Capability of martensitic low transformation temperature welding consumables for increasing the fatigue strength of high strength steel joints
- Hydroforming analysis of exhaust pipe connectors
- TiC coatings on an alloyed steel produced by thermal diffusion
- Mechanical and dielectric behavior of LDPE/Bi-1212 films
- Effect of heat treatment on corrosion and ultrasonic cavitation erosion resistance of AlSi10MnMg alloy
- Effect of impact source on detection quality in impact echo testing of sleeve grouting
- Influence of fiber weight ratio on the mechanical and water absorption performance of borassus/epoxy composites
- Effect of loading rate on cohesive parameters of the adhesive Araldite 2015
- Fatigue behavior of unbonded prestressed reactive powder concrete beams after creep
- Optimization of flank wear and surface roughness during turning of AISI 304 stainless steel using the Taguchi method
- Characterization of hydrogen in a high strength aluminum alloy
- BEZUGSQUELLEN
- IMPRESSUM
