Startseite Strength and mechanical response of C/C composite open-hole and bolted plates
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Strength and mechanical response of C/C composite open-hole and bolted plates

  • Zhiyong Tan , Weili Dong , Jie Mei , Jialin Liu , Jiayi Liu und Yuling Tang
Veröffentlicht/Copyright: 28. August 2017
Veröffentlichen auch Sie bei De Gruyter Brill
Manuskript einreichen Informationen für Autor*innen
Materials Testing
Aus der Zeitschrift Materials Testing Band 59 Heft 9

Abstract

The strength and mechanical responses of C/C composite open-hole and bolted plates were investigated in this paper. The tensile strength of C/C composite open-hole plates was experimentally tested and predicted by the point stress criterion. The effect of hole diameter on tensile strength of C/C composite open-hole plates was studied. The comparison of the predicted and experimental data indicated that the measured tensile strength was in reasonable agreement with the predictions. The bearing characteristic of C/C composite bolted plates was tested, and the effect of ply sequences, bolt diameter and torque on bearing properties was analyzed. The damage mechanism of C/C composite bolted plates was revealed.

Kurzfassung

In der diesem Beitrag zugrunde liegenden Studie wurden die Festigkeit und das mechanische Verhalten von gelochten und genieteten C/C-Kompositplatten untersucht. Die Zugfestigkeit der gelochten C/C-Kompositplatten wurde experimentell geprüft und mittels des Punktspannungskirteriums vorhergesagt. Die Auswirkung des Lochdurchmessers auf die Festigkeit der gelochten C/C-Kompositplatten wurde bestimmt. Der Vergleich zwischen den vorhergesagten und experimentell ermittelten Daten deutet darauf hin, dass die gemessene Zugfestigkeit in guter Übereinstimmung mit den Vorhersagen steht. Es wurde auch die Lagercharakteristik der genieteten C/C-Kompositplatten geprüft und die Auswirkungen der Lagenfolge, des Nietdurchmessers und der Torsion auf die Lagereigenschaften analysiert. Daraus wurde der Schädigungsmechanismus der genieteten C/C-Kompositplatten abgeleitet.

*Correspondence Address, Dr. Jiayi Liu, School of Naval Architecture and Ocean Engineering, Huazhong University of Science and Technology, Wuhan 430074, PR China. E-mail:

Prof. Zhiyong Tan, born in 1965, works as Professor in the Science and Technology on Space Physics Laboratory, Beijing Institute of Nearspace Vehicle's Systems Engineering, Beijing, P. R. China. He received his PhD degree in 1997 from Zhejiang University, Zhejiang, P. R. China. His research interest focuses on the advanced composite materials.

Dr. Weili Dong, born in 1986, works as an engineer in the Science and Technology on Space Physics Laboratory, Beijing Institute of Nearspace Vehicle's Systems Engineering, Beijing, P. R. China. He received his PhD degree in 2015 from Beijing Institute of Technology, Beijing, P. R. China. His research interest focuses on the advanced composite materials.

Jie Mei, born in 1994, is a master student of Design and Construction of Naval Architecture and Ocean Structure at the School of Naval Architecture and Ocean Engineering, Huazhong University of Science and Technology, Wuhan, P. R. China. He received his Bachelor degree in 2016 from Hohai University, Nanjing, P. R. China. His research interest focuses on the composite lightweight structure.

Jialin Liu, born in 1992, is a master student of Design and Construction of Naval Architecture and Ocean Structure at the School of Naval Architecture and Ocean Engineering, Huazhong University of Science and Technology, Wuhan, P. R. China. He received his Bachelor degree in 2016 from Huazhong University of Science and Technology, Wuhan, P. R. China. His research interest focuses on the composite lightweight structure.

Dr. Jiayi Liu, born in 1985, works as a lecturer at the School of Naval Architecture and Ocean Engineering, Huazhong University of Science and Technology, Wuhan, P. R. China. He received his PhD degree in 2013 from Harbin Institute of Technology, Harbin, P. R. China. His research interest focuses on the composite lightweight structure.

Dr. Yuling Tang, born in 1981, works as a lecturer at College of Mechanical Engineering, Tianjin University of Science and Technology, Tianjin, P. R. China. He received his PhD degree in 2015 from Harbin Institute of Technology, Harbin, P. R. China. His research interest focuses on the advanced composite materials.

References

1 M. J.Xie: Connection of Composite Materials, Shanghai Jiaotong University Press, China (2011)Suche in Google Scholar

2 A.Todoroki, K.Ohara, Y.Mizutani, Y.Suzuki, R.Matsuzaki: Self-sensing time-domain reflectometry for detection of the bearing failure of a CFRP laminate fastener hole: Effect of peeling of the insulator, Advanced Composite Materials25 (2016), pp. 457–46910.1080/09243046.2015.1087176Suche in Google Scholar

3 L.Liu, J.Zhang, K.Chen, H.Wang: Influences of assembly parameters on the strength of bolted composite-metal joints under tensile loading, Advanced Composite Materials22 (2013), pp. 339–35910.1080/09243046.2013.824855Suche in Google Scholar

4 W. Y.Liang, Z. W.Duan, Z. Q.Wang, P. C.Lin: Experimental and numerical investigation on bolted joint in glass-fiber reinforced composites, Advanced Composite Materials24 (2015), pp. 161–17310.1080/09243046.2014.976733Suche in Google Scholar

5 M.Pakdil, F.Sen, O.Sayman, S.Benli: Bearing failure in bolted composite joints: Analytical tools development, Journal of Reinforced Plastics and Composites26 (2007), pp. 1239–125110.1177/0731684407079769Suche in Google Scholar

6 Y.Fukada: Bearing strength of carbon fiber/epoxy laminate with direct measurement of hole deformation, Advanced Composite Materials22 (2013), pp. 311–32510.1080/09243046.2013.814752Suche in Google Scholar

7 K. C.Warren, R. A.Lopez-Anido, S. S.Vel, H. H.Bayraktar: Progressive failure analysis of three-dimensional woven carbon composites in single-bolt, double-shear bearing, Composites Part B84 (2016), pp. 266–27610.1016/j.compositesb.2015.08.082Suche in Google Scholar

8 G.Kelly, L.Hallström: Bearing strength of carbon fiber/epoxy laminates: effects of bolt-hole clearance, Composites Part B35 (2004), pp. 331–34310.1016/j.compositesb.2003.11.001Suche in Google Scholar

9 Y. N.Zhai, D. S.Li, X. Q.Li, L.Wang: An experimental study on the effect of joining interface condition on bearing response of single-lap, countersunk composite-aluminum bolted joints, Composite Structures134 (2015), pp. 190–19810.1016/j.compstruct.2015.08.078Suche in Google Scholar

10 J.Lecomte, C.Bois, H.Wargnier, J. C.Wahl: An analytical model for the prediction of load distribution in multi-bolt composite joints including hole-location errors, Composite Structures117 (2014), pp. 354–36110.1016/j.compstruct.2014.06.040Suche in Google Scholar

11 Z. Y.Wang, N.Zhang, Q. Y.Wang: Tensile behavior of open-hole and bolted steel plates reinforced by CFRP strips, Composites Part B100 (2016), pp. 101–11310.1016/j.compositesb.2016.06.038Suche in Google Scholar

12 J.Ekh, J.Schön, D.Zenkert: Simple and efficient prediction of bearing failure in single shear, composite lap joints, Composite Structures105 (2013), pp. 35–4410.1016/j.compstruct.2013.04.038Suche in Google Scholar

13 L. B.Zhao, A.Xin, F. R.Liu, J. Y.Zhang, N.Hu: Secondary bending effects in progressively damaged single-lap, single-bolt composite joints, Results in Physics6 (2016), pp. 704–71110.1016/j.rinp.2016.08.021Suche in Google Scholar

14 Y.Kogo, H.Hatta, H.Kawada, T.Machida: Effect of stress concentration on tensile fracture behavior of carbon-carbon composites, Journal of Composite Materials32 (1998), pp. 1273–129410.1177/002199839803201302Suche in Google Scholar

15 K. S.Ahmed, S.Vijayarangan, A. C. B.Naidu: Elastic properties, notched strength and fracture criterion in untreated woven jute-glass fabric reinforced polyester hybrid composites, Materials & Design28 (2007), pp. 2287–229410.1016/j.matdes.2006.08.002Suche in Google Scholar

Published Online: 2017-08-28
Published in Print: 2017-09-01

© 2017, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Inhalt/Contents
  2. Contents
  3. Fachbeiträge/Technical Contributions
  4. Effect of contact pressure on multiaxial fretting fatigue behavior of Al-Zn-Mg alloy
  5. Effect of various initial concentrations of CTAB on the noncovalent modified graphene oxide (MGNO) structure and thermal stability
  6. Bauschinger effect at elevated temperatures in a 2024-T3 aluminum alloy for designing wind turbine components
  7. Effect of Ni interlayer on diffusion bonding of a W alloy and a Ta alloy
  8. Comparison of the welding behavior of P/M borated and I/M borated stainless steel
  9. Detection of interfacial debonding in epoxy resin-bonded lead-steel structure using laser ultrasonics
  10. Effects of deep cryo treatment of high speed steel on the turning process of a medium carbon steel
  11. Weldability of superalloys alloy 718 and ATI® 718Plus™ – A study performed by Varestraint testing
  12. Strength and mechanical response of C/C composite open-hole and bolted plates
  13. Pullout performance of modified threads in glass fiber reinforced plastic (GFRP) composites
  14. Physico-chemical characterization of slag waste from coal gasification syngas plants: Effect of the gasification temperature on slag waste as construction material
  15. Preparation, characterization and thermoelectric properties of a polyaniline matrix Ge0.94Pb0.01Bi0.05Te composite
  16. Surface roughness analysis of greater cutting depths during hard turning
  17. Properties of fine soils contaminated with gas oil
  18. Numerical calculation and stress analysis of crack evolution in coal with a central hole under nonuniform load
https://doi.org/10.3139/120.111067

Artikel in diesem Heft

  1. Inhalt/Contents
  2. Contents
  3. Fachbeiträge/Technical Contributions
  4. Effect of contact pressure on multiaxial fretting fatigue behavior of Al-Zn-Mg alloy
  5. Effect of various initial concentrations of CTAB on the noncovalent modified graphene oxide (MGNO) structure and thermal stability
  6. Bauschinger effect at elevated temperatures in a 2024-T3 aluminum alloy for designing wind turbine components
  7. Effect of Ni interlayer on diffusion bonding of a W alloy and a Ta alloy
  8. Comparison of the welding behavior of P/M borated and I/M borated stainless steel
  9. Detection of interfacial debonding in epoxy resin-bonded lead-steel structure using laser ultrasonics
  10. Effects of deep cryo treatment of high speed steel on the turning process of a medium carbon steel
  11. Weldability of superalloys alloy 718 and ATI® 718Plus™ – A study performed by Varestraint testing
  12. Strength and mechanical response of C/C composite open-hole and bolted plates
  13. Pullout performance of modified threads in glass fiber reinforced plastic (GFRP) composites
  14. Physico-chemical characterization of slag waste from coal gasification syngas plants: Effect of the gasification temperature on slag waste as construction material
  15. Preparation, characterization and thermoelectric properties of a polyaniline matrix Ge0.94Pb0.01Bi0.05Te composite
  16. Surface roughness analysis of greater cutting depths during hard turning
  17. Properties of fine soils contaminated with gas oil
  18. Numerical calculation and stress analysis of crack evolution in coal with a central hole under nonuniform load
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 25.10.2025 von https://www.degruyterbrill.com/document/doi/10.3139/120.111067/pdf?lang=de
Button zum nach oben scrollen