The memory effect in polyolefinic products: A tool for confirming the steam sterilization process
-
Kamila Bajer
Abstract
The goal of this investigation is to understand a distinctive feature observed in differential scanning calorimetry (DSC) measurements of steam sterilized medical polymer products, the formation of a peak upon the first DSC heating, known as the “memory effect”. The observed phenomenon could be used to provide evidence for steam sterilization. For the investigations, polypropylene (PP) and polyethylene (PE) samples were steam sterilized or thermally treated in an oven applying different conditions. Afterwards, the samples were measured by DSC. The influences of thermal treatment and mechanical stress were analyzed. In addition, various polyolefin reference materials (PE and PP) were investigated to address the influence of composition. Furthermore, the durability of the signal with respect to time and temperature effects were examined. The investigation shows that it is possible to produce a stable memory effect.
Kurzfassung
DSC-Messungen von dampfsterilisierten medizinischen Produkten aus Polyolefinen zeigen beim ersten Heizvorgang als auffällige Besonderheit eine zusätzliche Stufe, bekannt als Temperpeak. Das Ziel dieser Untersuchungen ist, dieses Phänomen nachzuvollziehen und zu verstehen, um es als Nachweis für die Dampfsterilisation nutzen zu können. Dafür wurden PP- und PE-Proben unter verschiedenen Bedingungen dampfsterilisiert und im Ofen thermisch behandelt. Anschließend wurden die Proben mittels DSC untersucht und die Einflüsse der thermischen Behandlung und der mechanischen Beanspruchung analysiert. Um den Einfluss unterschiedlicher Materialspezifikationen zu prüfen, wurden zusätzlich verschiedene Referenzmaterialien (PE und PP) untersucht und GPC-Messungen durchgeführt. Des Weiteren wurde die Beständigkeit des Signals gegenüber der Zeit und der Temperatureinflüssen betrachtet. Die Untersuchungen zeigen, dass sich ein stabiler Memory-Effekt erzeugen lässt.
References
1 A. T.Jones, J. M.Aizlewood, D. R.Beckett: Crystalline forms of isotactic polypropylene, Makromolekulare Chemie75 (1964), pp. 134–15810.1016/0032-3861(96)00370-9Search in Google Scholar
2 B.Lotz, J. C.Wittmann, A. J.Lovinger: Structure and morphology of polypropylenes: A molecular analysis, Polymer37 (1996), pp. 4979–499210.1016/0032-3861(96)00370-9Search in Google Scholar
3 E. A.Turi: Thermal characterization of polymeric materials, Academic Press, New York (1981)Search in Google Scholar
4 M.Schiller, R. D.Maier, M.Schiller: Plastics Additives Handbook, 6th Ed., Carl Hanser Verlag, München (2009)Search in Google Scholar
5 J.Varga: Beta-modification of isotactic polypropylene: Preparation, structure, processing, properties, and application, Journal of Macromolecular Science – Part B – Physics, 41 (2002), pp. 1121–117110.1081/mb-120013089Search in Google Scholar
6 J.Varga: Beta-modification of polypropylene and its 2-component systems, Journal of Thermal Analysis35 (1989), pp. 1891–191210.1007/bf01911675Search in Google Scholar
7 S. C.Wang, J.Zhang, S. J.Chen, H.Zhu: Crystal structure and melting behavior of homo-polypropylene and heterophasic ethylene-propylene copolymer after long-time heat treatment, Journal of Crystal Growth355 (2012), pp. 151–15810.1016/j.jcrysgro.2012.06.030Search in Google Scholar
8 J.Kang, J. Y.Chen, Y.Cao, H. L.Li: Effects of ultrasound on the conformation and crystallization behavior of isotactic polypropylene and beta-isotactic polypropylene, Polymer51 (2010), pp. 249–25610.1016/j.polymer.2009.11.018Search in Google Scholar
9 G. W.Ehrenstein, G.Riedel, P.Trawiel: Thermal Analysis of Plastics, Theory and Practice, Carl Hanser Verlag, München (2004)10.3139/9783446434141.fmSearch in Google Scholar
10 S.Castagnet, L.Thilly: High-pressure dependence of structural evolution in polyamide 11 during annealing, Journal of Polymer Science Part B – Polymer Physics, 47 (2009), pp. 2015–202510.1002/polb.21800Search in Google Scholar
11 N.Alberola, M.Fugier, D.Petit, B.Fillon: Microstructure of quenched and annealed films of isotactic polypropylene, Journal of Materials Science30 (1995), pp. 1187–119510.1007/bf00356118Search in Google Scholar
12 W.Müller, Th.Pretsch: Hydrolytic aging of crystallizable shape memory poly(ester urethane): Effects on the thermo-mechanical properties and visco-elastic modeling, European Polymer Journal46 (2010), pp. 1745–175810.1016/j.eurpolymj.2010.05.004Search in Google Scholar
13 Th.Pretsch: Durability of a polymer with triple-shape properties, Polymer Degradation and Stability95 (2010), pp. 2515–252410.1016/j.polymdegradstab.2010.07.037Search in Google Scholar
14 A.Lendlein, St.Kelch: Shape-memory polymers: Angewandte Chemie International Edition41 (2002), pp. 2034–205710.1002/1521-3773(20020617)41:12<2034::aid-anie2034>3.0.co;2-mSearch in Google Scholar
15 EN 285:2006+a2:2009, Sterilization – steam sterilizers – large sterilizers, 2009Search in Google Scholar
16 EN 13060:2004+a2:2010; small steam sterilizers, 2010Search in Google Scholar
17 B.Galabov, S.Ilieva: Predicted infrared spectrum of polyethylene: Journal of Molecular Liquids53 (1992), pp. 55–6410.1016/0167-7322(92)80047-LSearch in Google Scholar
18 R. G.Brown: Infrared spectra of polyethylene crystals, Journal of Applied Physics34 (1963), pp. 2382–238710.1063/1.1702751Search in Google Scholar
19 ISO 11357-1, plastics – differential scanning calorimetry (DSC) – part 1: General principles, (2010)Search in Google Scholar
20 K.Kalaitzidou, H.Fukushima, P.Askeland, L. T.Drzal: The nucleating effect of exfoliated graphite nanoplatelets and their influence on the crystal structure and electrical conductivity of polypropylene nanocomposites, Journal of Materials Science43 (2008), pp. 2895–290710.1007/s10853-007-1876-3Search in Google Scholar
21 A. R.Bhattacharyya, T. V.Sreekumar, T.Liu, S.Kumar, L. M.Ericson, R. H.Hauge, R. E.Smalley: Crystallization and orientation studies in polypropylene/single wall carbon nanotube composite, Polymer44 (2003), pp. 2373–237710.1016/s0032-3861(03)00073-9Search in Google Scholar
22 B.Monasse, J. M.Haudin: Effect of random copolymerization on growth transition and morphology change in polypropylene, Colloid and Polymer Science266 (1988), pp. 679–68710.1007/bf01410276Search in Google Scholar
23 K. D.Pae, J. A.Sauer: Effects of thermal history on isotactic polypropylene, Journal of Applied Polymer Science12 (1968), p. 190110.1002/app.1968.070120811Search in Google Scholar
© 2015, Carl Hanser Verlag, München
Articles in the same Issue
- Inhalt/Contents
- Inhalt
- Fachbeiträge/Technical Contributions
- Influence of the production process on the deformation and fatigue performance of friction drilled internal threads in the aluminum alloy 6060*
- Effect of quench and strain aging on the mechanical properties of low carbon microalloyed steels
- Effect of temperature on microstructure and mechanical behavior of diffusion bonded Armor 500 and AISI 1040 steels
- Analysis of industrial conditions during multi-stage cooling of C70D high-carbon steel wire rod
- Effect of cryogenic treatment on the microstructure and wear behavior of a T-42 tool steel
- Application of the response surface methodology in the ball burnishing process for the prediction and analysis of surface hardness of the aluminum alloy AA 7075
- The memory effect in polyolefinic products: A tool for confirming the steam sterilization process
- Neutron tomography in archaeology*
- Ultraschallprüfung von Betonbauteilen – laufzeitgesteuerte Gruppenstrahler mit Punktkontaktprüfköpfen
- Acoustic emission testing of surface roughness and wear caused by grinding of ceramic materials
- Electrochemical impedance spectroscopy of hardened compacted cemented soils at early curing stage
- Microstructure and pore fractal dimensions of recycled thermal insulation concrete
- Microstructure and tribological properties of electrolytic plasma nitrided high-speed steel
- Exploitation of limestone in brick making
- Effect of alkaline treatment on physico-mechanical properties of black rice husk ash filled polypropylene biocomposites
- Kalender/Calendar
- Kalender
Articles in the same Issue
- Inhalt/Contents
- Inhalt
- Fachbeiträge/Technical Contributions
- Influence of the production process on the deformation and fatigue performance of friction drilled internal threads in the aluminum alloy 6060*
- Effect of quench and strain aging on the mechanical properties of low carbon microalloyed steels
- Effect of temperature on microstructure and mechanical behavior of diffusion bonded Armor 500 and AISI 1040 steels
- Analysis of industrial conditions during multi-stage cooling of C70D high-carbon steel wire rod
- Effect of cryogenic treatment on the microstructure and wear behavior of a T-42 tool steel
- Application of the response surface methodology in the ball burnishing process for the prediction and analysis of surface hardness of the aluminum alloy AA 7075
- The memory effect in polyolefinic products: A tool for confirming the steam sterilization process
- Neutron tomography in archaeology*
- Ultraschallprüfung von Betonbauteilen – laufzeitgesteuerte Gruppenstrahler mit Punktkontaktprüfköpfen
- Acoustic emission testing of surface roughness and wear caused by grinding of ceramic materials
- Electrochemical impedance spectroscopy of hardened compacted cemented soils at early curing stage
- Microstructure and pore fractal dimensions of recycled thermal insulation concrete
- Microstructure and tribological properties of electrolytic plasma nitrided high-speed steel
- Exploitation of limestone in brick making
- Effect of alkaline treatment on physico-mechanical properties of black rice husk ash filled polypropylene biocomposites
- Kalender/Calendar
- Kalender
