Wear Behavior of Fe-C-Cr Based Hardfacing Alloys Dependent on Ferrovanadium and Ferrotungsten Addition*

Gülin Kapali; Salim Şahin; Nilay Yüksel; Fatih Sargin; Barbaros Yaman

doi:10.3139/120.110644

Artikel

Wear Behavior of Fe-C-Cr Based Hardfacing Alloys Dependent on Ferrovanadium and Ferrotungsten Addition*

Gülin Kapali , Salim Şahin , Nilay Yüksel , Fatih Sargin und Barbaros Yaman

Veröffentlicht/Copyright: 11. Oktober 2014

Veröffentlicht von

Veröffentlichen auch Sie bei De Gruyter Brill

Manuskript einreichen Informationen für Autor*innen

Aus der Zeitschrift Materials Testing Band 56 Heft 10

Abstract

The aim of this study is to investigate the effect of vanadium and tungsten on wear behavior of Fe-C-Cr based hardfacing alloys. The wear behavior of hardfacing layers was determined by dry sand/rubber wheel abrasion tests according to ASTM G-65. The results of the abrasion tests were interpreted by metallographic examinations, SEM and EDX analyses as well as hardness measurements. According to the results of the experimental studies, the effect of W and V addition was discussed.

Kurzfassung

Das Ziel der diesem Beitrag zugrunde liegenden Studie bestand darin, die Auswirkungen von Vanadium und Wolfram auf das Verschleißverhalten von Fe-C-Cr basierten Aufschweißlegierungen zu untersuchen. Das Verschleißverhalten der Aufschweißungen wurde mittels des trockenen Sand-Gummirad Abrasionsversuches entsprechend ASTM G-65 ermittelt. Die Ergebnisse des Abrasionsversuches wurden mittels metallografischer Untersuchungen, REM- und EDX-Analysen sowie Härtemessungen ausgewertet. Anhand der experimentellen Untersuchungsergebnisse wird die Wirkung von Vanadium- und Wolframzugabe diskutiert.

**Correspondence Address Associate Prof. Dr. Salim Şahin, MSc Nilay Yüksel, Celal Bayar University, Engineering Faculty, Department of Materials Engineering, 45140 Muradiye, Manisa, Turkey, E-mail: nilay.yuksel@cbu.edu.tr

Gülin Kapali, born in 1989, graduated in 2011 from Celal Bayar University in Manisa, Turkey, with a degree in Mechanical Engineer. Currently, she is working on her Master degree in Mechanical Engineering at Celal Bayar University.

Salim Şahin, born in 1969, graduated in 1991 from Dokuz Eylül University with a degree in Mechanical Engineering. In 1995, he completed his Master of Science in Mechanical Engineering at Celal Bayar University in Manisa, Turkey, and in 2000, he completed his PhD at that same university. In 2010, he was appointed Associate Professor and has been working since then in that position in the Department of Materials Engineering at Celal Bayar University.

Nilay Yüksel, born in 1988, graduated in 2010 from Celal Bayar University in Manisa, Turkey, with a degree in Mechanical Engineering. She completed her Master of Science in the Department of Mechanical Engineering at the same university in 2012. Within the same year, she started her PhD study at Celal Bayar University.

Fatih Sargin, born in 1988, graduated in 2011 from Sakarya University, Turkey, with a degree in Metallurgy and Materials Engineering. He started working on his Master of Science in the Department of Materials Engineering at the same university in 2013.

Barbaros Yaman, born in 1976, completed the undergraduate program in 2000 in the Department of Mechanical Engineering at Dumlupınar University, Turkey. He is the owner of the Yaman Kaynak Company in Izmir, Turkey.

Presented during the 3^rd International Conference on Welding Technologies and Exhibition (ICWET'14) in Manisa, Turkey

References

1 M.Petrica, C.Katsich, E.Badisch, F.Kremsner: Study of abrasive wear phenomena in dry and slurry 3-body conditions, Tribology International64 (2013), pp. 196–20310.1016/j.triboint.2013.03.028Suche in Google Scholar

2 P. F.Mendez, N.Barnes, K.Bell, S. D.Borle, S. S.Gajapathi, S. D.Guest, H.Izadi, A. K.Gol, G.Wood: Welding processes for wear resistant overlays, Journal of Manufacturing Processes16 (2014), pp. 4–2510.1016/j.jmapro.2013.06.011Suche in Google Scholar

3 A.Zikin, E.Badisch, I.Hussainova, C.Tomastik, H.Danninger: Characterisation of TiC-NiMo reinforced Ni-based hardfacing, Surface & Coatings Technology236 (2013), pp. 36–4410.1016/j.surfcoat.2013.02.027Suche in Google Scholar

4 J.Hornung, A.Zikin, K.Pichelbauer, M.Kalin, M.Kirchgaßner: Infiuence of cooling speed on the microstructure and wear behaviour of hypereutectic Fe-Cr-C hardfacings, Materials Science and Engineering A576 (2013), pp. 243–25110.1016/j.msea.2013.04.029Suche in Google Scholar

5 K.Yang, Q.Yang, Y.Bao: Effect of carbonitride precipitates on the solid/liquid erosion behaviour of hardfacing alloy, Applied Surface Science284 (2013), pp. 540–54410.1016/j.apsusc.2013.07.130Suche in Google Scholar

6 R.Veinthal, F.Sergejev, A.Zikin, R.Tarbe, J.Hornung: Abrasive impact wear and surface fatigue wear behaviour of Fe-Cr-C PTA overlays, Wear301 (2013), pp. 102–10810.1016/j.msea.2013.04.029Suche in Google Scholar

7 X.Wang, F.Han, X.Liu, S.Qu, Z.Zou: Microstructure and wear properties of the Fe-Ti-V-Mo-C hardfacing alloy, Wear265 (2008), pp. 583–58910.1016/j.wear.2007.12.001Suche in Google Scholar

8 P. W.Leech, X. S.Li, N.Alam: Comparison of abrasive wear of a complex high alloy hardfacing deposit and WC-Ni based metal matrix composite, Wear294–295 (2012), pp. 380–38610.1016/j.wear.2012.07.015Suche in Google Scholar

9 D.Liu, R.Liu, Y.Wei, Y.Ma, K.Zhu: Microstructure and wear properties of Fe-15Cr-2.5Ti-2C-xB wt.-% hardfacing alloys, Applied Surface Science271 (2013), pp. 253–25910.1016/j.apsusc.2013.01.169Suche in Google Scholar

10 Q.Wu, W.Li, N.Zhong, W.Gang, W.Haishan: Microstructure and wear behavior of laser cladding VC-Cr₇C₃ ceramic coating on steel substrate, Materials and Design49 (2013), pp. 10–1810.1016/j.matdes.2013.01.067Suche in Google Scholar

11 Q.Ming, L. C.Lim, Z. D.Chen: Laser cladding of nickel-based hardfacing alloys, Surface and Coatings Technology106 (1998), pp. 174–18210.1016/S0257-8972(98)00524-6Suche in Google Scholar

12 J. M.Amado, M. J.Tobar, J. C.Alvarez, J.Lamas, A.Yáñez: Laser cladding of tungsten carbides (Spherotene^®) hardfacing alloys for the mining and mineral industry, Applied Surface Science255 (2009), pp. 5553–555610.1016/j.apsusc.2008.07.198Suche in Google Scholar

13 M.Mohammadnezhad, V.Javaheri, M.Shamanian, M.Naseri, M.Bahrami: Effects of vanadium addition on microstructure, mechanical properties and wear resistance of Ni-Hard4 white cast iron, Materials and Design49 (2013), pp. 888–89310.1016/j.matdes.2013.02.043Suche in Google Scholar

14 X.Qi, Z.Jia, Q.Yang, Y.Yang: Effects of vanadium additive on structure property and tribological performance of high chromium cast iron hardfacing metal, Surface & Coatings Technology205 (2011), pp. 5510–551410.1016/j.surfcoat.2011.06.027Suche in Google Scholar

15 B.Nedeljković, V.Lazić, S.Aleksandrović, B.Krstić, M.Mutavdžić, D.Milosavljević, M.Đorđević: Influence of the carbide type on tribological properties of the hard faced layers, MJoM16 (2010), pp. 77–90Suche in Google Scholar

16 E. O.Correa, N. G.Alcantara, D. G.Tecco, R. V.Kumar: Development of an iron-based hardfacing material reinforced with Fe-(TiW)C composite powder, Metallurgical and Materials Transactions A38A (2007), pp. 937–94510.1007/s11661-007-9141-6Suche in Google Scholar

17 X. H.Wang, Z. D.Zou, S. Y.Qu: Microstructure of Fe-Based Alloy Hardfacing Reinforced by TiC-VC Particles, Journal of Iron And Steel Research International13 (2006), pp. 51–5510.1016/S1006-706X(06)60078-2Suche in Google Scholar

Published Online: 2014-10-11

Published in Print: 2014-10-01

Sie haben derzeit keinen Zugang zu diesem Inhalt.

Artikel in diesem Heft

https://doi.org/10.3139/120.110644