Home Keramische Werkstoffe für Walzen und andere Komponenten für das Warmwalzen
Article
Licensed
Unlicensed Requires Authentication

Keramische Werkstoffe für Walzen und andere Komponenten für das Warmwalzen

  • Vyacheslav Goryany , Dirk Lowke Düsseldorf and Rolf Wagner
Published/Copyright: May 26, 2013
Become an author with De Gruyter Brill

Kurzfassung

Das Verhalten von Stauchbahnen aus verschleißfesten und hochtemperaturbeständigen keramischen Werkstoffen wie Siliciumnitrid (Si3N4) verschiedener Qualitäten sowie aluminiumoxydverstärktem Zirkonoxyd (ATZ) bei den Zylinderstauchversuchen mit Stahl, Kupfer-Zinn- (CuSn), Kupfer-Silber-Legierungen (CuAg) wurde untersucht. Die dargestellten Ergebnisse zeigen die Oberflächensituation der Stauchbahnen (Porigkeit, Rissbildung, Anhaftungen, Verschleiß) vor und nach den Kalt- und Warmumformversuchen. Der Oberflächenzustand der Proben wurde mittels Licht- sowie Rasterelektronenmikroskopie analysiert.

Abstract

Aim of the investigation was the examination of the behaviour of crushing tracks on wear and high temperature resistant ceramic materials like different silicon nitride qualities (Si3N4), Alumina Toughened Zirconia (ATZ) by using zylinder upset test with steel, copper tin (CuSn) and copper silver alloys (CuAg). The results shows the situation of crushing tracks (porosity, cracks, adhesion, wear) before and after cold and hot deformation tests. The surface conditions of the samples were analyzed by light (LM) and scanning electron microscopy (SEM).


Dr. Vyacheslav Goryany, geboren 1956, studierte von 1973 bis 1978 am Institut für Metallurgie in Dnepropetrovsk. Danach war er als wissenschaftlicher Mitarbeiter an diesem Institut tätig. Im Jahr 1987 promovierte er am Institut für Maschinenbau sowie 1991 an der Universität Sarajevo. 1993 habilitierte er sich. Zur Zeit der Untersuchung war als er wissenschaftlicher Mitarbeiter am Institut für Metallurgie und Umformtechnik der Universität Duisburg-Essen tätig.

Dr. Rolf Wagner, geboren 1960, studierte von 1979 bis 1985 Mineralogie am Institut für Kristallographie der Universität Köln. Von 1985 bis 1989 führte er seine Promotionsarbeit an der DLR in Köln-Porz durch, die durch die Promotion 1989 abgeschlossen wurde. Von 1989 bis 2001 arbeitete er als Leiter des Technikums bei FCT und ist seit 2001 in leitender Funktion bei H. C. Starck Ceramics in Selb tätig. Seit 2011 Forschung und Entwicklung der Karl Buch Walzengießerei GmbH & Co. KG in Siegen.


Literatur

1 V.Goryany, P. J.Mauk, C.Eckardt: Untersuchung keramischer Werkstoffe für Walzen und anderen Komponenten in der Walztechnik, Materials Testing52 (2010), No. 1-2, S. 100106Search in Google Scholar

2 V.Goryany, P. J.Mauk, J.Giersbach: Arbeitswalzen aus Keramik zum Walzen von dünnen Stahlfolien im 20-Walzen-Sendzimirgerüst, Materials Testing53 (2011), No. 10, S. 643648Search in Google Scholar

3 Y.Enomoto, K.Mizuhara: Characterisation of wear behaviour of steel and ceramics in the VAMAS round robin testsWear162-164 (1993), Part 1, S. 11912510.1016/0043-1648(93)90492-5Search in Google Scholar

4 M. G.Gee, D.Butterfield: The combined effect of speed and humidity on the wear and friction of silicon nitride, Wear162-164 (1993), Part 1, S. 23424510.1016/0043-1648(93)90506-HSearch in Google Scholar

5 L.Fang, Y.Gao, L.Zhou, P.Li: Unlubricated sliding wear ceramics against graphitized cast irons, Wear171 (1994), No. 1-2, S. 12913410.1016/0043-1648(94)90355-7Search in Google Scholar

6 A.Zutshi, R. A.Haber, D. E.Niesz, J. W.Adams, J. B.Wachtman, M. K.Ferber, S. M.Hsu: Processing, microstructure and wear behaviour of silicon nitride hot-pressed with alumina and yttria, Journal of the American Ceramic Society77 (1994), No. 4, S. 88389010.1111/j.1151-2916.1994.tb07243.xSearch in Google Scholar

7 D.Wang, Z.Mao: Studies on abrasive wear of monolithic silicon nitride and a silicon carbide whiskers-reinforced silicon nitride composite, Journal of the American Ceramic Society78 (1995), No. 10, S. 2705270810.1111/j.1151-2916.1995.tb08045.xSearch in Google Scholar

8 W.Liu, J. L.Duda, E. E.Klaus: Wear property of silicon nitride in steel-on-Si3N4 and Si3N4-on- Si3N4 systems, Wear199 (1996), No. 2, S. 21722110.1016/0043-1648(96)06942-6Search in Google Scholar

9 X. Z.Zhao, J. J.Liu, B. L.Zhu, H. Z.Miao, Z. B.Luo: Friction and wear of Si3N4 ceramic/stainless steel. Sliding contact in dry and lubricated conditions, Journal of Materials Engineering and Performance6 (1997), No. 2, S. 20320810.1007/s11665-997-0015-2Search in Google Scholar

10 J.Takadoum, H.Houmid-Bannani, D.Mairey: The wear characteristics of silicon nitride. Journal of the European Ceramic Society18 (1998), No. 5, S. 55355610.1016/S0955-2219(97)00157-XSearch in Google Scholar

11 Z.Xingzhong, L.Jiajun, Z.Baoliang, M.Hezhou, L.Zhenbi: Wear behaviour of Si3N4 ceramic cutting tool material against stainless steel in dry water-lubricated conditions. Ceramics International25 (1999), No. 4, S. 30931510.1016/S0272-8842(98)00040-6Search in Google Scholar

12 J. R.Gomes, A. S.Miranda, R. F.Silva, J. M.Vieira: Tribooxidational effects on friction and wear behaviour of silicon nitride/tool steel and silicon nitride/grey cast iron contacts, Journal of the American Ceramic Society82 (1999), No. 4, S. 95396010.1111/j.1151-2916.1999.tb01859.xSearch in Google Scholar

13 J. R.Gomes, M. I.Osendi, P.Miranzo, F. J.Oli-veira, R. F.Silva: Tribological characteristics of self-mated couples of Si3N4-SiC composites in the range 22–700°C, Wear233–235 (1999), S. 22210.1016/S0043-1648(99)00243-4Search in Google Scholar

14 S. S.Kim, Y. H.Chae, D. J.Kim: Tribological characteristics of silicon nitride at elevated temperatures, Tribology Letters9 (2000) No. 3–4, S. 22723210.1023/A:1018873208419Search in Google Scholar

15 C. P.Doğan, J. A.Hawk: Microstructure and abrasive wear in silicon nitride ceramics, Wear250 (2001), No. 1, S. 25626310.1016/S0043-1648(01)00649-4Search in Google Scholar

16 M.Nakamura, K.Hirao, Y.Yamauchi, S.Kan-zaki: Tribological properties of unidirectionally aligned silicon nitride, Journal of the American Ceramic Society84 (2001), No. 11, S. 2579258410.1111/j.1151-2916.2001.tb01057.xSearch in Google Scholar

17 M.Košiarova, E.Rudnayova, J.Kovalčik, J.Dusza, M.Hnatko, P.Šajgalik, A.Marstallinger: Wear and creep characteristics of a carbon-derived Si3N4/SiC Micro/Nanokomposite, Materialwissenschaft und Werkstofftechnik34 (2003), No. 4, S. 33834210.1002/mawe.200390071Search in Google Scholar

18 J.Babcsán Kiss, M. M.Berkes: Investigation of the tribological behaviour of Si3N4 based ceramics, Materialwissenschaft und Werk-stofftechnik34 (2003), No. 4, S. 34334810.1002/mawe.200390072Search in Google Scholar

19 A.Kailer, T.Hollstein, G.Wötting, K.Berroth, J.Kozlowski: Tribologische Untersuchung von Siliciumnitrid für keramische Walzwerkzeuge, Tribologie und Schmierungstechnik51 (2004), No. 4, S. 2024Search in Google Scholar

20 M.Kašiarova, E.Rudnayová, J.Dusza, M.Hnatko, P.Šajgalik, A.Merstallinger, L.Kuzsella: Some tribological properties of a carbon-derived Si3N4/SiC nanocomposite, Journal of the European Ceramic Society24 (2004), S. 31313435Search in Google Scholar

21 K.Poser, J.Schneider, K.-H.Zum Gahr: Keramik/Metall-Friktionspaarungen unter ungeschmierter Gleitbeanspruchung bei kurzzeitiger Belastung, Materialwissenschaft und Werkstofftechnik35 (2004), No. 10/11, S. 79480010.1002/mawe.200400809Search in Google Scholar

22 R.Schober, D.Loibl: Einsatz keramischer Schneidstoffe in der Stanztechnik, Materialwissenschaft und Werkstofftechnik35 (2004), No. 10/11, S. 83083410.1002/mawe.200400787Search in Google Scholar

23 G.Wötting, R.Wagner, G.Martin, E.Streit: Qualitätssichere und zuverlässige Siliciumnitrid-Wälzkörper für hoch belastete Wälzlager, HTM Zeitschrift für Werkstoffe, Wärmebehandlung, Fertigung60 (2005), No. 2, S. 96103Search in Google Scholar

24 E.Carrasquero, A.Bellosi, M. H.Staia: Characterisation and wear behaviour of modified silicon nitride, International Journal of Refractory Metals and Hard Materials23 (2005), No. 4-6, S. 39139710.1016/j.ijrmhm.2005.06.004Search in Google Scholar

25 H.Hyuga, M. I.Jones, K.Hirao, Y.Yamauchi: Friction and wear properties of Si3N4/carbon fiber composites with aligned microstructure, Journal of the American Ceramic Society88 (2005), No. 5, S. 1239124310.1111/j.1551-2916.2005.00283.xSearch in Google Scholar

26 H.Hyuga, M. I.Jones, K.Hirao, Y.Yamauchi, K.Yoshida, H.Kita: The relationship between multiple scratch tests and wear behaviour of hot pressed silicon nitride ceramics with various rare-earth additive systems, Journal of the American Ceramic Society91 (2008), No. 1, S. 192197Search in Google Scholar

27 R.Danzer, T.Lube, P.Supancic, R.Damani: Fracture of ceramics. Advance Engi-neering Materials10 (2008), No. 4, S. 275298.10.1002/adem.200700347Search in Google Scholar

28 M.Belmonte, P.Miranzo, M. I.Osendi, J. R.Gomes: Wear of aligned silicon nitride under dry sliding conditions, Wear266 (2009), No. 1-2, S. 61210.1016/j.wear.2008.05.004Search in Google Scholar

29 H.Miyazaki, H.Hyuga, Y.Yoshizawa, K.Hirao, T.Ohji: Correlation of wear behaviour and indentation fracture resistance in silicon nitride ceramics hot-pressed with alumina and yttria, Journal of the European Ceramic Society29 (2009) 8, S. 1535154210.1016/j.jeurceramsoc.2008.08.020Search in Google Scholar

30 P.Tatarko, M.Kašiarova, J.Dusza, J.Morgiel, P.Šajgalik, P.Hvizdoš: Wear resistance of hot-pressed Si3N4/SiC micro/nanocomposites sintered with rare-earth oxide additives, Wear269 (2010), S. 86787410.1016/j.wear.2010.08.020Search in Google Scholar

31 A.Kailer, P. J.Mauk, C.Eckardt, K.Berroth, J.Kozlowski, A.Wagemann: Ceramic rolling tools for enhanced lifetime and product quali-ty. Steel Research International79 (2008), Special Edition of the Proc. of the Metal For-ming Conference 2008, Vol. 2, S. 401406Search in Google Scholar

32 R.Danzer, M.Lengauer, W.Zleppnig, W.Harrer: Silicon nitride tools for hot rolling of high-alloyed steel and superalloy wire–load analysis and first practical tests. International Journal of Materials Research98 (2007), No. 11, S. 11041114.10.3139/146.101575Search in Google Scholar

33 M.Lengauer, R.Danzer: Silicon nitride tools for the hot rolling of high-alloyed steel and superalloy wire–crack growth and lifetime prediction. Journal of the European Ceramic Society28 (2008), No. 11, S. 22892298.10.1016/j.jeurceramsoc.2008.02.028Search in Google Scholar

34 R.Danzer, M.Lengauer, D.Rubesa, W.Harrer: Silicon nitride tools for hot rolling of high-alloyed steel and superalloy wires. Key Engineering Materials409 (2009), S. 4354.10.4028/www.scientific.net/KEM.409.43Search in Google Scholar

35 M.Hermann, P.Obenaus, C.Schubert, D.Stephan, S.Keßler: Charakterisierung der Gefüge anisotroper Si3N4-Materialien, Praktische Metallographie, Sonderband No. 24. Carl Hanser Verlag München (1993), S. 253261Search in Google Scholar

36 S.Keßler, D.Stephan, J.Pabst, Chr. Schubert: Korntextur in heißgepreßtem Siliciumnitrid, Proc. DGM Jahrestagung (1991)Search in Google Scholar

37 F.Lee, K. J.Bowman: Texture and Anoso­-tropy in Silicon Nitride. Journal of the American Ceramic Society75 (1992), No. 7, S. 1748175510.1111/j.1151-2916.1992.tb07192.xSearch in Google Scholar

38 G.Ziegler: Microstructural aspects of thermal stress resistance of high-strength engineering ceramics Part II: Influence of microstructure on thermal shock resistance of high-strength engineering ceramics, Material­wissenschaft und Werkstofftechnik16 (1985), No. 2, S. 455510.1002/mawe.19850160206Search in Google Scholar

39 M.Schünemann, S.Waengler: Keramische Walzen für Walzdrähte–Wirtschaftlichkeit und Qualität, Proc. Fachsymposium Keramik für die Walztechnik 2009, Fraunhofer Verlag, Stuttgart (2009), S. 85–94Search in Google Scholar

40 L.Rozsnoki, V.Schreiner: Walzen von Profilen, Proc. Fachsymposium Keramik für die Walztechnik 2009, Fraunhofer Verlag, Stuttgart (2009), S. 149–157Search in Google Scholar

Online erschienen: 2013-05-26
Erschienen im Druck: 2011-11-01

© 2011, Carl Hanser Verlag, München

Downloaded on 22.10.2025 from https://www.degruyterbrill.com/document/doi/10.3139/120.110284/html
Scroll to top button