Adhesive wear behavior of FeB–FeMn–C coatings produced by GTAW
-
Mehmet Yaz
Assoc. Prof. Dr. Mehmet Yaz, born in 1962, completed his higher education in 1986 at the Gazi University Technical Education Faculty, Machining Department. In the fall of 1996, he started his graduate studies at the Institute of Science, Department of Mechanical Education. After completing his Master’s degree in 1999, he started his PhD at the Institute of Science, Department of Metallurgical Education. In 2005, he successfully completed his PhD. Currently, he is Associate Professor in the field of Materials and Metallurgical Engineering.
Abstract
In this paper, a high energy density beam of gas tungsten arc welding (GTAW) was employed to build a surface over low carbon steel with FeMn, FeB, and graphite powders. X-ray diffraction, optical microscopy, energy dispersive X-ray analysis, scanning electron microscopy, micro hardness tester, and adhesive wear tester were used for researching behavior of the composite coating which microstructure, hardness and dry-sliding wear. Many different carbides and borides, including Mn5C2, Fe3C, B8C, MnB, B4C, Fe3B, Fe7C3, FeB, and Mn2B, were found on the coated surfaces. The microstructure analysis shows that the shape of the graphite also depends on the FeMn–FeB–C content. The smallest weight loss was obtained from Sample S4 and the critical sliding distance was enhanced by adding graphite from 5 to 20 wt% at transition from oxidative to abrasive.
About the author
Assoc. Prof. Dr. Mehmet Yaz, born in 1962, completed his higher education in 1986 at the Gazi University Technical Education Faculty, Machining Department. In the fall of 1996, he started his graduate studies at the Institute of Science, Department of Mechanical Education. After completing his Master’s degree in 1999, he started his PhD at the Institute of Science, Department of Metallurgical Education. In 2005, he successfully completed his PhD. Currently, he is Associate Professor in the field of Materials and Metallurgical Engineering.
-
Author contributions: The author has accepted responsibility for the entire content of this submitted manuscript and approved submission.
-
Research funding: The author wishes to thank Firat University Scientific Research Projects Unit. This work was supported by FUBAP (Project No: 1809).
-
Conflict of interest statement: The author declares no conflicts of interest regarding this article.
References
[1] P. J. Modenesi, E. R. Apolinario, and I. M. Pereira, “TIG welding with single-component fluxes,” J. Mater. Process. Technol., vol. 99, nos. 1–3, pp. 260–265, 2000, https://doi.org/10.1016/S0924-0136(99)00435-5.Search in Google Scholar
[2] S. Ozel, B. Kurt, I. Somunkiran, and N. Orhan, “Microstructural characteristic of NiTi coating on stainless steel by plasma transferred arc process,” Surf. Coat. Technol., vol. 202, no. 15, pp. 3633–3637, 2008, https://doi.org/10.1016/j.surfcoat.2008.01.006.Search in Google Scholar
[3] T. Teker and D. Gencdogan, “Heat affected zone and weld metal analysis of HARDOX 450 and ferritic stainless steel double sided TIG-joints,” Mater. Test., vol. 63, no. 10, pp. 923–928, 2021, https://doi.org/10.1515/mt-2021-0022.Search in Google Scholar
[4] C. M. Chang, C. M. Lin, C. C. Hsieh, J. H. Chen, and W. Wu, “Microstructural characteristics of Fe–40wt%Cr–xC hardfacing alloys with [1.0–4.0 wt%] carbon content,” J. Alloys Compd., vol. 487, nos. 1–2, pp. 83–89, 2009, https://doi.org/10.1016/j.jallcom.2009.07.134.Search in Google Scholar
[5] I. Kirik, Z. Balalan, A. Imak, and M. Yaz, “Properties of different TIG coatings of stellite on the hardox 450 and St 52 steel,” Mater. Test., vol. 62, no. 11, pp. 1089–1093, 2020, https://doi.org/10.3139/120.111590.Search in Google Scholar
[6] S. O. Yılmaz, “Wear behavior of gas tungsten arc deposited FeCrC, FeCrSi, and WCo coatings on AISI 1018 steel,” Surf. Coat. Technol., vol. 194, nos. 2–3, pp. 175–183, 2005, https://doi.org/10.1016/j.surfcoat.2004.08.227.Search in Google Scholar
[7] M. Ginting, J. Pane, D. H. Simbolon, et al., “The effect of FeMn and FeB additive on hematite (α-Fe2O3) and their characterization,” in 2018 International Symposium on Frontier of Applied Physics, Journal of Physics: Conference Series, Banten, Indonesia, vol. 1191, IOP Publishing, 2019, pp. 1–6.10.1088/1742-6596/1191/1/012035Search in Google Scholar
[8] J. Hufenbach, H. Wendrock, F. Kochta, U. Kühn, and A. Gebert, “Novel biodegradable Fe-Mn-C-S alloy with superior mechanical and corrosion properties,” Mater. Lett., vol. 186, pp. 330–333, 2017, https://doi.org/10.1016/j.matlet.2016.10.037.Search in Google Scholar
[9] O. Bouaziz, S. Allain, C. Scott, P. Cugy, and D. Barbier, “High manganese austenitic twinning induced plasticity steels: a review of the microstructure properties relationships,” Curr. Opin. Solid State Mater. Sci., vol. 15, no. 4, pp. 141–168, 2011, https://doi.org/10.1016/j.cossms.2011.04.002.Search in Google Scholar
[10] Z. Y. Ma, S. C. Tjong, and L. Gen, “In-situ Ti–TiB metal–matrix composite prepared by a reactive pressing process,” Scr. Mater., vol. 42, no. 4, pp. 367–373, 2000, https://doi.org/10.1016/S1359-6462(99)00354-1.Search in Google Scholar
[11] S. O. Yılmaz, M. Ozenbas, and M. Yaz, “Synthesis of TiB2-reinforced iron-based composite coating,” Tribol. Int., vol. 42, no. 8, pp. 1220–1229, 2009, https://doi.org/10.1016/j.triboint.2009.04.041.Search in Google Scholar
[12] L. Bourithis, S. Papaefthymiou, and G. D. Papadimitriou, “Plasma transferred arc boriding of a low carbon steel: microstructure and wear properties,” Appl. Surf. Sci., vol. 200, nos. 1–4, pp. 203–218, 2002, https://doi.org/10.1016/S0169-4332(02)00901-7.Search in Google Scholar
[13] A. Aliyu and C. Srivastava, “Morphology and corrosion properties of FeMn-Graphene oxide composite coatings,” J. Alloys Compd., vol. 821, pp. 1–6, 2020. https://doi.org/10.1016/j.jallcom.2019.153560.Search in Google Scholar
[14] T. Teker and A. Topal, “Properties and chemical composition of plasma arc welded Hardox450+FeW coatings,” Mater. Test., vol. 61, no. 1, pp. 35–40, 2019, https://doi.org/10.3139/120.111278.Search in Google Scholar
[15] H. Berns, “Microstructural properties of wear-resistant alloys,” Wear, vols. 181–183, no. P1, pp. 271–279, 1995, https://doi.org/10.1016/0043-1648(95)90034-9.Search in Google Scholar
[16] M. Kirchgaßner, E. Badisch, and F. Franek, “Behaviour of iron-based hardfacing alloys under abrasion and impact,” Wear, vol. 265, nos. 5–6, pp. 772–779, 2008, https://doi.org/10.1016/j.wear.2008.01.004.Search in Google Scholar
[17] X. Wu and G. Chen, “Nonequilibrium microstructures and their evolution in a Fe–Cr–W–Ni–C laser clad coating,” Material Sci. Eng., vol. 270, no. 2, pp. 183–189, 1999, https://doi.org/10.1016/S0921-5093(99)00159-8.Search in Google Scholar
[18] L. Zhang, B. Liu, H. Yu, and D. Sun, “Rapidly solidified non-equilibrium microstructure and phase transformation of plasma cladding Fe-based alloy coating,” Surf. Coat. Technol., vol. 201, no. 12, pp. 5931–5936, 2007, https://doi.org/10.1016/j.surfcoat.2006.10.050.Search in Google Scholar
[19] M. Eroglu, “Boride coatings on steel using shielded metal arc welding electrode: microstructure and hardness,” Surf. Coat. Technol., vol. 203, no. 16, pp. 2229–2235, 2009, https://doi.org/10.1016/j.surfcoat.2009.02.010.Search in Google Scholar
[20] C. L. Ge and R. C. Ye, “Research on self-propagating eutectic boriding,” J. Mater. Process. Technol., vol. 124, nos. 1–2, pp. 14–18, 2002, https://doi.org/10.1016/S0924-0136(01)01027-5.Search in Google Scholar
[21] M. Yaz, “In situ formation of square shaped Fe2B borides in coated surface produced by GTAW,” J. Optoelectron. Adv. Mater., vol. 15, nos. 9–10, pp. 1037–1046, 2013.Search in Google Scholar
[22] M. Yaz, “Adhesive wear behavior of gas tungsten arc welded FeB-FeMo-C coatings,” Mater. Test., vol. 64, no. 2, pp. 228–239, 2022, https://doi.org/10.1515/mt-2021-2001.Search in Google Scholar
© 2023 Walter de Gruyter GmbH, Berlin/Boston
Articles in the same Issue
- Frontmatter
- Innovative prevention of stress corrosion crack propagation in nuclear power pipe welds
- A new manufacturing process for allogeneic bone plates based on high hydrostatic pressure–treated granules for jaw augmentation
- Effects of Mn and Cu on descaling of hot-rolled 304L stainless steel in HCl and H2O2 mixtures
- Development of morphology and lattice misfit in modified Ni-base superalloy with Al, Co and Ni additions
- Adhesive wear behavior of FeB–FeMn–C coatings produced by GTAW
- Approximation of the stiffness of laminate stacks of electric motors subjected to cyclic loads
- Microstructure development and mechanical behaviour of pure copper processed by the novel TWO-CAP procedure
- Composite disc optimization using hunger games search optimization algorithm
- Cheetah optimization algorithm for optimum design of heat exchangers
- Influence of Ti and Nb addition on the microstructure, mechanical, and machinability properties of 316L stainless steel fabricated by powder metallurgy
- Effect of impactor nose form on the impact behavior of reinforced composite materials
- Optimization of cutting parameters by thrust force and time for drilling of aluminum 2024 T351
- Effect of curvature and stacking sequence on flexural strength in glass fiber reinforced composites
- Influence of tool pin shape and rotation speed for friction stir spot welding of AZ91 magnesium alloy sheets
- Corrigendum to: Mechanical properties and wear-corrosion resistance of a new compound extrusion process for magnesium alloy AZ61
Articles in the same Issue
- Frontmatter
- Innovative prevention of stress corrosion crack propagation in nuclear power pipe welds
- A new manufacturing process for allogeneic bone plates based on high hydrostatic pressure–treated granules for jaw augmentation
- Effects of Mn and Cu on descaling of hot-rolled 304L stainless steel in HCl and H2O2 mixtures
- Development of morphology and lattice misfit in modified Ni-base superalloy with Al, Co and Ni additions
- Adhesive wear behavior of FeB–FeMn–C coatings produced by GTAW
- Approximation of the stiffness of laminate stacks of electric motors subjected to cyclic loads
- Microstructure development and mechanical behaviour of pure copper processed by the novel TWO-CAP procedure
- Composite disc optimization using hunger games search optimization algorithm
- Cheetah optimization algorithm for optimum design of heat exchangers
- Influence of Ti and Nb addition on the microstructure, mechanical, and machinability properties of 316L stainless steel fabricated by powder metallurgy
- Effect of impactor nose form on the impact behavior of reinforced composite materials
- Optimization of cutting parameters by thrust force and time for drilling of aluminum 2024 T351
- Effect of curvature and stacking sequence on flexural strength in glass fiber reinforced composites
- Influence of tool pin shape and rotation speed for friction stir spot welding of AZ91 magnesium alloy sheets
- Corrigendum to: Mechanical properties and wear-corrosion resistance of a new compound extrusion process for magnesium alloy AZ61
