Comparison of pull-out behavior of glass, basalt, and carbon rovings embedded in fine-grain concrete and geopolymer
-
Till Quadflieg
and
Oleg Stolyarov
Abstract
In this work, we studied the pull-out behavior of glass, basalt, and carbon rovings embedded in fine-grain concrete and geopolymer. Smooth rovings from the bobbin and coated rovings extracted from the fabric were both studied. A matrix made of fine-grained concrete and geopolymer was used to determine the interaction between roving and matrix during pull-out. The use of these matrices provides an economical consumption of concrete used in building structures. In addition, the bonding effect between coated roving and matrix was also investigated. As a result, it was observed that the bonding strength in a matrix made of fine-grained concrete is higher than that of a geopolymer. Smooth roving exhibited a minimal bonding characteristic irrespective of the matrix. The best anchoring is achieved by the coated roving extracted from the fabric and the strength characteristics of the roving itself are not critical.
-
Author contributions: All the authors have accepted responsibility for the entire content of this submitted manuscript and approved submission.
-
Research funding: None declared.
-
Conflict of interest statement: The authors declare no conflicts of interest regarding this article.
References
[1] T. Gries, M. Raina, T. Quadflieg, and O. Stolyarov, “Manufacturing of textiles for civil engineering applications,” in Textile Fiber Composites in Civil Engineering, T. Triantafillou, Ed., Cambridge, Elsevier, 2016, pp. 3–24.10.1016/B978-1-78242-446-8.00002-1Search in Google Scholar
[2] M. Motavalli, C. Czaderski, A. Schumacher, and D. Gsell, “Fibre reinforced polymer composite materials for building and construction,” in Textiles, Polymers and Composites for Buildings, G. Pohl, Ed., Cambridge, Woodhead Publishing, 2010, pp. 69–128.10.1533/9780845699994.1.69Search in Google Scholar
[3] K. Mahato, K. Dutta, and B. Ray, “Emerging advancement of fiber-reinforced polymer composites in structural applications,” in New Materials in Civil Engineering, P. Samui, D. Dookie Kim, and S. Chaudhary, Eds., Oxford, Butterworth-Heinemann, 2020, pp. 221–271.10.1016/B978-0-12-818961-0.00006-5Search in Google Scholar
[4] M. Bakhaled, M. Bentchikou, R. Belarbi, and M. Maliki, “Elaboration and characterization of extruded clay bricks with light weight date palm fibers,” Mater. Test., vol. 63, no. 9, pp. 872–877, 2021, https://doi.org/10.1515/mt-2021-0011.Search in Google Scholar
[5] F. Zhu, P. Bai, and D. Lei, “Measurement of tensile mechanical properties of fiber reinforced plastic rebars by 3D digital image correlation,” Mater. Test., vol. 62, no. 4, pp. 422–428, 2020, https://doi.org/10.3139/120.111501.Search in Google Scholar
[6] H. Acikel, “Mechanical properties of hybrid fiber reinforced concrete and a nondestructive evaluation,” Mater. Test., vol. 61, no. 12, pp. 1171–1177, 2019, https://doi.org/10.3139/120.111438.Search in Google Scholar
[7] T. Triantafillou, “Strengthening of existing concrete structures: concepts and structural behavior,” in Textile Fiber Composites in Civil Engineering, T. Triantafillou, Ed., Cambridge, Elsevier, 2016, pp. 303–322.10.1016/B978-1-78242-446-8.00014-8Search in Google Scholar
[8] F. Micelli, A. Renni, A. Kandalaft, and S. Moro, “Fiber-reinforced concrete and ultrahigh-performance fiber-reinforced concrete materials,” in New Materials in Civil Engineering, P. Samui, D. Dookie Kim, and S. Chaudhary, Eds., Oxford, Butterworth-Heinemann, 2020, pp. 273–314.10.1016/B978-0-12-818961-0.00007-7Search in Google Scholar
[9] M. Halvaei, M. Jamshidi, M. Latifi, and M. Ejtemaei, “Experimental investigation and modelling of flexural properties of carbon textile reinforced concrete,” Construct. Build. Mater., vol. 262, 2020, Art no. 120877, https://doi.org/10.1016/J.CONBUILDMAT.2020.120877.Search in Google Scholar
[10] A. Peled, A. Bentur, and B. Mobasher, Textile Reinforced Concrete, Boca Raton, CRC Press, Taylor and Francis Group, 2017.10.1201/9781315119151Search in Google Scholar
[11] M. Khan, F. Sanchez, and H. Zhou, “3-D printing of concrete: beyond horizons,” Cem. Concr. Res., vol. 133, 2020, Art no. 106070, https://doi.org/10.1016/J.CEMCONRES.2020.106070.Search in Google Scholar
[12] A. Scholzen, R. Chudoba, and J. Hegger, “Thin-walled shell structures made of textile-reinforced concrete: part I: structural design and construction,” Struct. Concr., vol. 16, no. 1, pp. 106–114, 2015, https://doi.org/10.1002/suco.201300071.Search in Google Scholar
[13] J. Hegger, C. Kulas, and M. Horstmann, “Spatial textile reinforcement structures for ventilated and sandwich facade elements,” Adv. Struct. Eng., vol. 15, no. 4, pp. 665–675, 2012, https://doi.org/10.1260/1369-4332.15.4.665.Search in Google Scholar
[14] J. Hartig, U. Häußler-Combe, and K. Schicktanz, “Influence of bond properties on the tensile behaviour of textile reinforced concrete,” Cement Concr. Compos., vol. 30, no. 10, pp. 898–906, 2008, https://doi.org/10.1016/J.CEMCONCOMP.2008.08.004.Search in Google Scholar
[15] A. Peled, S. Sueki, and B. Mobasher, “Bonding in fabric–cement systems: effects of fabrication methods,” Cem. Concr. Res., vol. 36, no. 9, pp. 1661–1671, 2006, https://doi.org/10.1016/j.cemconres.2006.05.009.Search in Google Scholar
[16] B. Banholzer, “Bond of a strand in a cementitious matrix,” Mater. Struct., vol. 39, no. 10, pp. 1015–1028, 2006, https://doi.org/10.1617/s11527-006-9115-y.Search in Google Scholar
[17] S. Raoof, L. Koutas, and D. Bournas, “Bond between textile-reinforced mortar (TRM) and concrete substrates: experimental investigation,” Compos. B Eng., vol. 98, pp. 350–361, 2016, https://doi.org/10.1016/j.compositesb.2016.05.041.Search in Google Scholar
[18] A. Peled, E. Zaguri, and G. Marom, “Bonding characteristics of multifilament polymer yarns and cement matrices,” Compos. A Appl. Sci. Manuf., vol. 39, no. 6, pp. 930–939, 2008, https://doi.org/10.1016/j.compositesa.2008.03.012.Search in Google Scholar
[19] A. Peled, S. Sueki, and B. Mobasher, “Bonding in fabric–cement systems: effects of fabrication methods,” Cem. Concr. Res., vol. 36, no. 9, pp. 1661–1671, 2006, https://doi.org/10.1016/j.cemconres.2006.05.009.Search in Google Scholar
[20] A. Bentur, A. Peled, and D. Yankelevsky, “Enhanced bonding of low modulus polymer fibers-cement matrix by means of crimped geometry,” Cem. Concr. Res., vol. 27, no. 7, pp. 1099–1111, 1997, https://doi.org/10.1016/S0008-8846(97)00088-4.Search in Google Scholar
[21] B. Fiorio, H. Aljewifi, and J. Gallias, “Connection between the impregnation of glass multi-filament yarns and their pull-out behaviour,” in Textilbeton in Theorie und Praxis: Tagungsband zum 6. Kolloquium zu Textilbewehrten Tragwerken, M. Curbach, and R. Ortlepp, Eds., Dresden, Germany, Technische Universität Dresden, 2011, pp. 41–60.Search in Google Scholar
[22] J. Hegger, N. Will, O. Bruckermann, and S. Voss, “Load–bearing behaviour and simulation of textile reinforced concrete,” Mater. Struct., vol. 39, no. 8, pp. 765–776, 2006, https://doi.org/10.1617/s11527-005-9039-y.Search in Google Scholar
[23] A. Peled, A. Bentur, and D. Yankelevsky, “Effects of woven fabric geometry on the bonding performance of cementitious composites,” Adv. Cement Base. Mater., vol. 7, no. 1, pp. 20–27, 1998, https://doi.org/10.1016/S1065-7355(97)00012-6.Search in Google Scholar
[24] S. Xu, M. Krüger, H.-W. Reinhardt, and J. Ožbolt, “Bond characteristics of carbon, alkali resistant glass, and aramid textiles in mortar,” J. Mater. Civ. Eng., vol. 16, no. 4, pp. 356–364, 2004, https://doi.org/10.1061/(ASCE)0899-1561(2004)16:4(356).10.1061/(ASCE)0899-1561(2004)16:4(356)Search in Google Scholar
[25] B. Banholzer, W. Brameshuber, and W. Jung, “Analytical simulation of pull-out tests—the direct problem,” Cement Concr. Compos., vol. 27, no. 1, pp. 93–101, 2005, https://doi.org/10.1016/j.cemconcomp.2004.01.006.Search in Google Scholar
[26] B. Banholzer, T. Brockmann, and W. Brameshuber, “Material and bonding characteristics for dimensioning and modelling of textile reinforced concrete (TRC) elements,” Mater. Struct., vol. 39, no. 8, pp. 749–763, 2006, https://doi.org/10.1617/s11527-006-9140-x.Search in Google Scholar
[27] M. Butler, R. Hempel, and H. Schorn, “Bond behavior of polymer impregnated AR-glass textile reinforcement in concrete,” in International Symposium – Polymers in Concrete (ISPIC), Guimaraes, Portugal, University of Minho, 2006, pp. 173–183.Search in Google Scholar
[28] B. Zastrau, M. Richter, and I. Lepenies, “On the analytical solution of pullout phenomena in textile reinforced concrete,” J. Eng. Mater. Technol., vol. 125, no. 1, pp. 38–43, 2003, https://doi.org/10.1115/1.1526125.Search in Google Scholar
[29] A. Ganesh and M. Muthukannan, “Development of high performance sustainable optimized fiber reinforced geopolymer concrete and prediction of compressive strength,” J. Clean. Prod., vol. 282, 2020, Art no. 124543, https://doi.org/10.1016/J.JCLEPRO.2020.124543.Search in Google Scholar
[30] K. Korniejenko and M. Łach, “Geopolymers reinforced by short and long fibres – innovative materials for additive manufacturing,” Curr. Opin. Chem. Eng., vol. 28, pp. 167–172, 2020, https://doi.org/10.1016/J.COCHE.2020.06.005.Search in Google Scholar
[31] I. Perná, T. Hanzlíček, P. Boura, and A. Lučaník, “Application of a clay-slag geopolymer matrix for repairing damaged concrete: laboratory and industrial-scale experiments,” Mater. Test., vol. 59, no. 10, pp. 929–937, 2017, https://doi.org/10.3139/120.111090.Search in Google Scholar
[32] J. Provis and J. van Deventer, Geopolymer: Structure, Processing, Properties and Industrial Applications, Camdridge, Woodhead Publishing, 2009.10.1533/9781845696382Search in Google Scholar
[33] P. Aitcin and S. Mindess, Sustainability of Concrete, New York, USA, Spon Press, 2011.10.1201/9781482266696Search in Google Scholar
[34] P. Duxson, J. Provis, G. Lukey, and J. van Deventer, “The role of inorganic polymer technology in the development of ‘green concrete’,” Cem. Concr. Res., vol. 37, no. 12, pp. 1590–1597, 2007, https://doi.org/10.1016/J.CEMCONRES.2007.08.018.Search in Google Scholar
[35] S. Aydın, “A ternary optimisation of mineral additives of alkali activated cement mortars,” Construct. Build. Mater., vol. 43, pp. 131–138, 2013, https://doi.org/10.1016/J.CONBUILDMAT.2013.02.005.Search in Google Scholar
© 2022 Walter de Gruyter GmbH, Berlin/Boston
Articles in the same Issue
- Frontmatter
- Experimental and dynamic thermal numerical investigation of a climate test chamber
- Influence of high-temperature, high-pressure, and acidic conditions on the structure and properties of high-performance organic fibers
- Microstructure analysis and mechanical properties of electron beam powder bed fusion (PBF-EB)-manufactured γ-titanium aluminide (TiAl) at elevated temperatures
- Microstructural evolution and impression creep properties of a lead-based alloy PbSn16Sb16Cu2
- Laser and TIG welding of additive manufactured Ti-6Al-4V parts
- Investigation of the hydrogen embrittlement susceptibility of steel components during thin-film hot-dip galvanizing
- Effects of coating, holding force, stretching height, yield stress, and surface roughness on springback of steel in the V-stretch bending test
- Gradient-based optimizer for economic optimization of engineering problems
- Failure investigation of a spline half-shaft in a loader rickshaw differential system
- Manta ray foraging optimization algorithm and hybrid Taguchi salp swarm-Nelder–Mead algorithm for the structural design of engineering components
- Effect of tool rotational speed and position on mechanical and microstructural properties of friction stir welded dissimilar alloys AZ31B Mg and Al6061
- Effect of different joint angles on the mechanical strength of adhesive-bonded scarf and double butt–lap joints
- Buckling behavior of laminated composites with embedded delaminations
- Comparison of pull-out behavior of glass, basalt, and carbon rovings embedded in fine-grain concrete and geopolymer
Articles in the same Issue
- Frontmatter
- Experimental and dynamic thermal numerical investigation of a climate test chamber
- Influence of high-temperature, high-pressure, and acidic conditions on the structure and properties of high-performance organic fibers
- Microstructure analysis and mechanical properties of electron beam powder bed fusion (PBF-EB)-manufactured γ-titanium aluminide (TiAl) at elevated temperatures
- Microstructural evolution and impression creep properties of a lead-based alloy PbSn16Sb16Cu2
- Laser and TIG welding of additive manufactured Ti-6Al-4V parts
- Investigation of the hydrogen embrittlement susceptibility of steel components during thin-film hot-dip galvanizing
- Effects of coating, holding force, stretching height, yield stress, and surface roughness on springback of steel in the V-stretch bending test
- Gradient-based optimizer for economic optimization of engineering problems
- Failure investigation of a spline half-shaft in a loader rickshaw differential system
- Manta ray foraging optimization algorithm and hybrid Taguchi salp swarm-Nelder–Mead algorithm for the structural design of engineering components
- Effect of tool rotational speed and position on mechanical and microstructural properties of friction stir welded dissimilar alloys AZ31B Mg and Al6061
- Effect of different joint angles on the mechanical strength of adhesive-bonded scarf and double butt–lap joints
- Buckling behavior of laminated composites with embedded delaminations
- Comparison of pull-out behavior of glass, basalt, and carbon rovings embedded in fine-grain concrete and geopolymer
