Home Texture evolution in equiaxed polycrystalline L10-ordered FePd during coarsening at 600 °C
Article
Licensed
Unlicensed Requires Authentication

Texture evolution in equiaxed polycrystalline L10-ordered FePd during coarsening at 600 °C

  • A. R. Deshpande and J. M. K. Wiezorek EMAIL logo
Published/Copyright: January 11, 2022
Become an author with De Gruyter Brill
Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 97 Issue 3

Abstract

The texture evolution in equiaxed polycrystalline L10-FePd during the coarsening regime of annealing at 600 °C after cold-rolling has been investigated, using X-ray diffraction and scanning electron microscopy. A change in dominant texture was observed. Using the nomenclature established for texture description of face-centered cubic metals, the texture of the L10-FePd develops from a brass-type texture into a strong cube-type texture during coarsening. Also, a large density of special high-angle grain boundaries emerged during coarsening, which can be described as coherent Σ2-boundaries and are associated with (90 ± 5)°-rotations about a common cube-axis between the neighboring grains. The emergence of Σ2-boundaries may play an important role for previously reported abnormalities in the grain growth kinetics.

Keywords: L10-order; FePd; Orientation Imaging Microscopy; Texture; Grain coarsening
Jörg M. K. Wiezorek Associate Professor and William Kepler Whiteford Faculty Fellow Graduate Program Coordinator of Materials Science and Engineering University of Pittsburgh 848 Benedum Hall, Pittsburgh, PA 15261, USA Tel.: +1 412 624 0122 Fax: +1 412 624 8069

A. R. Deshpande, J. M. K. Wiezorek: Texture evolution in equiaxed polycrystalline L10-ordered FePd during coarsening

Dedicated to Professor Dr. Gernot Kostorz on the occasion of his 65th birthday

This material is based upon work supported by the National Science Foundation under Grant No. NSF0094213. Any opinions, findings and conclusions or recommendations expressed in this material are those of the authors and do not necessarily reflect the views of the National Science Foundation. We thank the editors of this special issue of Zeitschrift für Metallkunde for the opportunity of making this contribution on the occasion of Professor Kostorz’s 65th birthday.

References

[1] D. Weller, A. Moser: IEEE Trans. Magn. 35 (1999) 4423.10.1109/20.809134Search in Google Scholar

[2] B. Zhang, M. Lelovic, W.A. Soffa: Scr. Metall. Mater. 25 (1991) 1577.10.1016/0956-716X(91)90455-ASearch in Google Scholar

[3] B. Zhang: PhD Thesis, University of Pittsburgh (1991).Search in Google Scholar

[4] T. Klemmer, D. Hoydick, H. Okumura, B. Zhang,W.A. Soffa: Scr. Metall. Mater. 33 (1995) 1793.10.1016/0956-716X(95)00413-PSearch in Google Scholar

[5] T. Klemmer, W.A. Soffa: Solid-Solid phase transformations. TMS, Warrendale (1994) 969Search in Google Scholar

[6] A.R. Deshpande, J.M.K. Wiezorek: J. Magn. Magn. Mater. 270 (2004) 157.10.1016/j.jmmm.2003.08.013Search in Google Scholar

[7] J.M.K. Wiezorek, A.R. Deshpande: Mater. Res. Soc. Symp. Proc. 842 (2005) S3.9.1.10.1557/PROC-842-S3.9Search in Google Scholar

[8] J.S. Kallend, in: U.F. Kocks, C.N. Tome, H.R. Wenk (Eds.), Texture and Anisotropy – Preferred Orientations in Polycrystals and their Effect on Materials Properties, Chapter 3, Cambridge University Press, Cambridge, U.K (1998) 114–119.Search in Google Scholar

[9] J. Hirsch, K. Lücke: Acta Metall. 36 (1988) 2863.10.1016/0001-6160(88)90172-1Search in Google Scholar

[10] A.R. Deshpande, J.R. Blachere, J.M.K. Wiezorek: Scr. Mater. 54 (2006) 955.10.1016/j.scriptamat.2005.10.026Search in Google Scholar

[11] J.M.K. Wiezorek, A.R. Deshpande: Mater. Res. Soc. Symp. Proc. 842 (2005) S5.1.10.1557/PROC-842-S3.9Search in Google Scholar

[12] M. Yamaguchi, Y. Umakoshi: Progress in Mater. Sci. 34 (1990) 1.10.1016/0079-6425(90)90002-QSearch in Google Scholar

[13] V. Randle, O. Engler: Introduction to Texture analysis – Macrotexture, Microtexture & Orientation Mapping, Taylor & Francis Ltd, Bristol, UK (2003).Search in Google Scholar

[14] A.G. Khachaturyan: Theory of Structural Transformations in Solids, John Wiley and Sons, New York, NY (1983) 369.Search in Google Scholar
Received: 2005-10-20
Accepted: 2005-12-05
Published Online: 2022-01-11

© 2006 Carl Hanser Verlag, München

Articles in the same Issue

  1. Frontmatter
  2. Professor Dr. Gernot Kostorz 65 years
  3. Dislocation micromechanisms under single slip conditions
  4. Characterisation of short-range order using dislocations
  5. Between microscopic and mesoscopic descriptions of twin–twin interaction
  6. Influence of the thermoelastic effect on the acoustic properties of pure metals at low temperatures
  7. Recent progress in the area of bulk metallic glasses
  8. Formation of the ABC6-type ordered structure in fcc alloys
  9. Short-range order in Fe-21.9 at.% Al
  10. Criteria for developing castable, creep-resistant aluminum-based alloys – A review
  11. Phase decomposition and precipitation of metastable A2 phase in B2 ordered Co–Al–Fe alloys
  12. Atomic migration and ordering phenomena in bulk and thin films of FePd and FePt
  13. Late-stage coarsening of oil droplets of excess oil in microemulsions following a temperature quench
  14. Small-angle scattering from spherical particles on randomly oriented interfaces
  15. Ripening of L12 Ni3Ti precipitates in the framework of the trans-interface diffusion-controlled theory of particle coarsening
  16. Texture evolution in equiaxed polycrystalline L10-ordered FePd during coarsening at 600 °C
  17. Modulated structures in amorphous films of Cr-silicide prepared by electron-beam-deposition
  18. Early stages of nucleation and growth of Guinier –Preston zones in Al–Zn–Mg and Al–Zn–Mg–Cu alloys
  19. Experimental and theoretical characterization of Al3Sc precipitates in Al–Mg–Si–Cu–Sc–Zr alloys
  20. Ag2Al plates in Al–Ag alloys
  21. A critical analysis of the composite model as applied to high-temperature creep of Al and an Al–Mg alloy
  22. Damage behaviour of an Al2O3 particle-reinforced 6061 alloy induced by monotonic and cyclic deformation
  23. Deformation behaviour of ultrafine-grained magnesium with 3 vol.% graphite
  24. Press/Presse
  25. Conferences/Konferenzen
  26. Frontmatter
  27. Editorial
  28. Professor Dr. Gernot Kostorz 65 years
  29. Articles BBasic
  30. Dislocation micromechanisms under single slip conditions
  31. Characterisation of short-range order using dislocations
  32. Between microscopic and mesoscopic descriptions of twin–twin interaction
  33. Influence of the thermoelastic effect on the acoustic properties of pure metals at low temperatures
  34. Recent progress in the area of bulk metallic glasses
  35. Formation of the ABC6-type ordered structure in fcc alloys
  36. Short-range order in Fe-21.9 at.% Al
  37. Criteria for developing castable, creep-resistant aluminum-based alloys – A review
  38. Phase decomposition and precipitation of metastable A2 phase in B2 ordered Co–Al–Fe alloys
  39. Atomic migration and ordering phenomena in bulk and thin films of FePd and FePt
  40. Late-stage coarsening of oil droplets of excess oil in microemulsions following a temperature quench
  41. Small-angle scattering from spherical particles on randomly oriented interfaces
  42. Ripening of L12 Ni3Ti precipitates in the framework of the trans-interface diffusion-controlled theory of particle coarsening
  43. Articles AApplied
  44. Texture evolution in equiaxed polycrystalline L10-ordered FePd during coarsening at 600 °C
  45. Modulated structures in amorphous films of Cr-silicide prepared by electron-beam-deposition
  46. Early stages of nucleation and growth of Guinier –Preston zones in Al–Zn–Mg and Al–Zn–Mg–Cu alloys
  47. Experimental and theoretical characterization of Al3Sc precipitates in Al–Mg–Si–Cu–Sc–Zr alloys
  48. Ag2Al plates in Al–Ag alloys
  49. A critical analysis of the composite model as applied to high-temperature creep of Al and an Al–Mg alloy
  50. Damage behaviour of an Al2O3 particle-reinforced 6061 alloy induced by monotonic and cyclic deformation
  51. Deformation behaviour of ultrafine-grained magnesium with 3 vol.% graphite
  52. Notifications/Mitteilungen
  53. Press/Presse
  54. Conferences/Konferenzen
https://doi.org/10.1515/ijmr-2006-0048
Keywords for this article
L10-order; FePd; Orientation Imaging Microscopy; Texture; Grain coarsening

Articles in the same Issue

  1. Frontmatter
  2. Professor Dr. Gernot Kostorz 65 years
  3. Dislocation micromechanisms under single slip conditions
  4. Characterisation of short-range order using dislocations
  5. Between microscopic and mesoscopic descriptions of twin–twin interaction
  6. Influence of the thermoelastic effect on the acoustic properties of pure metals at low temperatures
  7. Recent progress in the area of bulk metallic glasses
  8. Formation of the ABC6-type ordered structure in fcc alloys
  9. Short-range order in Fe-21.9 at.% Al
  10. Criteria for developing castable, creep-resistant aluminum-based alloys – A review
  11. Phase decomposition and precipitation of metastable A2 phase in B2 ordered Co–Al–Fe alloys
  12. Atomic migration and ordering phenomena in bulk and thin films of FePd and FePt
  13. Late-stage coarsening of oil droplets of excess oil in microemulsions following a temperature quench
  14. Small-angle scattering from spherical particles on randomly oriented interfaces
  15. Ripening of L12 Ni3Ti precipitates in the framework of the trans-interface diffusion-controlled theory of particle coarsening
  16. Texture evolution in equiaxed polycrystalline L10-ordered FePd during coarsening at 600 °C
  17. Modulated structures in amorphous films of Cr-silicide prepared by electron-beam-deposition
  18. Early stages of nucleation and growth of Guinier –Preston zones in Al–Zn–Mg and Al–Zn–Mg–Cu alloys
  19. Experimental and theoretical characterization of Al3Sc precipitates in Al–Mg–Si–Cu–Sc–Zr alloys
  20. Ag2Al plates in Al–Ag alloys
  21. A critical analysis of the composite model as applied to high-temperature creep of Al and an Al–Mg alloy
  22. Damage behaviour of an Al2O3 particle-reinforced 6061 alloy induced by monotonic and cyclic deformation
  23. Deformation behaviour of ultrafine-grained magnesium with 3 vol.% graphite
  24. Press/Presse
  25. Conferences/Konferenzen
  26. Frontmatter
  27. Editorial
  28. Professor Dr. Gernot Kostorz 65 years
  29. Articles BBasic
  30. Dislocation micromechanisms under single slip conditions
  31. Characterisation of short-range order using dislocations
  32. Between microscopic and mesoscopic descriptions of twin–twin interaction
  33. Influence of the thermoelastic effect on the acoustic properties of pure metals at low temperatures
  34. Recent progress in the area of bulk metallic glasses
  35. Formation of the ABC6-type ordered structure in fcc alloys
  36. Short-range order in Fe-21.9 at.% Al
  37. Criteria for developing castable, creep-resistant aluminum-based alloys – A review
  38. Phase decomposition and precipitation of metastable A2 phase in B2 ordered Co–Al–Fe alloys
  39. Atomic migration and ordering phenomena in bulk and thin films of FePd and FePt
  40. Late-stage coarsening of oil droplets of excess oil in microemulsions following a temperature quench
  41. Small-angle scattering from spherical particles on randomly oriented interfaces
  42. Ripening of L12 Ni3Ti precipitates in the framework of the trans-interface diffusion-controlled theory of particle coarsening
  43. Articles AApplied
  44. Texture evolution in equiaxed polycrystalline L10-ordered FePd during coarsening at 600 °C
  45. Modulated structures in amorphous films of Cr-silicide prepared by electron-beam-deposition
  46. Early stages of nucleation and growth of Guinier –Preston zones in Al–Zn–Mg and Al–Zn–Mg–Cu alloys
  47. Experimental and theoretical characterization of Al3Sc precipitates in Al–Mg–Si–Cu–Sc–Zr alloys
  48. Ag2Al plates in Al–Ag alloys
  49. A critical analysis of the composite model as applied to high-temperature creep of Al and an Al–Mg alloy
  50. Damage behaviour of an Al2O3 particle-reinforced 6061 alloy induced by monotonic and cyclic deformation
  51. Deformation behaviour of ultrafine-grained magnesium with 3 vol.% graphite
  52. Notifications/Mitteilungen
  53. Press/Presse
  54. Conferences/Konferenzen
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2025 De Gruyter Brill
Downloaded on 17.9.2025 from https://www.degruyterbrill.com/document/doi/10.1515/ijmr-2006-0048/html
Scroll to top button