Startseite Application of screen-printed carbon electrode modified with lead in stripping analysis of Cd(II)
Artikel Open Access

Application of screen-printed carbon electrode modified with lead in stripping analysis of Cd(II)

  • Katarzyna Tyszczuk-Rotko EMAIL logo , Katarzyna Domańska , Karel Vytřas , Radovan Metelka , Agnieszka Nosal-Wiercińska und Milan Sýs
Veröffentlicht/Copyright: 1. März 2017
Artikel downloaden (PDF)
Open Chemistry
Aus der Zeitschrift Open Chemistry Band 15 Heft 1

Abstract

In the work presented, a lead film electrode was prepared in situ on a screen-printed carbon support using a reversibly deposited mediator (Zn) and applied to the determination of Cd(II) by anodic stripping voltammetry. The electrochemical method for lead film formation is based on a co-deposition of a metal of interest (Pb), with a reversibly deposited zinc mediator, followed by oxidation of zinc, with additional deposition of lead at the appropriate potential. It serves to increase the density of lead particles, promoting lead film growth, and consequently helps to improve the electrochemical properties of the electrode. This was confirmed by microscopic and voltammetric studies. The obtained detection limit of Cd(II) is equal to 6.6 × 10−9 mol L−1 (−1.6 V for 180 s and then −0.95 V for 5 s). The presented procedure was successfully applied to cadmium determination in Bystrzyca River water samples.

Keywords: striping voltammetry; cadmium determination; screen-printed lead film electrode; zinc mediator

1 Introduction

Stripping analysis is considered to be the most sensitive electroanalytical technique and highly suitable for the task of field monitoring of toxic metals. The sensitivity of stripping analysis is attributed to its preconcentration step, in which trace metals are accumulated onto the working electrode surface [1,2]. A great variety of electrodes have been employed in metal determination, but screen-printed electrodes (SPEs) have low unit costs and are capable of undergoing mass production while still maintaining adequate levels of reproducibility. Moreover, SPEs have the advantage of miniaturization. SPEs have been developed as single-use sensors for a variety of applications in environmental, industrial and clinical analyses [3,4]. Among numerous variants of SPEs, screen-printed carbon electrodes (SPCEs) have attracted a great deal of attention because of their easy-to-make modifications, either by immobilizing a modifier on the electrode surface or adding it to the carbon ink before the electrode is made.

Cadmium is a heavy metal which is extremely toxic to animals. Although the mechanisms of cadmium toxicity are poorly understood, it has been speculated that cadmium causes single-strand DNA damage and disrupts the synthesis of nucleic acids and proteins [5]. Cadmium ions are relatively soluble in water and are readily absorbed in plant tissues and in animal organs such as the liver and kidneys. Many kinds of screen-printed electrodes have been used as electrochemical sensors of Cd(II), however, the most common in the literature are: mercury-coated SPEs [6-10], bismuth-coated SPEs [11-17], gold SPEs and gold and/or carbon nanostructured SPEs [18,19]. In the case of voltammetric procedures of Cd(II) determination employing screen-painted electrodes, the lowest detection limit of 8.9 × 10−10 mol L−1 (for a preconcentration time of 360 s) was obtained using sputtered Bi SPE [17].

In 2005 the lead film electrode (PbFE) was introduced for the first time for adsorptive stripping voltammetric determinations of inorganic ions such as Co(II) and Ni(II) [20]. This electrode has several attractive properties that include simple preparation, good reproducibility and electrochemical surface renewal, mechanical stability, ability to operate in a wide range of media with varying pH, effective preconcentration in stripping procedures, well-defined and separated stripping signals for several metal ions and organic compounds [20-23].

In the present article, we report the first utilization of screen-printed carbon electrode as the support for an in situ plated lead film electrode prepared with the use of a reversibly deposited mediator [24]. In this approach, a metal of interest (Pb) is co-deposited with a mediator (Zn), followed by the subsequent oxidation of zinc and further deposition of lead at the appropriate potential. The investigated electrode was tested as a sensor for the anodic stripping voltammetric determination of Cd(II) traces. It is worth noting that, to date, our studies have confirmed the usefulness of the mediator for enhancing the electrochemical properties of the PbFE applied to folic acid and Ni(II) determination and the bismuth film electrode for Sn(IV) determination [25-27].

2 Experimental procedures

2.1 Preparation of screen-printed carbon electrodes

The screen-printed carbon electrodes were prepared by screen-printing of commercial carbon ink (C10903D14, Gwent Electronic Materials Ltd., Pontypool, UK) onto the ceramic supports (each 40 × 10 mm). Thick layers of the carbon ink were formed by brushing the ink through an etched stencil (thickness 100 µm, electrode printing area 105 mm2) with the aid of the spatula provided with the screen-printing device (UL 1505 A, Tesla, Czech Republic) onto the ceramic substrates. The printed electrodes were dried at 60 °C for 30 min and then covered with a layer of PVC insulator, leaving a defined rectangular shaped (5 × 3 mm) working area and a similar area on the other side for electrical contact.

2.2 Determination of Cd(II) at the lead film electrode prepared with and without a mediator

The screen-printed carbon electrode was modified by the lead film using an in situ plating method with and without the use of a reversibly deposited zinc mediator. The lead film coating and the voltammetric determinations of cadmium under the optimized conditions were carried out in a solution containing 0.1 mol L−1 acetate buffer (pH 4.6 ± 0.1), 2 × 10−5 mol L−1 Pb(II), 0 or 1 × 10−5 mol L−1 Zn(II) and variable concentrations of Cd(II). The potential of the electrode was changed in the following sequence: 0.5 V for 30 s, −1.6 V for 180 s and −0.95 V for 5 s. The first step (the potential of 0.5 V for 30 s), was applied to clean the electrode from the lead remaining after the preceding measurement. In the next step (the potential of −1.6 V for 180 s), Zn, Pb and Cd were deposited simultaneously onto a screen-printed carbon surface. During the third step (the potential of −0.95 V for 5 s), zinc was stripped from the surface, while lead and cadmium continued to be deposited. During both steps the solution was stirred using a magnetic stirring bar. The stirring was stopped and after 5 s equilibration time, the anodic square wave voltammograms were recorded between -1.6 and 0.5 V with frequency of 10 Hz, amplitude of 50 mV and scan rate of 10 mV s−1. The oxidation peak of lead was much larger than that of cadmium, so the recorded voltammograms were cut in the potential range from -1.2 to -0.6 V. Solutions were not deaerated before voltammetry measurements.

2.3 Reagents and water samples

1 mol L-1 acetate buffer (pH = 4.5 ± 0.1), was used as a supporting electrolyte for the proposed voltammetric method and it was prepared from CH3COOH and NaOH obtained from Sigma-Aldrich and Merck, respectively. The stock standard solutions of Pb(II), Zn(II) and Cd(II) (1 g L−1 ) were purchased from Merck. The working solutions of Pb(II), Zn(II) and Cd(II) were prepared by appropriate dilution of the stock standard solutions in 0.1 mol L−1 HNO3 (Merck). All solutions were prepared using ultra-purified water (>18 MΩ cm) supplied by a Milli-Q system (Millipore, UK).

The natural water samples were collected from Bystrzyca River (Lublin, Poland). This material was filtered using a 0.45 µm Millipore filter, acidified to pH = 2 using concentrated HNO3 (Merck) and then UV-irradiated for 3 h.

2.4 Apparatus

The electrochemical experiments were carried out using a µAutolab analyzer (Eco Chemie, Netherlands) in conjunction with a three-electrode system. The electrochemical cell consisted of the silver/silver chloride/ potassium chloride (Ag/AgCl/KCl 3 mol L−1 ) reference electrode, platinum wire as the counter electrode, and the modified screen-printed carbon electrode as the working electrode.

High-resolution microscope FEI DualBeam™ Quanta™ 3D FEG (a/the scanning electron microscope (SEM) with focused ion beam (FIB)) equipped with an energy dispersive X-ray spectrometer (EDS) was used for the electrode surface characterization.

The water samples were mineralized using a UV-digester made by Mineral (based in Poland).

3 Results and Discussion

3.1 Comparison of electrodes

In order to improve the sensitivity of Cd(II) determination at an in situ plated screen-printed lead film electrode a reversibly deposited mediator was applied. Such an application of a mediator in the lead film electrode preparatory step was recently described for the determination of folic acid and Ni(II) [25,26]. This experimental work confirmed that employing a mediator during lead film formation brings about changes in the structure of the lead film and increases the surface coverage of glassy carbon by lead particles. Since this practice facilitated the adsorption of folic acid or the Ni(II) complexes with nioxime, and consequently provided a significant enhancement of voltammetric responses, it was decided to apply this technique to Cd(II) determination.

A comparative study of the in situ plated lead film electrodes prepared with and without the use of a zinc mediator for measuring 5 × 10-7 mol L-1 Cd(II) is presented in Fig. 1. Well-defined and sharp cadmium signals were obtained using the two studied electrodes, however, as can be seen from Fig. 1, the use of a zinc mediator caused an increase of the Cd signal and a decrease of the background current. To better illustrate the role of a zinc mediator, the influence of Zn(II) concentration on the peak currents of Cd(II) (5 × 10−7 mol L−1 and 2 × 10−6 mol L−1 ) are presented in Fig. 2. The relative standard deviations of five replicate determinations of Cd(II) for each concentration of Zn(II) were in the range of 3.3 to 4.9%. The Cd(II) peak current increased with increasing the mediator zinc concentration up to 1 × 10−5 mol L−1. Since the peak current of Cd(II) slightly decreased at 5 × 10−5 mol L−1 Zn(II), the Zn(II) concentration of 1 × 10−5 mol L−1 was chosen for subsequent experiments. The microscopic observation (Fig. 3) correlated well with the results of the electrochemical study. The improvement in electrode electrochemical properties with the use of a mediator is connected with the increase of the electrode active surface area, where Cd(II) ions can be reduced to a metallic state. The presence of lead particles on the electrode surface was confirmed using EDS analysis.

Figure 1 Square wave voltammograms obtained at the in situ plated lead film electrode prepared without (a and b) and with (c) the use of a zinc mediator. The solution for electrode preparation and Cd(II) determination contained 0.1 mol L−1 acetate buffer pH = 4.6 ± 0.1, 5 × 10−6 mol L−1 Pb(II), 0 (a) or 5 × 10−7 mol L−1 Cd(II) (b and c) and 0 (a and b) or 1 × 10−5 mol L−1 (c) Zn(II). Zn, Pb and Cd were deposited at −1.5 V for 120 s. The potential and time of zinc oxidation and further deposition of lead and cadmium were −0.95 V and 120 s, respectively.
Figure 1

Square wave voltammograms obtained at the in situ plated lead film electrode prepared without (a and b) and with (c) the use of a zinc mediator. The solution for electrode preparation and Cd(II) determination contained 0.1 mol L−1 acetate buffer pH = 4.6 ± 0.1, 5 × 10−6 mol L−1 Pb(II), 0 (a) or 5 × 10−7 mol L−1 Cd(II) (b and c) and 0 (a and b) or 1 × 10−5 mol L−1 (c) Zn(II). Zn, Pb and Cd were deposited at −1.5 V for 120 s. The potential and time of zinc oxidation and further deposition of lead and cadmium were −0.95 V and 120 s, respectively.

Figure 2 Influence of Zn(II) concentration on the voltammetric signal of Cd(II). The solution contained 0.1 mol L−1 acetate buffer pH = 4.6 ± 0.1, 5 × 10−6 mol L−1 Pb(II), 5 × 10−7 mol L−1 (a) or 2 × 10−6 mol L−1 Cd(II) (b) and increasing concentration of Zn(II). Other parameters were as in Fig. 1.
Figure 2

Influence of Zn(II) concentration on the voltammetric signal of Cd(II). The solution contained 0.1 mol L−1 acetate buffer pH = 4.6 ± 0.1, 5 × 10−6 mol L−1 Pb(II), 5 × 10−7 mol L−1 (a) or 2 × 10−6 mol L−1 Cd(II) (b) and increasing concentration of Zn(II). Other parameters were as in Fig. 1.

Figure 3 SEM images of lead film electrode surface prepared without (A) and with (B) the use of a zinc mediator. The solution for electrode preparation contained 0.1 mol L−1 acetate buffer pH = 4.6 ± 0.1, 2 × 10−5 mol L−1 Pb(II) and 0 (A) or 1 × 10−5 mol L−1 (B) Zn(II). Zn and Pb were deposited at −1.6 V for 180 s. The potential and time of zinc oxidation and further deposition of lead were −0.95 V and 5 s, respectively. The EDS spectrum of highlighted fragment of the lead film electrode surface prepared with the mediator (C).
Figure 3

SEM images of lead film electrode surface prepared without (A) and with (B) the use of a zinc mediator. The solution for electrode preparation contained 0.1 mol L−1 acetate buffer pH = 4.6 ± 0.1, 2 × 10−5 mol L−1 Pb(II) and 0 (A) or 1 × 10−5 mol L−1 (B) Zn(II). Zn and Pb were deposited at −1.6 V for 180 s. The potential and time of zinc oxidation and further deposition of lead were −0.95 V and 5 s, respectively. The EDS spectrum of highlighted fragment of the lead film electrode surface prepared with the mediator (C).

3.2 Optimization of voltammetric procedure, calibration graph and analytical application

The influence of different voltammetric conditions and parameters on the peak height of 5 × 10−7 mol L−1 Cd(II) was investigated. The obtained results are presented in Fig. 4 and Table 1, and they were used for calibration graph construction (Fig. 5). The Cd(II) oxidation peak current attained a maximum and stable value as lead, zinc and cadmium were simultaneously deposited for 1200 s. However, for further measurements a time of 180 s was chosen in order to decrease the total time of analysis. Additionally, in order to decrease the total time of analysis the scan rate of 10 mV s−1 was chosen for subsequent experiments. It was found that the calibration graph was linear from 5 × 10−8 to 5 × 10−6 mol L−1 and obeyed the equation y = 6.25 x + 0.41, where y is the peak current (µA) and x is the Cd(II) concentration (µmol L−1). The correlation coefficient (r) was 0.9983. The detection and quantification limits of Cd(II) estimated at 3 and 10 times the standard deviation (n = 5) for the lowest determined concentration divided by the slope of the linear regression equation are equal to 6.6 × 10−9 mol L−1 and 2.3 × 10−8 mol L−1 (a total deposition time of 185 s), respectively. The detection limit of the presented procedure is lower than those obtained at the bismuth film screen-printed electrodes [28].

Figure 4 Influence of: A) time of Zn oxidation, B) Pb(II) concentration, C) deposition potential, D) deposition time, E) frequency, F) amplitude, G) scan rate on the voltammetric signal of 5 × 10−7 mol L−1 Cd(II) (A-G, line a) and on the voltammetric signal of 1 × 10−5 mol L−1 Zn(II) (A, line b).
Figure 4

Influence of: A) time of Zn oxidation, B) Pb(II) concentration, C) deposition potential, D) deposition time, E) frequency, F) amplitude, G) scan rate on the voltammetric signal of 5 × 10−7 mol L−1 Cd(II) (A-G, line a) and on the voltammetric signal of 1 × 10−5 mol L−1 Zn(II) (A, line b).

Table 1

Optimized voltammetric conditions and parameters for Cd(II) determination at the lead film screen-printed carbon electrode prepared with the use of a zinc mediator.

Conditions and parametersStudied rangeChosen value
Zn(II) concentration0.5 - 100 µmol L−110 µmol L−1
Time of Zn oxidation0 – 120 s5 s
Pb(II) concentration0.2 - 100 µmol L−120 µmol L−1
Deposition potential−1.65 – (−0.95) V−1.6 V
of Zn, Pb, Cd
Deposition time0 – 1200 s180 s
of Zn, Pb, Cd
Frequency8 – 100 Hz10 Hz
Amplitude10 – 100 mV50 mV
Scan rate2 – 50 mV s−110 mV s−1

Figure 5 Calibration curve of Cd(II). The solution for electrode preparation contained 0.1 mol L−1 acetate buffer pH = 4.6 ± 0.1, 2 × 10−5 mol L−1 Pb(II), 1 × 10−5 mol L−1 Zn(II) and increasing concentration of Cd(II). Zn, Pb and Cd were deposited at −1.6 V for 180 s. The potential and time of zinc oxidation and further deposition of lead and cadmium were -0.95 V and 5 s, respectively.
Figure 5

Calibration curve of Cd(II). The solution for electrode preparation contained 0.1 mol L−1 acetate buffer pH = 4.6 ± 0.1, 2 × 10−5 mol L−1 Pb(II), 1 × 10−5 mol L−1 Zn(II) and increasing concentration of Cd(II). Zn, Pb and Cd were deposited at −1.6 V for 180 s. The potential and time of zinc oxidation and further deposition of lead and cadmium were -0.95 V and 5 s, respectively.

The Cd(II) concentration in the Bystrzyca River samples was below the detection limit of the procedure at the in situ plated lead film screen-printed carbon electrode prepared with a mediator. The analyzed samples were therefore spiked with Cd(II) at concentration levels of 5 × 10−8 and 2 × 10−7 mol L−1 and then the cadmium content was determined using the standard addition method. The recovery values are 102.8% and 99.0% with relative standard deviations of 4.2% and 3.9%, respectively. The obtained results (Table 2) showed satisfactory accuracy and precision of the proposed voltammetric procedure.

Table 2

Results of Cd(II) determination at an in situ plated lead film scree-printed carbon electrode in Bystrzyca River samples.

SampleCd(II) added (mol L−1)Cd(II) found (mol L−1)Recovery (%)RSD (n = 5) (%)
Bystrzyca00--
River5.0 × 10−85.14 × 10−8102.84.2
2.0 × 10−71.98 × 10−799.03.9

4 Conclusions

The obtained results show that the in situ plated lead film screen-printed carbon electrode prepared with the use of a reversibly deposited zinc mediator provides a much better electrochemical performance in comparison to the lead film electrode prepared without a mediator. The data confirm the fact that the morphology of lead film significantly influences the active surface area of these electrodes, thus facilitating the deposition of cadmium and providing a significant enhancement of the voltammetric response.

Acknowledgement

The project was financed from the resources of the Polish National Science Centre, and was awarded on the basis of decision No. DEC-2013/08/M/ ST4/00286.

References

[1] Wang J., Analytical electrochemistry, VCH, USA, 1995, pp. 44-49.Suche in Google Scholar

[2] Bard A.J., Faulkner L.R., Electrochemical methods: fundamentals and application, 2nd ed., Wiley, New York, 2001, pp. 459-462.Suche in Google Scholar

[3] Honeychurch K.C., Hart J.P., Screen-printed electrochemical sensors for monitoring metal pollutants, TrAC Trend. Anal. Chem., 2003, 22, 456-469.10.1016/S0165-9936(03)00703-9Suche in Google Scholar

[4] Stozhko N.Y., Malakhova N.A., Fyodorov M.V., Brainina K.Z., Modified carbon-containing electrodes in stripping voltammetry of metals. Part II. Composite and microelectrodes, J. Solid State Electrochem., 2008, 12, 1219-1230.10.1007/s10008-007-0472-4Suche in Google Scholar

[5] Tchounwou P.B., Yedjou C.G., Patlolla A.K., Sutton D. J., Heavy metal toxicity and the environment, Mol. Clin. Environ. Toxicol., 2012, 101, 133-164.10.1007/978-3-7643-8340-4_6Suche in Google Scholar PubMed PubMed Central

[6] Palchietti I., Cagnini A., Mascini M., Turner A.P.F., Characterization of screen-printed electrodes for detection of heavy metals, Microchim. Acta, 1999, 131, 65-73.10.1007/s006040050010Suche in Google Scholar

[7] Palchetti I., Laschi S., Mascini M., Miniaturised stripping based carbon modified sensor for in field analysis of heavy metals, Anal. Chim. Acta, 2005, 530, 61-67.10.1016/j.aca.2004.08.065Suche in Google Scholar

[8] Ribeiro L.F., Masini J.C., Automated determination of Cu(II), Pb(II), Cd(II) and Zn(II) in environmental samples by square wave voltammetry exploiting sequential injection analysis and screen printed electrodes, Electroanal., 2014, 26, 2754-2763.10.1002/elan.201400462Suche in Google Scholar

[9] Parat C., Betelu S., Authier L., Potin-Gautier M., Determination of labile trace metals with screen-printed electrode modified by a crown-ether based membrane, Anal. Chim. Acta, 2006, 573-574, 14-19.10.1016/j.aca.2006.04.081Suche in Google Scholar PubMed

[10] Song W., Zhang L, Shil L.D.W., Li Y., Long Y.T., Simultaneous determination of cadmium(II), lead(II) and copper(II) by using a screen-printed electrode modified with mercury nano-droplets, Microchim. Acta, 2010, 169, 321-326.10.1007/s00604-010-0354-9Suche in Google Scholar

[11] Rico M.A.G., Olivares-Marín M., Gil E.P., A novel cell design for the improved stripping voltammetric detection of Zn(II), Cd(II), and Pb(II) on commercial screen-printed strips by bismuth codeposition in stirred solutions, Electroanal., 2008, 20, 2608-2613.10.1002/elan.200804360Suche in Google Scholar

[12] Serrano N., Díaz-Cruz J.M., Ariño C., Esteban M., Ex situ deposited bismuth film on screen-printed carbon electrode: a disposable device for stripping voltammetry of heavy metal ions, Electroanal., 2010, 22, 1460-1467.10.1002/elan.200900183Suche in Google Scholar

[13] Kadara R.O., Tothill I.E., Development of disposable bulk-modified screen-printed electrode based on bismuth oxide for stripping chronopotentiometric analysis of lead(II) and cadmium(II) in soil and water samples, Anal. Chim. Acta, 2008, 623, 76-81.10.1016/j.aca.2008.06.010Suche in Google Scholar PubMed

[14] Kadara R.O., Jenkinson N., Banks C.E., Disposable bismuth oxide screen printed electrodes for the high throughput screening of heavy metals, Electroanal., 2009, 21, 2410-2414.10.1002/elan.200900266Suche in Google Scholar

[15] Hwang G.H., Han W.K., Park J.S., Kang S.G., An electrochemical sensor based on the reduction of screen-printed bismuth oxide for the determination of trace lead and cadmium, Sensor. Actuat. B: Chem, 2008, 135, 309-316.10.1016/j.snb.2008.08.039Suche in Google Scholar

[16] Rico M.A.G., Olivares-Marin M., Gil E.P., Modification of carbon screen-printed electrodes by adsorption of chemically synthesized Bi nanoparticles for the voltammetric stripping detection of Zn(II), Cd(II) and Pb(II), Talanta, 2009, 80, 631-635.10.1016/j.talanta.2009.07.039Suche in Google Scholar PubMed

[17] Sosa V., Serrano N., Ariño C., Díaz-Cruz J.M., Esteban M., Sputtered bismuth screen-printed electrode: a promising alternative to other bismuth modifications in the voltammetric determination of Cd(II) and Pb(II) ions in groundwater, Talanta, 2014, 119, 348-352.10.1016/j.talanta.2013.11.032Suche in Google Scholar PubMed

[18] Laschi S., Palchetti I., Mascini M., Gold-based screen-printed sensor for detection of trace lead, Sensor. Actuat. B: Chem., 2006, 114, 460-465.10.1016/j.snb.2005.05.028Suche in Google Scholar

[19] Feng W., Hong-Wei L., Xin Y., Di-Zhao C., GS-nafion-Au nanocomposite film modified SPCEs for simultaneous determination of trace Pb2+ and Cd2+ by DPSV, Int. J. Electrochem. Sci., 2013, 8, 7702-7712.Suche in Google Scholar

[20] Korolczuk M., Tyszczuk K., Grabarczyk M., Adsorptive stripping voltammetry of nickel and cobalt at in situ plated lead film electrode, Electrochem. Commun., 2005, 7, 1185-1189.10.1016/j.elecom.2005.08.022Suche in Google Scholar

[21] Tyszczuk K., Korolczuk M., Analysis of organic compounds using an in situ plated lead film electrode, Com. Chem. High T. Scr., 2010, 13, 753-757.10.2174/138620710791920365Suche in Google Scholar PubMed

[22] Wasąg J., Grabarczyk M., A fast and simple voltammetric method using a lead film electrode for determination of ultra-trace concentration of titanium in environmental water samples, J. Electrochem. Soc., 2016, 163, H1076-H1080.10.1149/2.0981613jesSuche in Google Scholar

[23] Tyszczuk-Rotko K., Rotko M., Voltammetric determination of platinum at a lead film electrode in environmental water samples, Environ. Monit. Assess. 2014, 186, 7801-7806.10.1007/s10661-014-3968-2Suche in Google Scholar PubMed

[24] Sieradzki K., Brankovic S.R., Dimitrov N., Electrochemical defect-mediated thin-film growth., Science, 1999, 284, 138-141.10.1126/science.284.5411.138Suche in Google Scholar PubMed

[25] Tyszczuk K., The fabrication and characterization of an ex situ plated lead film electrode prepared with the use of a reversibly deposited mediator metal, Electrochim. Acta, 2011, 56, 3975-3980.10.1016/j.electacta.2011.02.015Suche in Google Scholar

[26] Tyszczuk-Rotko K., Metelka R., Vytřas K., Barczak M., Lead film electrode prepared with the use of a reversibly deposited mediator metal in adsorptive stripping voltammetry of nickel, Electroanal., 2014, 26, 2049-2056.10.1002/elan.201400263Suche in Google Scholar

[27] Tyszczuk-Rotko K., Metelka R., Vytřas K., Barczak M., Sadok I., Mirosław B., A simple and easy way to enhance sensitivity of Sn(IV) on bismuth film electrodes with the use of a mediator, Monatsh. Chem., 2016, 47, 61-68.10.1007/s00706-015-1601-xSuche in Google Scholar

[28] Barton J., García M.B.G., Santos D.H., Fanjul-Bolado P., Ribotti A., McCaul M., Diamond D., Magni P., Screen-printed electrodes for environmental monitoring of heavy metal ions: a review, Microchim. Acta, 2016, 183, 503-517.10.1007/s00604-015-1651-0Suche in Google Scholar

Received: 2016-11-15
Accepted: 2017-1-25
Published Online: 2017-3-1

© 2017 Katarzyna Tyszczuk-Rotko et al.

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

Artikel in diesem Heft

  1. Regular Articles
  2. Rare Coumarins Induce Apoptosis, G1 Cell Block and Reduce RNA Content in HL60 Cells
  3. Regular Articles
  4. Evaluation of the photocatalytic ability of a sol-gel-derived MgO-ZrO2 oxide material
  5. Regular Articles
  6. Extraction Methods for the Isolation of Isoflavonoids from Plant Material
  7. Regular Articles
  8. Micro and nanocomposites of polybutadienebased polyurethane liners with mineral fillers and nanoclay: thermal and mechanical properties
  9. Regular Articles
  10. Effect of pH on Structural, Magnetic and FMR Properties of Hydrothermally Prepared Nano Ni Ferrite
  11. Regular Articles
  12. Statistical approach to study of lithium magnesium metaborate glasses
  13. Regular Articles
  14. The effectiveness of biodrying waste treatment in full scale reactor
  15. Regular Articles
  16. Chemical comparison of the underground parts of Valeriana officinalis and Valeriana turkestanica from Poland and Kazakhstan
  17. Regular Articles
  18. Phytochemical Characterization and Biological Evaluation of the Aqueous and Supercritical Fluid Extracts from Salvia sclareoides Brot
  19. Regular Articles
  20. Recent Microextraction Techniques for Determination and Chemical Speciation of Selenium
  21. Regular Articles
  22. Compost leachate treatment using polyaluminium chloride and nanofiltration
  23. Regular Articles
  24. Facile and Effective Synthesis of Praseodymium Tungstate Nanoparticles through an Optimized Procedure and Investigation of Photocatalytic Activity
  25. Regular Articles
  26. Computational Study on Non-linear Optical and Absorption Properties of Benzothiazole based Dyes: Tunable Electron-Withdrawing Strength and Reverse Polarity
  27. Regular Articles
  28. Comparative sorption studies of chromate by nano-and-micro sized Fe2O3 particles
  29. Regular Articles
  30. Recycling Monoethylene Glycol (MEG) from the Recirculating Waste of an Ethylene Oxide Unit
  31. Regular Articles
  32. Antimicrobial activity and thiosulfinates profile of a formulation based on Allium cepa L. extract
  33. Regular Articles
  34. The effect of catalyst precursors and conditions of preparing Pt and Pd-Pt catalysts on their activity in the oxidation of hexane
  35. Regular Articles
  36. Platinum and vanadate Bioactive Complexes of Glycoside Naringin and Phenolates
  37. Regular Articles
  38. Antimicrobial sesquiterpenoids from Laurencia obtusa Lamouroux
  39. Regular Articles
  40. Comprehensive spectroscopic (FT-IR, FT-Raman, 1H and 13C NMR) identification and computational studies on 1-acetyl-1H-indole-2,3-dione
  41. Regular Articles
  42. A combined experimental and theoretical study on vibrational and electronic properties of (5-methoxy-1H-indol-1-yl)(5-methoxy-1H-indol-2-yl)methanone
  43. Regular Articles
  44. Erratum to: Analysis of oligonucleotides by liquid chromatography with alkylamide stationary phase
  45. Regular Articles
  46. Non-isothermal Crystallization, Thermal Stability, and Mechanical Performance of Poly(L-lactic acid)/Barium Phenylphosphonate Systems
  47. Regular Articles
  48. Vortex assisted-supramolecular solvent based microextraction coupled with spectrophotometric determination of triclosan in environmental water samples
  49. Regular Articles
  50. Investigation on Two Compounds of O,O’-dithiophosphate Derivatives as Corrosion Inhibitors for Q235 Steel in Hydrochloric Acid Solution
  51. Regular Articles
  52. Evaluation of temporary seasonal variation of heavy metals and their potential ecological risk in Nzhelele River, South Africa
  53. Regular Articles
  54. Synthesis, characterization, second and third order non-linear optical properties and luminescence properties of 1,10-phenanthroline-2,9-di(carboxaldehyde phenylhydrazone) and its transition metal complexes
  55. Regular Articles
  56. Spectrodensitometric simultaneous determination of esomeprazole and domperidone in human plasma
  57. Regular Articles
  58. Computer-aided drug design of capuramycin analogues as anti-tuberculosis antibiotics by 3D-QSAR and molecular docking
  59. Regular Articles
  60. Synthesis, characterization, thermal degradation and urease inhibitory studies of the new hydrazide based Schiff base ligand 2-(2-hydroxyphenyl)-3-{[(E)-(2-hydroxyphenyl)methylidene]amino}-2,3-dihydroquinazolin-4(1H)-one
  61. Regular Articles
  62. Quaternary salts derived from 3-substituted quinuclidine as potential antioxidative and antimicrobial agents
  63. Regular Articles
  64. Bio-concentration of Polycyclic Aromatic Hydrocarbons in the grey Mangrove (Avicennia marina) along eastern coast of the Red Sea
  65. Regular Articles
  66. Quantitative Investigation of Roasting-magnetic Separation for Hematite Oolitic-ores: Mechanisms and Industrial Application
  67. Regular Articles
  68. Photobleaching characteristics of α-(8-quinolinoxy) zinc phthalocyanine, a new type of amphipathic complex
  69. Regular Articles
  70. Methane dry reforming over Ni catalysts supported on Ce–Zr oxides prepared by a route involving supercritical fluids
  71. Regular Articles
  72. Thermodynamic Compatibility, Crystallizability, Thermal, Mechanical Properties and Oil Resistance Characteristics of Nanostructure Poly (ethylene-co-methyl acrylate)/Poly(acrylonitrile-co-butadiene) Blends
  73. Regular Articles
  74. The crystal structure of compositionally homogeneous mixed ceria-zirconia oxides by high resolution X-ray and neutron diffraction methods
  75. Topical Issue on Agriculture
  76. Properties of the filtrate from treatment of pig manure by filtration method
  77. Topical Issue on Agriculture
  78. Monitoring content of cadmium, calcium, copper, iron, lead, magnesium and manganese in tea leaves by electrothermal and flame atomizer atomic absorption spectrometry
  79. Topical Issue on Catalysis
  80. Application of screen-printed carbon electrode modified with lead in stripping analysis of Cd(II)
  81. Topical Issue on Research for Natural Bioactive Products
  82. Burdock (Arctium lappa) Leaf Extracts Increase the In Vitro Antimicrobial Efficacy of Common Antibiotics on Gram-positive and Gram-negative Bacteria
  83. Topical Issue on Research for Natural Bioactive Products
  84. A survey of bacterial, fungal and plant metabolites against Aedes aegypti (Diptera: Culicidae), the vector of yellow and dengue fevers and Zika virus
  85. Topical Issue on Research for Natural Bioactive Products
  86. ‘Capiture’ plants with interesting biological activities: a case to go
  87. Topical Issue on Research for Natural Bioactive Products
  88. Volatile terpenoids as potential drug leads in Alzheimer’s disease
  89. Topical Issue on Research for Natural Bioactive Products
  90. Essential Oils as Immunomodulators: Some Examples
  91. Topical Issue on Research for Natural Bioactive Products
  92. Phenolic profiling and therapeutic potential of local flora of Azad Kashmir; In vitro enzyme inhibition and antioxidant
  93. Topical Issue on Research for Natural Bioactive Products
  94. Chemical profile, antioxidant activity and cytotoxic effect of extract from leaves of Erythrochiton brasiliensis Nees & Mart. from different regions of Europe
https://doi.org/10.1515/chem-2017-0004
Schlagwörter für diesen Artikel
striping voltammetry; cadmium determination; screen-printed lead film electrode; zinc mediator
Creative Commons
BY-NC-ND 3.0

Artikel in diesem Heft

  1. Regular Articles
  2. Rare Coumarins Induce Apoptosis, G1 Cell Block and Reduce RNA Content in HL60 Cells
  3. Regular Articles
  4. Evaluation of the photocatalytic ability of a sol-gel-derived MgO-ZrO2 oxide material
  5. Regular Articles
  6. Extraction Methods for the Isolation of Isoflavonoids from Plant Material
  7. Regular Articles
  8. Micro and nanocomposites of polybutadienebased polyurethane liners with mineral fillers and nanoclay: thermal and mechanical properties
  9. Regular Articles
  10. Effect of pH on Structural, Magnetic and FMR Properties of Hydrothermally Prepared Nano Ni Ferrite
  11. Regular Articles
  12. Statistical approach to study of lithium magnesium metaborate glasses
  13. Regular Articles
  14. The effectiveness of biodrying waste treatment in full scale reactor
  15. Regular Articles
  16. Chemical comparison of the underground parts of Valeriana officinalis and Valeriana turkestanica from Poland and Kazakhstan
  17. Regular Articles
  18. Phytochemical Characterization and Biological Evaluation of the Aqueous and Supercritical Fluid Extracts from Salvia sclareoides Brot
  19. Regular Articles
  20. Recent Microextraction Techniques for Determination and Chemical Speciation of Selenium
  21. Regular Articles
  22. Compost leachate treatment using polyaluminium chloride and nanofiltration
  23. Regular Articles
  24. Facile and Effective Synthesis of Praseodymium Tungstate Nanoparticles through an Optimized Procedure and Investigation of Photocatalytic Activity
  25. Regular Articles
  26. Computational Study on Non-linear Optical and Absorption Properties of Benzothiazole based Dyes: Tunable Electron-Withdrawing Strength and Reverse Polarity
  27. Regular Articles
  28. Comparative sorption studies of chromate by nano-and-micro sized Fe2O3 particles
  29. Regular Articles
  30. Recycling Monoethylene Glycol (MEG) from the Recirculating Waste of an Ethylene Oxide Unit
  31. Regular Articles
  32. Antimicrobial activity and thiosulfinates profile of a formulation based on Allium cepa L. extract
  33. Regular Articles
  34. The effect of catalyst precursors and conditions of preparing Pt and Pd-Pt catalysts on their activity in the oxidation of hexane
  35. Regular Articles
  36. Platinum and vanadate Bioactive Complexes of Glycoside Naringin and Phenolates
  37. Regular Articles
  38. Antimicrobial sesquiterpenoids from Laurencia obtusa Lamouroux
  39. Regular Articles
  40. Comprehensive spectroscopic (FT-IR, FT-Raman, 1H and 13C NMR) identification and computational studies on 1-acetyl-1H-indole-2,3-dione
  41. Regular Articles
  42. A combined experimental and theoretical study on vibrational and electronic properties of (5-methoxy-1H-indol-1-yl)(5-methoxy-1H-indol-2-yl)methanone
  43. Regular Articles
  44. Erratum to: Analysis of oligonucleotides by liquid chromatography with alkylamide stationary phase
  45. Regular Articles
  46. Non-isothermal Crystallization, Thermal Stability, and Mechanical Performance of Poly(L-lactic acid)/Barium Phenylphosphonate Systems
  47. Regular Articles
  48. Vortex assisted-supramolecular solvent based microextraction coupled with spectrophotometric determination of triclosan in environmental water samples
  49. Regular Articles
  50. Investigation on Two Compounds of O,O’-dithiophosphate Derivatives as Corrosion Inhibitors for Q235 Steel in Hydrochloric Acid Solution
  51. Regular Articles
  52. Evaluation of temporary seasonal variation of heavy metals and their potential ecological risk in Nzhelele River, South Africa
  53. Regular Articles
  54. Synthesis, characterization, second and third order non-linear optical properties and luminescence properties of 1,10-phenanthroline-2,9-di(carboxaldehyde phenylhydrazone) and its transition metal complexes
  55. Regular Articles
  56. Spectrodensitometric simultaneous determination of esomeprazole and domperidone in human plasma
  57. Regular Articles
  58. Computer-aided drug design of capuramycin analogues as anti-tuberculosis antibiotics by 3D-QSAR and molecular docking
  59. Regular Articles
  60. Synthesis, characterization, thermal degradation and urease inhibitory studies of the new hydrazide based Schiff base ligand 2-(2-hydroxyphenyl)-3-{[(E)-(2-hydroxyphenyl)methylidene]amino}-2,3-dihydroquinazolin-4(1H)-one
  61. Regular Articles
  62. Quaternary salts derived from 3-substituted quinuclidine as potential antioxidative and antimicrobial agents
  63. Regular Articles
  64. Bio-concentration of Polycyclic Aromatic Hydrocarbons in the grey Mangrove (Avicennia marina) along eastern coast of the Red Sea
  65. Regular Articles
  66. Quantitative Investigation of Roasting-magnetic Separation for Hematite Oolitic-ores: Mechanisms and Industrial Application
  67. Regular Articles
  68. Photobleaching characteristics of α-(8-quinolinoxy) zinc phthalocyanine, a new type of amphipathic complex
  69. Regular Articles
  70. Methane dry reforming over Ni catalysts supported on Ce–Zr oxides prepared by a route involving supercritical fluids
  71. Regular Articles
  72. Thermodynamic Compatibility, Crystallizability, Thermal, Mechanical Properties and Oil Resistance Characteristics of Nanostructure Poly (ethylene-co-methyl acrylate)/Poly(acrylonitrile-co-butadiene) Blends
  73. Regular Articles
  74. The crystal structure of compositionally homogeneous mixed ceria-zirconia oxides by high resolution X-ray and neutron diffraction methods
  75. Topical Issue on Agriculture
  76. Properties of the filtrate from treatment of pig manure by filtration method
  77. Topical Issue on Agriculture
  78. Monitoring content of cadmium, calcium, copper, iron, lead, magnesium and manganese in tea leaves by electrothermal and flame atomizer atomic absorption spectrometry
  79. Topical Issue on Catalysis
  80. Application of screen-printed carbon electrode modified with lead in stripping analysis of Cd(II)
  81. Topical Issue on Research for Natural Bioactive Products
  82. Burdock (Arctium lappa) Leaf Extracts Increase the In Vitro Antimicrobial Efficacy of Common Antibiotics on Gram-positive and Gram-negative Bacteria
  83. Topical Issue on Research for Natural Bioactive Products
  84. A survey of bacterial, fungal and plant metabolites against Aedes aegypti (Diptera: Culicidae), the vector of yellow and dengue fevers and Zika virus
  85. Topical Issue on Research for Natural Bioactive Products
  86. ‘Capiture’ plants with interesting biological activities: a case to go
  87. Topical Issue on Research for Natural Bioactive Products
  88. Volatile terpenoids as potential drug leads in Alzheimer’s disease
  89. Topical Issue on Research for Natural Bioactive Products
  90. Essential Oils as Immunomodulators: Some Examples
  91. Topical Issue on Research for Natural Bioactive Products
  92. Phenolic profiling and therapeutic potential of local flora of Azad Kashmir; In vitro enzyme inhibition and antioxidant
  93. Topical Issue on Research for Natural Bioactive Products
  94. Chemical profile, antioxidant activity and cytotoxic effect of extract from leaves of Erythrochiton brasiliensis Nees & Mart. from different regions of Europe
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 25.9.2025 von https://www.degruyterbrill.com/document/doi/10.1515/chem-2017-0004/html
Button zum nach oben scrollen