Detection of failures of adhesively bonded joints using the acoustic emission method
-
Cezary Gozdecki
Abstract
Wooden glued constructions require touch-free monitoring of destructive processes, especially in adhesive bonds that are most exposed to failure. The objective of the investigations was to describe failure processes in the adhesive bond of wood joints, in particular to determine their initiation, propagation, and destruction. The acoustic emission (AE) method was employed as the carrier of information about changes occurring in glued joints, whereas the numerical method was applied to determine values of distribution of tangential stresses generated in adhesive bonds. The acoustic phenomena examined were described using the AE cumulative counts. The authors analysed acoustic signals generated in loaded wooden and plastic overlap samples glued together using polyethyl methacrylate glue as well as in solid samples. On the basis of the acoustic emissions obtained, it was possible to establish characteristic places and stages of escalating structural defects generated from bonds of adhesive joints. This was utilised later on, in conjunction with results of numerical calculations, to determine correlations occurring between the AE cumulative counts and generated tangential stresses. Dependencies established in this way were used to determine characteristic points during the propagation of destructive phenomena of wood adhesive joints. The results obtained proved that it was possible to predict the development of the destruction of wood adhesive joints on the basis of observations of the increasing AE cumulative counts of acoustic signals in combination with tangential stresses determined using the finite elements method.
References
Ansell, M.P. (1982) Acoustic emission from softwood in tension. Wood Sci. Technol.16(1):35–58.10.1007/BF00351373Search in Google Scholar
Apalak, K.M., Davies, R. (1993) Analysis and design of adhesively bonded corner joints. Int. J. Adhesion and Adhesives13(4):219–235.10.1016/0143-7496(93)90025-5Search in Google Scholar
Apalak, K.M., Davies, R. (1994) Analysis and design of adhesively bonded corner joints, fillet effect. Int. J. Adhesion and Adhesives14(3):163–174.10.1016/0143-7496(94)90026-4Search in Google Scholar
Ayarkawa, J., Hirashima, Y., Ando, K., Sasaki, Y. (2001) Monitoring Acoustic Emissions to predict modulus of rapture of finger-joints from tropical African hardwoods. Wood and Fiber Science33(3):450–464.Search in Google Scholar
Baltrushajtis, A.V., Kovalchuk, S.L. (1988) Issledovanije vlijanija eksploatacjonnych faktorov na sostojanije elementov dereviannych kljejenych konstrukcji metodom akustichjeskoj emissii. JVUZ Stroitelstvo Arch.1:131–134.Search in Google Scholar
Bernatowicz, G., Matejak, M. (1995) Schallemission und photogrammetrische Bestimmung der Risslange. Annals of Warsaw Agricultural University SGGW-AR Forestry and Wood Technology46:85–91.Search in Google Scholar
Biblis, E.J., Carino, H.F. (1993) Factors influencing the flexural properties of finger jointed southern pine LVL. Forest Products J.43(1):41–46.Search in Google Scholar
Cyra, G. Acoustic emission monitoring of the wood machining process. The United Graduate School of Agricultural University, Tottori, Ann Arbor, 1997.Search in Google Scholar
Kagawa, Y., Noguchi, M., Katagiri, J. (1980) Detection of acoustic emission in the process of timber drying. Acust. Lett.3(8):150–153.Search in Google Scholar
Kirylov, A.N., Kovalchuk, S.L. (1987) Izuchienie processa zaprasovki i razrushjenija zubchatych sojedinienii metodom akustichieskoj emissii. JVUZ Lesn. Zh.2:59–63.Search in Google Scholar
Kokociński, W., Moliński, W. (1995) Use the acoustic emission method for determination properties of black Oak. Roczniki AR w Poznaniu258(29/30):43–50.Search in Google Scholar
Moliński, W. (1998) Detection of cracks in wood during use acoustic emission method (EA). Rozprawy Naukowe, Zeszyt 288 Roczniki AR w Poznaniu, Poznań.Search in Google Scholar
Moliński, W., Raczkowski, J. (1997) Acoustic emission generated during hygro-mechanical creep of wood being under across to the grain bending. I. The effect of moistening in tension zone of samples. Proc. Int. Conf. COST Action E8 Wood Mechanics “Wood-water relations”. Copenhagen 16–17 June. pp. 1–9.Search in Google Scholar
Moliński, W., Raczkowski, J., Suchorski, P. (1991) Effect of initial moisture content on acoustic emission in wood during its swelling under mechanical restraint. Drevarski Vyskum130:1–9.Search in Google Scholar
Moliński, W., Raczkowski, J., Poliszko, S. (1995) Acoustic activity of wood during across to the grain bending. Folia Forestalia Polonica Ser. B25:65–72.Search in Google Scholar
Nakai, T., Takemura, T. (1995) Torsional properties of tenon joints with ellipsoid-like tensions and mortises. J. Jpn. Wood Res. Soc.41(4): 387–392.Search in Google Scholar
Nakai, T., Takemura, T. (1996) Stress analysis of the through-tenon joint of wood under torsion II. Shear stress analysis of the male using the finite element method. Mokuzai Gakkaishi4:361–368.Search in Google Scholar
Niemz, P., Hänsel, A. (1988) Untersuchungen zur Ermittlung wesentlicher Einflussfaktoren auf die Schallemission von Vollholz und Holzwerkstoffen. Holztechnologie29(2):79–81.Search in Google Scholar
Noguchi, M., Kagawa, Y., Katagiri, J. (1980) Detection of acoustic emission during hardwood drying. Mokuzai Gakkaishi26(9):637–638.Search in Google Scholar
Pellicane, P.J. (1994) Finite element analysis of finger-joints in lumber with dissimilar laminate stiffnesses. Forest Products J.44:17–22.Search in Google Scholar
Porter, A.W., El-Osta, M.L. (1972) Prediction of failure of finger joints using acoustic emissions. Forest Products J.22(9):74–82.Search in Google Scholar
Raczkowski, J., Moliński, W., Poliszko, S. (1995) Use the acoustic emission method to analysis crack growing in the wood. Mat. Sem. “Akustyka w technice, medycynie i kulturze.” Kraków7–9:177–184.Search in Google Scholar
Sato, K., Noguchi, M., Fushitani, M. (1983) The characteristics of acoustic emissions of wood generated during several types of loading. Mokuzai Gakkaishi29(6):409–414.Search in Google Scholar
Smardzewski, J. (1994) Mathematical model and numerical analysis of stresses distribution in rectangular glue line. Badania dla Meblarstwa Wydawnictwo AR Poznań. pp. 31–45.Search in Google Scholar
Smardzewski, J. (1995) Stress distribution in rectangular glue line firniture's joints. Badania dla Meblarstwa Wydawnictwo AR Poznań. pp. 45–55.Search in Google Scholar
Smardzewski, J. (1996) Distribution of stress in finger joints. Wood Science and Technology6:477–489.Search in Google Scholar
Smardzewski, J. (1998a) Influence of wood and glue line heterogeneity on stress distribution in firniture's joints. Rozprawy Naukowe, Zeszyt 282 Rocz. AR w Poznaniu, Poznań.Search in Google Scholar
Smardzewski, J. (1998b) Numerical analysis of furniture constructions. Wood Science and Technology32:273–286.10.1007/BF00702895Search in Google Scholar
Smardzewski, J., Dziȩgielewski, S. (1997) Strength analysis of selected furniture's joints. 11 Konferencja Naukowa WTD SGGW. 18–19 Listopad, Warszawa. pp. 143–150.Search in Google Scholar
Smardzewski, J., Gozdecki, C. (2002) AE phenomena from wood adhesive bonds. Annals of Warsaw Agricultural University, Forestry and Wood Technology I. pp. 269–273.Search in Google Scholar
Suchorski, P. (1997) Cracks propagation in wood structure with use the acoustic emission method. 11 Konferencja Naukowa WTD SGGW., Warszawa 18–19 Listopad. pp. 61–66.Search in Google Scholar
Suzuki, M., Schniewind, A.P. (1987) Relationship between fracture thougness and acoustic emission during cleavage failure in adhesive joints. Wood Science and Technology21(2):121–130.10.1007/BF00376192Search in Google Scholar
Tanaka, C., Nakato, T., Takahashi, A. (1988) A new technique for adeptive control optimization in circular sawing. Adaptive control optimization by acoustic emission signals. Mokuzai Gakkaishi34(9):769–771.Search in Google Scholar
Wilczyński, A. (1988) Analysis of tangential stresses in glue line in wood. Wydawnictwo Uczelniane WSP, Bydgoszcz.Search in Google Scholar
Wilczyński, A. (1990) Stress distribution in glue line symmetrical plate made from wood. Zesz. Prob. Post. Nauk Rol.379:115–136.Search in Google Scholar
©2005 by Walter de Gruyter Berlin New York
Articles in the same Issue
- Obituary
- The role of non-phenolic lignin in chlorate-forming reactions during chlorine dioxide bleaching of softwood kraft pulp
- Study of the oxygen effect on mechanical pulp lignin using an improved lignin isolation method
- Quantitative 1H NMR analysis of alkaline polysulfide solutions
- A comparative study on the degradation of cotton linters induced by carbonate and hydroxyl radicals generated from peroxynitrite
- The carbonate radical as one-electron oxidant of carbohydrates in alkaline media
- Leaf-fiber lignins of Phormium varieties compared bysolid-state 13C NMR spectroscopy
- Antifungal activity of iridoid glycosides from the heartwood of Gmelina arborea
- Antioxidant activity of different components of pine species
- Dislocations in Norway spruce fibres and their effect on properties of pulp and paper
- Isolation and identification of antifungal compounds from Amboyna wood
- Biomechanical pulping of spruce wood chips with Streptomyces cyaneus CECT 3335 and handsheet characterization
- Three-dimensional visualisation of bacterial decay in individual tracheids of Pinus sylvestris
- Mass loss and moisture dynamics of Scots pine (Pinus sylvestris L.) exposed outdoors above ground in Sweden
- The influence of cation and anion structure of new quaternary ammonium salts on adsorption and leaching
- Speciation of arsenic and chromium in the leachate from chromated copper arsenate (CCA) type C treated southern pine (Pinus spp.)
- Metal chelation studies relevant to wood preservation.1. Complexation of propyl gallate with Fe2+
- Comparison of UV and confocal Raman microscopy to measure the melamine–formaldehyde resin content within cell walls of impregnated spruce wood
- Comparison of Pinus taeda L. wood property calibrations based on NIR spectra from the radial-longitudinal and radial-transverse faces of wooden strips
- Detection of failures of adhesively bonded joints using the acoustic emission method
- Effect of cross-sectional change of a board specimen on stress wave velocity determination
- Comments on the experimental methodology for determination of the hygro-mechanical properties of wood
- Properties of chemically and mechanically isolated fibres of spruce (Picea abies [L.] Karst.). Part 1: Structural and chemical characterisation
- Properties of chemically and mechanically isolated fibres of spruce (Picea abies[L.] Karst.). Part 2: Twisting phenomena
Articles in the same Issue
- Obituary
- The role of non-phenolic lignin in chlorate-forming reactions during chlorine dioxide bleaching of softwood kraft pulp
- Study of the oxygen effect on mechanical pulp lignin using an improved lignin isolation method
- Quantitative 1H NMR analysis of alkaline polysulfide solutions
- A comparative study on the degradation of cotton linters induced by carbonate and hydroxyl radicals generated from peroxynitrite
- The carbonate radical as one-electron oxidant of carbohydrates in alkaline media
- Leaf-fiber lignins of Phormium varieties compared bysolid-state 13C NMR spectroscopy
- Antifungal activity of iridoid glycosides from the heartwood of Gmelina arborea
- Antioxidant activity of different components of pine species
- Dislocations in Norway spruce fibres and their effect on properties of pulp and paper
- Isolation and identification of antifungal compounds from Amboyna wood
- Biomechanical pulping of spruce wood chips with Streptomyces cyaneus CECT 3335 and handsheet characterization
- Three-dimensional visualisation of bacterial decay in individual tracheids of Pinus sylvestris
- Mass loss and moisture dynamics of Scots pine (Pinus sylvestris L.) exposed outdoors above ground in Sweden
- The influence of cation and anion structure of new quaternary ammonium salts on adsorption and leaching
- Speciation of arsenic and chromium in the leachate from chromated copper arsenate (CCA) type C treated southern pine (Pinus spp.)
- Metal chelation studies relevant to wood preservation.1. Complexation of propyl gallate with Fe2+
- Comparison of UV and confocal Raman microscopy to measure the melamine–formaldehyde resin content within cell walls of impregnated spruce wood
- Comparison of Pinus taeda L. wood property calibrations based on NIR spectra from the radial-longitudinal and radial-transverse faces of wooden strips
- Detection of failures of adhesively bonded joints using the acoustic emission method
- Effect of cross-sectional change of a board specimen on stress wave velocity determination
- Comments on the experimental methodology for determination of the hygro-mechanical properties of wood
- Properties of chemically and mechanically isolated fibres of spruce (Picea abies [L.] Karst.). Part 1: Structural and chemical characterisation
- Properties of chemically and mechanically isolated fibres of spruce (Picea abies[L.] Karst.). Part 2: Twisting phenomena
