Effect of Compounding Conditions on Mechanical Properties of Glass Fiber-Reinforced Polyamide-6
-
S. Nagae
Abstract
Glass fiber-reinforced polyamide-6 (GFPA-6) was compounded using a HYPERKTX46 twin screw extruder with three different types of screw segments (rotor segments, kneading disc segments and turbine segments). Based on the ‘neural network’ regression analysis, we investigated the effects of compounding conditions, such as screw configurations, screw rotation speed, and production rate on mechanical properties, such as tensile, flexural and impact strength of GFPA-6. It was found that the mechanical properties of GFPA-6 changed in different ways with compounding conditions (screw rotation speed and production rate), depending on the type of screw segments. It was also found that the rotor segment exhibited good mechanical properties in wider ranges of compounding conditions than the kneading disc segment and the turbine segment, probably due to its mild and uniform mixing capability.
© 1997, Carl Hanser Verlag, Munich
Artikel in diesem Heft
- Contents
- Contents
- Editorial
- Third in a Series: Pioneers of Polymer Processing: Charles Goodyear
- Screw Extrusion/Mixing
- Chaotic Features of Flow in Polymer Processing Equipment-Relevance to Distributive Mixing
- Influence of Design on Mixing Efficiency in a Variable Intermeshing Clearance Mixer
- Simulation of Non-Isothermal Flow in a Modular Buss Kneader and Comparison with Experiment
- Rheological Behaviour of LLDPE/LDPE Blends under Elongational Deformation
- Effect of Compounding Conditions on Mechanical Properties of Glass Fiber-Reinforced Polyamide-6
- Die Extrusion
- A New Approach to Simulation of Die Flow which Incorporates the Extruder and Rotating Screw Tips in the Analysis
- New Aspects Concerning the Design of Coathanger Dies
- Film
- On-Line Birefringence Measurement in Film Blowing of a Linear Low Density Polyethylene
- Brittle Melt Rupture Phenomena in Polymer Processing
- Moulding
- Injection Molding of LDPE/BaSO4 Blends
- An Experimental Study of Rotational Molding of Polypropylene/Polyethylene Copolymers
- Determination of the Inter-Relationships Between Processing Conditions and Properties of an Injection Molded Silicone Ring Using an Experimental Design
- Numerical Simulation of the Flow and Fiber Orientation in Reinforced Thermoplastic Injection Molded Products
- Wide-Angle X-Ray, Densitometric and Microscopical Studies on Injection Molded Polypropylene Disks
Artikel in diesem Heft
- Contents
- Contents
- Editorial
- Third in a Series: Pioneers of Polymer Processing: Charles Goodyear
- Screw Extrusion/Mixing
- Chaotic Features of Flow in Polymer Processing Equipment-Relevance to Distributive Mixing
- Influence of Design on Mixing Efficiency in a Variable Intermeshing Clearance Mixer
- Simulation of Non-Isothermal Flow in a Modular Buss Kneader and Comparison with Experiment
- Rheological Behaviour of LLDPE/LDPE Blends under Elongational Deformation
- Effect of Compounding Conditions on Mechanical Properties of Glass Fiber-Reinforced Polyamide-6
- Die Extrusion
- A New Approach to Simulation of Die Flow which Incorporates the Extruder and Rotating Screw Tips in the Analysis
- New Aspects Concerning the Design of Coathanger Dies
- Film
- On-Line Birefringence Measurement in Film Blowing of a Linear Low Density Polyethylene
- Brittle Melt Rupture Phenomena in Polymer Processing
- Moulding
- Injection Molding of LDPE/BaSO4 Blends
- An Experimental Study of Rotational Molding of Polypropylene/Polyethylene Copolymers
- Determination of the Inter-Relationships Between Processing Conditions and Properties of an Injection Molded Silicone Ring Using an Experimental Design
- Numerical Simulation of the Flow and Fiber Orientation in Reinforced Thermoplastic Injection Molded Products
- Wide-Angle X-Ray, Densitometric and Microscopical Studies on Injection Molded Polypropylene Disks
