Volume 39, Issue 5

Powder mixing is a vital operation in a wide range of industries, such as food, pharmaceutical, and cosmetics. Despite the common use of mixing systems in various industries, often due to the complex nature of mixing systems, the effects of operating and design parameters on the mixers’ performance and final blend are not fully known, and therefore optimal parameters are selected through experience or trial and error. Experimental and numerical techniques have been widely used to analyze mixing systems and to gain a detailed understanding of mixing processes. The limitations associated with experimental techniques, however, have made discrete element method (DEM) a valuable complementary tool to obtain comprehensive particle level information about mixing systems. In the present study, the fundamentals of solid-solid mixing, segregation, and characteristics of different types of batch solid mixers are briefly reviewed. Previously published papers related to the application of DEM in studying mixing quality and assessing the influence of operating and design parameters on the mixing performance of various batch mixing systems are summarized in detail. The challenges with regards to the DEM simulation of mixing systems, the available solutions to address those challenges and our recommendations for future simulations of solid mixing are also presented and discussed.

Four interrelated issues have been arising with the development of modern industry, namely environmental pollution, the energy crisis, the greenhouse effect and the global food crisis. Photocatalysis is one of the most promising methods to solve them in the future. To promote high photocatalytic reaction efficiency and utilize solar energy to its fullest, a well-designed photoreactor is vital. Photocatalytic optofluidic microreactors, a promising technology that brings the merits of microfluidics to photocatalysis, offer the advantages of a large surface-to-volume ratio, a short molecular diffusion length and high reaction efficiency, providing a potential method for mitigating the aforementioned crises in the future. Although various photocatalytic optofluidic microreactors have been reported, a comprehensive review of microreactors applied to these four fields is still lacking. In this paper, we review the typical design and development of photocatalytic microreactors in the fields of water purification, water splitting, CO 2 fixation and coenzyme regeneration in the past few years. As the most promising tool for solar energy utilization, we believe that the increasing innovation of photocatalytic optofluidic microreactors will drive rapid development of related fields in the future.

The requirement of running a new generation of fuel production is inevitable due to the limitation of oil production from reservoirs. On the other hand, enhancing the CO 2 concentration in the atmosphere brings global warming phenomenon and leads to catastrophic disasters such as drought and flooding. Conversion of carbon dioxide to methanol can compensate for the liquid fuel requirement and mitigate CO 2 emissions to the atmosphere. In this review, we surveyed the recent works on homogeneous hydrogenation of CO 2 to CH 3 OH and investigated the experimental results in detail. We categorized the CO 2 hydrogenation works based on the environment of the reaction, including neutral, acidic, and basic conditions, and discussed the effects of solvents’ properties on the experimental results. This review provides a perspective on the previous studies in this field, which can assist the researchers in selecting the proper catalyst and solvent for homogenous hydrogenation of carbon dioxide to methanol.

The review focuses on the recent development in anode materials and their synthesis approach, focusing on their compatibility for treating actual industrial wastewater, improving selectivity, electrocatalytic activity, stability at higher concentration, and thereby reducing the mineralization cost for organic pollutant degradation. The advancement in sol–gel technique, including the Pechini method, is discussed in the first section. A separate discussion related to the selection of the electrodeposition method and its deciding parameters is also included. Furthermore, the effect of using advanced heating approaches, including microwave and laser deposition synthesis, is also discussed. Next, a separate discussion is provided on using different types of anode materials and their effect on active •OH radical generation, activity, and electrode stability in direct and indirect oxidation and future aspects. The effect of using different synthesis approaches, additives, and doping is discussed separately for each anode. Graphene, carbon nanotubes (CNTs), and metal doping enhance the number of active sites, electrochemical activity, and mineralization current efficiency (MCE) of the anode. While, microwave or laser heating approaches were proved to be an effective, cheaper, and fast alternative to conventional heating. The electrodeposition and nonaqueous solvent synthesis were convenient and environment-friendly techniques for conductive metallic and polymeric film deposition.

Epoxy resin is commonly used in the oil and gas industry due to its excellent toughness, low shrinkage, good adhesive strength, and relatively good thermal resistance. It is used for water shutoff, zonal isolation, cementing, enhanced oil recovery, and preventing leakage in wells. This paper reviews the chemistry aspect of using an epoxy resin system as a sealant to prevent well leakage and it offers insights into the chemistry of the epoxy resin system, as applied in previous studies. The paper also unveils the reasons for the application of this system from the chemistry perspective, allowing this aspect to be better understood. Success in the investigated cases depended on the formulation design. The epoxide and hydroxyl functional groups have been found to contribute substantially to the excellent performance of the sealant system. Furthermore, the amine curing agent triggers the abrupt reaction of the oxirane ring to stabilise when the cured sealant is perfectly applied. Based on the findings, it is suggested that other types of epoxies, namely epoxidised oils, require further study. Finally, in terms of safety and sustainable energy, it is suggested that more curing agent and diluent studies are undertaken.

This work critically reviews the application of various membrane separation processes (MSPs) in treating water polluted with trace organic compounds (TOrCs) paying attention to nanofiltration (NF), reverse osmosis (RO), membrane bioreactor (MBR), forward osmosis (FO), and membrane distillation (MD). Furthermore, the focus is on loopholes that exist when investigating mechanisms through which membranes reject/retain TOrCs, with the emphasis on the characteristics of the model TOrCs which would facilitate the identification of all the potential mechanisms of rejection. An explanation is also given as to why it is important to investigate rejection using real water samples, especially when aiming for industrial application of membranes with novel materials. MSPs such as NF and RO are prone to fouling which often leads to lower permeate flux and solute rejection, presumably due to cake-enhanced concentration polarisation (CECP) effects. This review demonstrates why CECP effects are not always the reason behind the observed decline in the rejection of TOrCs by fouled membranes. To mitigate for fouling, researchers have often modified the membrane surfaces by incorporating nanoparticles. This review also attempts to explain why nano-engineered membranes have not seen a breakthrough at industrial scale. Finally, insight is provided into the possibility of harnessing solar and wind energy to drive energy intensive MSPs. Focus is also paid into how low-grade energy could be stored and applied to recover diluted draw solutions in FO mode.