Calculation of Average Residence Time in a Ko-kneader
-
B. Vergnes
Abstract
We propose in this short note a rapid and efficient way to calculate the average residence time in a ko-kneader. Two experiments are enough to define the two parameters of the model. The proposed expression has been thoroughly validated by comparison with numerous experimental results obtained in various conditions of screw speed, feed rate and screw profile.
References
Elemans, P. H. M., Meijer, H. E. H., “On the Modelling of Continuous Mixers. Part II: The Co-kneader”, Polym. Eng. Sci., 30, 893–904(1990), DOI: 10.1002/pen.760301504Suche in Google Scholar
Lyu, M. Y., White, J. L., “Models of Flow and Experimental Studies on a Modular List/Buss Kokneter”, Int. Polym. Proc., 10, 305–313(1995)Suche in Google Scholar
Lyu, M. Y., White, J. L., “Modelling of a Viscous Non-Newtonian Polymer Melt in a List/Buss Kneader and Comparison to Experiment”, Int. Polym. Proc., 11, 208–221(1996)Suche in Google Scholar
Lyu, M. Y., White, J. L., “Simulation of Linear Viscoelastic Flow Behaviour in the Buss Kneader”, Polym. Eng. Sci., 3, 623–635(1997a), DOI: 10.1002/pen.11705Suche in Google Scholar
Lyu, M. Y., White, J. L., “Simulation of Non-Isothermal Flow in a Modular Buss Kneader and Comparison with Experiment”, Int. Polym. Proc., 2, 104–109(1997b)10.3139/217.970104Suche in Google Scholar
Lyu, M. Y., White, J. L., “Residence Time Distribution and Basic Studies of Flow and Melting in a Modular Buss Kneader”, Polym. Eng. Sci., 38, 9, 1366–1377(1998), DOI: 10.1002/pen.10307Suche in Google Scholar
Mehrampour, M., et al., “Prediction of Residence Time Distribution in EZ and KE Element of a Ko-kneader by Using CFD Method”, Int. Polym. Proc., 18, 327–329(2003)Suche in Google Scholar
Mehrampour, M., et al., “Prediction of Residence Time Distribution for Different Screw Configurations of a Ko-Kneader By Using a Cluster Model”, Int. Polym. Proc., 19, 13–15(2004)Suche in Google Scholar
Poulesquen, A., Vergnes, B., “A Study of Residence Time Distribution in Co-Rotating Twin Screw Extruders; Part I: Theoretical Modelling”, Polym. Eng. Sci., 43, 1841–1848(2003), DOI: 10.1002/pen.10156Suche in Google Scholar
Stade, K. H., “Techniques for Compounding Glass Fiber-reinforced Thermoplastics”, Polym. Eng. Sci., 17, 50–57(1977), DOI: 10.1002/pen.760170110Suche in Google Scholar
White, J. L.: Twin Screw Extrusion, Technology and Principles, Hanser Publishers, Munich(1990)Suche in Google Scholar
White, J. L., Lyu, M. Y., “Development of the Modern Buss Kneader and the Study of its Flow and Mixing Mechanisms”, Polym.-Plast. Technol. Eng., 37, 3, 385–410(1998), DOI: 10.1080/03602559808006935Suche in Google Scholar
© 2011, Carl Hanser Verlag, Munich
Artikel in diesem Heft
- Contents
- Contents
- Regular Contributed Articles
- Applicability of the Impact Response Analysis Method for Reinforced Concrete Beams Mixed with Polyvinyl Alcohol Short Fibers
- Epoxy-Montmorillonite Nanocomposites Applied to Powder Coatings
- Direct Imprinting Using Magnetic Nickel Mold and Electromagnetism Assisted Pressure for Replication of Microstructures
- Automated Mold Heating System Using High Frequency Induction with Feedback Temperature Control
- The Prediction of Bowing Distortion of Film after Transverse Stretching with Consideration of Heated Air Flow in a Tenter
- The Influence of Injection Molding and Injection Compression Molding on Ultra-high Molecular Weight Polyethylene Polymer Microfabrication
- A Design-of-Experiment Study on the Microcellular Extrusion of Sub-critical CO2 Saturated PLA Pellets
- Optimization of Injection Molding Process for SGF and PTFE Reinforced PC Composites Using Response Surface Methodology and Simulated Annealing Approach
- Flow Visualisation in Co-rotating Twin Screw Extruders: Positron Emission Particle Tracking and Numerical Particle Trajectories
- The Influence of Melt and Process Parameters on the Quality and Occurrence of Part Defects in Water-assisted Injection Molded Tubes
- Model and Numerical Simulation for the Second Penetration in Water-assisted Injection Molding
- Influence of Extrusion Conditions on the Rheological Behavior of Nuclear Bituminized Waste Products
- Influence of Dicumyl Peroxide Content on Thermal and Mechanical Properties of Polylactide
- Rapid Communications
- Calculation of Average Residence Time in a Ko-kneader
- PPS-News
- PPS News
Artikel in diesem Heft
- Contents
- Contents
- Regular Contributed Articles
- Applicability of the Impact Response Analysis Method for Reinforced Concrete Beams Mixed with Polyvinyl Alcohol Short Fibers
- Epoxy-Montmorillonite Nanocomposites Applied to Powder Coatings
- Direct Imprinting Using Magnetic Nickel Mold and Electromagnetism Assisted Pressure for Replication of Microstructures
- Automated Mold Heating System Using High Frequency Induction with Feedback Temperature Control
- The Prediction of Bowing Distortion of Film after Transverse Stretching with Consideration of Heated Air Flow in a Tenter
- The Influence of Injection Molding and Injection Compression Molding on Ultra-high Molecular Weight Polyethylene Polymer Microfabrication
- A Design-of-Experiment Study on the Microcellular Extrusion of Sub-critical CO2 Saturated PLA Pellets
- Optimization of Injection Molding Process for SGF and PTFE Reinforced PC Composites Using Response Surface Methodology and Simulated Annealing Approach
- Flow Visualisation in Co-rotating Twin Screw Extruders: Positron Emission Particle Tracking and Numerical Particle Trajectories
- The Influence of Melt and Process Parameters on the Quality and Occurrence of Part Defects in Water-assisted Injection Molded Tubes
- Model and Numerical Simulation for the Second Penetration in Water-assisted Injection Molding
- Influence of Extrusion Conditions on the Rheological Behavior of Nuclear Bituminized Waste Products
- Influence of Dicumyl Peroxide Content on Thermal and Mechanical Properties of Polylactide
- Rapid Communications
- Calculation of Average Residence Time in a Ko-kneader
- PPS-News
- PPS News
