Home Aging response investigation of 2017 Al alloy processed by gravity and squeeze casting
Article
Licensed
Unlicensed Requires Authentication

Aging response investigation of 2017 Al alloy processed by gravity and squeeze casting

  • Najib Souissi , Catherine Mabru and Chedly Bradai
Published/Copyright: August 22, 2019
Become an author with De Gruyter Brill
Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 110 Issue 9

Abstract

Suitable pressure levels and heat treatment of casting wrought aluminum alloy are key process parameters in making components with better metallurgical properties. For this purpose, the effect of applied pressure and aging treatment on the microstructure and the mechanical properties of an industrial 2017 aluminum alloy manufactured by gravity and direct squeeze casting processes are investigated in this paper. After treating to various aging states, the correlation between these parameters and the characteristics of the cast alloy has been analyzed and discussed.

Keywords: Squeeze pressure; 2017 Al alloy; Aging temperature; Microstructure; Mechanical properties
*Correspondence address, Najib Souissi, Ravago Middle East Company, Industrial city 2 Cross Road 308 & 315, PO BOX 10311, Jubail 35748, Saudi Arabia., Tel.: +966509279529 +21621134957, E-mail: ,

References

[1] B.Lin, W.Zhang, Z.Lou, D.Zhang, Y.Li: Mater. Des.59 (2014) 10. 10.1016/j.matdes.2014.02.012Search in Google Scholar

[2] M.T.Abou El-khair: Mater. Lett.59 (2005) 894. 10.1016/j.matlet.2004.11.041Search in Google Scholar

[3] Z.Han, X.Huang, A.A.Luo, A.K.Sachdev, B.Liu: Scr. Mater.66 (2012) 215. 10.1016/j.scriptamat.2011.10.041Search in Google Scholar

[4] A.Maleki, B.Niroumand, A.Shafyei: Mater. Sci. Eng. A428 (2006) 135. 10.1016/j.msea.2006.04.099Search in Google Scholar

[5] T.M.Yue: J. Mater. Process. Technol.66 (1997) 179. 10.1016/S0924-0136(96)02516-2Search in Google Scholar

[6] S.W.Kim, D.Y.Kim, W.G.Kim, K.D.Woo: Mater. Sci. Eng. A304–306 (2001) 721. 10.1016/S0921-5093(00)01594-XSearch in Google Scholar

[7] S.M.Skolianos, G.Kiourtsidis, T.Xatzifotiou: Mater. Sci. Eng. A231 (1997) 17. 10.1016/S0921-5093(97)00067-1Search in Google Scholar

[8] Z.Ming, Z.Wei-wen, Z.Hai-dong, Z.Da-tong, L.Yuan-yuan: Nonferr. Metal. Soc.17 (2007) 496. 10.1016/S1003-6326(07)60122-8Search in Google Scholar

[9] J.da Costa Teixeira, D.G.Cram, L.Bourgeois, T.J.Bastow, A.J.Hill, C.R.Hutchinson: Acta Mater.56 (2008) 6109. 10.1016/j.actamat.2008.08.023Search in Google Scholar

[10] K.Saï, L.Taleb, G.Cailletaud: Comput. Mater. Sci.65 (2012) 48. 10.1016/j.commatsci.2012.06.035Search in Google Scholar

[11] G.Giuliano: Manuf. Letters.10 (2016) 10. 10.1016/j.mfglet.2016.08.003Search in Google Scholar

[12] N.Souissi, S.Souissi, J.Lecompte, M.B.Amar, C.Bradai, F.Halouani: Int. J. Adv. Manuf. Technol.78 (2015) 2069. 10.1007/s00170-015-6792-0Search in Google Scholar

[13] N.Souissi, S.Souissi, C.L.Niniven, M.B.Amar, C.Bradai, F.Halouani: Metals4 (2014) 141. 10.3390/met4020141Search in Google Scholar

[14] N.Souissi, S.Souissi, C.L.Niniven, M.B.Amar, C.Bradai, F.Halouani: Int. J. Mater. Eng. Innovation6 (2015) 59. 10.1504/IJMATEI.2015.069801Search in Google Scholar

[15] M.B.Amar, S.Souissi, N.Souissi, C.Bradai: Int. J. Microstruct. Mater. Prop.7 (2012) 491. 10.1504/IJMMP.2012.051229Search in Google Scholar

[16] C.Vargel: The most common wrought aluminum alloys. In corrosion of aluminium; Elsevier, Amsterdam, The Netherlands (2004) 65–66. 10.1016/B978-008044495-6/50009-4Search in Google Scholar

[17] Metallic materials and elements for aerospace vehicle structures. Military: Handbook 5H., US Department of Defense, USA (1998).Search in Google Scholar

[18] Y.Birol: Mater. Sci. Eng. A528 (2011) 5636. 10.1016/j.msea.2011.03.101Search in Google Scholar

[19] B.Zlaticanin, B.Radonjic, M.Filipovic: Mater. Sci. Forum453–454 (2004) 193. 10.4028/www.scientific.net/MSF.453-454.193Search in Google Scholar

[20] Y.Birol: J. Mater. Proc. Technol.211 (2011) 1749. 10.1016/j.jmatprotec.2011.05.016Search in Google Scholar

[21] Y.Birol: Mater. Chem. Phys.131 (2012) 694. 10.1016/j.matchemphys.2011.10.036Search in Google Scholar

[22] E.Hajjari, M.Divandari: Mater. Des.29 (2008) 1685. 10.1016/j.matdes.2008.04.012Search in Google Scholar

[23] W.Dai, S.Wu, S.Lü, C.Lin: Mater. Sci. Eng. A538 (2012) 320. 10.1016/j.msea.2012.01.051Search in Google Scholar

Received: 2018-12-24
Accepted: 2019-03-23
Published Online: 2019-08-22
Published in Print: 2019-09-16

© 2019, Carl Hanser Verlag, München

Articles in the same Issue

  1. Original Contributions
  2. Thermodynamic re-assessment of the binary Cr–Ta system down to 0 K
  3. Thermodynamic analysis of precipitation behavior of M23C6 carbide in Nimonic 105 superalloy
  4. Texture evolution of magnesium alloy AZ31 during high temperature tensile deformation
  5. Effect of reciprocating extrusion temperature and passes on the microstructural evolution of Mg-5Sn-1Si-0.8Y alloy
  6. Constitutive modeling of flow behavior of CuZn39Pb2 alloy under hot working conditions
  7. The effect of austempering on the microstructure and mechanical properties of PM Fe-0.8c steel aloyed with copper and nickel
  8. Enhancing the microstructure and grain refining performance of Al-5Ti-1B master alloy by a gas atomization process
  9. Aging response investigation of 2017 Al alloy processed by gravity and squeeze casting
  10. Die-casting aluminum alloys for high-efficiency thermal radiation components
  11. Wear and corrosion of in-situ formed Al3Zr aluminide reinforced Al3003 surface composite
  12. Magnesium aluminate spinel ceramics infiltrated with lanthanum-glass for dental applications
  13. Short Communications
  14. Influence of pre-rolling on microstructural evolution of non-basal textured magnesium alloy
https://doi.org/10.3139/146.111806
Keywords for this article
Squeeze pressure; 2017 Al alloy; Aging temperature; Microstructure; Mechanical properties

Articles in the same Issue

  1. Original Contributions
  2. Thermodynamic re-assessment of the binary Cr–Ta system down to 0 K
  3. Thermodynamic analysis of precipitation behavior of M23C6 carbide in Nimonic 105 superalloy
  4. Texture evolution of magnesium alloy AZ31 during high temperature tensile deformation
  5. Effect of reciprocating extrusion temperature and passes on the microstructural evolution of Mg-5Sn-1Si-0.8Y alloy
  6. Constitutive modeling of flow behavior of CuZn39Pb2 alloy under hot working conditions
  7. The effect of austempering on the microstructure and mechanical properties of PM Fe-0.8c steel aloyed with copper and nickel
  8. Enhancing the microstructure and grain refining performance of Al-5Ti-1B master alloy by a gas atomization process
  9. Aging response investigation of 2017 Al alloy processed by gravity and squeeze casting
  10. Die-casting aluminum alloys for high-efficiency thermal radiation components
  11. Wear and corrosion of in-situ formed Al3Zr aluminide reinforced Al3003 surface composite
  12. Magnesium aluminate spinel ceramics infiltrated with lanthanum-glass for dental applications
  13. Short Communications
  14. Influence of pre-rolling on microstructural evolution of non-basal textured magnesium alloy
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2025 De Gruyter Brill
Downloaded on 12.10.2025 from https://www.degruyterbrill.com/document/doi/10.3139/146.111806/html
Scroll to top button