Startseite Hot torsion behavior of SP-700 near beta titanium alloy in single and dual phase regions
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Hot torsion behavior of SP-700 near beta titanium alloy in single and dual phase regions

  • Amir Hosein Sheikhali , Maryam Morakkabati und Seyed Mahdi Abbasi
Veröffentlicht/Copyright: 29. November 2018
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 109 Heft 12

Abstract

Hot deformation behavior of the SP-700 alloy is studied through continuous and interrupted hot torsion testing carried out at 850 and 1 000 °C at different pass-strains and inter-pass times. The flow curves of SP-700 alloy showed the discontinuous yield stress, which is followed by the steady state region. The dominant mechanism of softening in hot deformation at 1 000 °C was dynamic recrystallization (DRX), whereas at 850 °C serration and tanglement of the grain boundaries were observed. Nevertheless, the microstructure of the sample twisted at 850 °C indicated the occurrence of DRX and the formation of fine grains in the vicinity of grain boundaries and triple points by the bulging mechanism. With an increase in the pass-strain of interrupted torsion at 1 000 °C, due to the increase in driving force for nucleation and growth of new grains, the kinetics of static restoration increased. However, due to the completion of DRX, the kinetics rate of static restoration at steady state strain (∊s) was lower than that of the former state. The β → α phase transformation at 850 °C was found to be another factor contributing in fractional softening.

Keywords: SP-700 titanium alloy; Hot torsion test; Dynamic recrystallization; Fractional softening; Phase transformation
*Correspondence address, Dr Seyed Mahdi Abbasi, No. 15, Qaffar-nazari Alley, Heydary Avenue, Damavand Street, Tehran, Iran, Postal code: 1745953881, Tel.: +982177430446, Fax: +982177430446, E-mail:

References

[1] Military Handbook 5J, Department of Defense Handbook: Metallic materials and elements for aerospace vehicle structures, Wright-Patterson AFB, OH. Materials Directorate (2003) 110.Suche in Google Scholar

[2] M.J.Tan, S.F.Hassan, in: M.Ninomi, S.Akiyama, M.Ikeda, M.Hagiwara, K.Maruyama (Eds.), Ti-2007 Science and Technology, Japan (2007) 567.Suche in Google Scholar

[3] Y.H.Lin, S.M.Wu, F.H.Kao, S.H.Wang, J.R.Yang, C.C.Yang, C.S.Chiou: Mater. Sci. Eng. A528 (2011) 2271. 10.1016/j.msea.2010.12.027Suche in Google Scholar

[4] A.Ogawa, M.Niikura, C.Ouchi, K.Minikawa, M.Yamada: J. Test. Eval.24 (1996) 165.Suche in Google Scholar

[5] B.Gunawarman, M.Niinomi, T.Akahori, J.Takeda, H.Toda: Mater. Sci. Eng. C25 (2005) 296. 10.1016/j.msec.2004.12.012Suche in Google Scholar

[6] J.Nieha, S.L.Lee, K.S.Pan: Int. J. Mater. Res.106 (2015) 1. 10.3139/146.015012Suche in Google Scholar

[7] Gunawarman, M.Niinomi, D.Eylon, S.Fujishiro, C.Ouchi, T.Kazino: Metall. Mater. Trans. A34 (2003) 267. 10.1007/s11661-003-0328-1Suche in Google Scholar

[8] Y.H.Lin, K.H.Hu, F.H.Kao, S.H.Wang, J.R.Yang, C.K.Lin: Mater. Sci. Eng. A528 (2011) 4381. 10.1016/j.msea.2011.02.013Suche in Google Scholar

[9] L.W.Zhu, X.N.Wang, Y.Fei, J.Li, Z.S.Zhu: Mater. Sci. Forum 849, Trans Tech Pub., Switzerland (2016) 309. 10.4028/www.scientific.net/MSF.849.309Suche in Google Scholar

[10] H.Fukai, K.Minakawa, C.Ouchi: ISIJ International44 (2004) 1911. 10.2355/isijinternational.44.1911Suche in Google Scholar

[11] I.Weiss, S.L.Semiatin: Mater. Sci. Eng. A243 (1998) 46. 10.1016/S0921-5093(97)00783-1Suche in Google Scholar

[12] S.L.Semiatin, V.Seetharaman, I.Weiss: JOM (1997) 33. 10.1007/BF02914711Suche in Google Scholar

[13] L.He, A.Dehghan-Manshadi, R.J.Dippenaar: Mater. Sci. Eng.A549 (2012) 163. 10.1016/j.msea.2012.04.025Suche in Google Scholar

[14] P.Vo, M.Jahazi, S.Yue: Metall. Mater. Trans. A39 (2008) 2965. 10.1007/s11661-008-9666-3Suche in Google Scholar

[15] S.L.Semiatin, V.Seetharaman, I.Weiss: Mater. Sci. Eng. A263 (1999) 257. 10.1016/S0921-5093(98)01156-3Suche in Google Scholar

[16] AMS 4899C: Titanium Alloy, Sheet, Strip, and Plate Ti-4.5Al-3V-2Fe-2Mo Annealed, ASTM Int., PA (2011).Suche in Google Scholar

[17] AMS 4964C: Titanium Alloy Bars, Wire, Forgings, and Rings Ti-4.5Al-3V-2Fe-2Mo Annealed, ASTM Int., PA (2011).Suche in Google Scholar

[18] ASTM A938–07: Standard Test Method for Torsion Testing of Wire, ASTM Int., PA (2013).Suche in Google Scholar

[19] S.Sadeghpour, S.M.Abbasi, M.Morakabati: J. Alloys Compd.650 (2015) 22. 10.1016/j.jallcom.2015.07.263Suche in Google Scholar

[20] A.Dehghan-Manshadi, R.J.Dippenaar: Mater. Sci. Eng. A552 (2012) 451. 10.1016/j.msea.2012.05.069Suche in Google Scholar

[21] W. Ch.Chung, L.W.Tsay, C.Chen: Mater. Trans.50 (2009) 544. 10.2320/matertrans.MRA2008370Suche in Google Scholar

[22] R.Srinivasan, I.Weiss, in: D.Eylon, R.R.Boyer, D.A.Koss (Eds.), Proceeings of a Symposium on Beta titanium alloys in the 1990's, Colorado (1993) 283.Suche in Google Scholar

[23] P.Wanjara, M.Jahazi, H.Monajati, S.Yue, J.-P.Immarigeon: Mater. Sci. Eng. A396 (2005) 50. 10.1016/j.msea.2004.12.005Suche in Google Scholar

[24] I.Philippart, H.J.Rack: Mater. Sci. Eng. A243 (1998) 196. 10.1016/S0921-5093(97)00800-9Suche in Google Scholar

[25] A.H.Sheikhali, M.Morakkabati, S.M.Abbasi, A.Rezaei: Int. J. Mater. Res.104 (2013) 1122. 10.3139/146.110965Suche in Google Scholar

[26] S.L.Semiatin, G.D.Lahoti: Metall. Trans. A12 (1981) 1719. 10.1007/BF02643753Suche in Google Scholar

[27] S.H.Cho, Y.C.Yoo: J. Mater. Sci.36 (2001) 4279. 10.1023/A:1017544000562Suche in Google Scholar

[28] A.Dehghan-Manshadi, M.R.Barnett, P.D.Hodgson: Metall. Mater. Trans. A39 (2008) 1371. 10.1007/s11661-008-9512-7Suche in Google Scholar

[29] S.H.Cho, Y.C.Yoo: J. Mat. Sci.36 (2001) 4267. 10.1023/A:1017544000562Suche in Google Scholar

[30] O.M.Ivasishin, P.E.Markovsky, Y.V.Matviychuk, S.L.Semiatin: Metall. Mater. Trans.34 A (2003) 147. 10.1007/s11661-003-0216-8Suche in Google Scholar

[31] A.Najafizadeh, J.J.Jonas, G.R.Stewart, E.I.Poliak: Metal. Mat. Trans. A37 (2006) 1899. 10.1007/s11661-006-0132-9Suche in Google Scholar

[32] A.Najafizadeh, J.J.Jonas: Int. J. ISSI3 (2006) 1.Suche in Google Scholar

[33] A.Dehghan-Manshadi, M.R.Barnett, P.D.Hodgson: Mater. Sci. Eng. A485 (2008) 664. 10.1016/j.msea.2007.08.026Suche in Google Scholar

[34] J.J.Jonas, C.Aranas, A.Fall, M.Jahazi: Mater. Des.113 (2017) 305. 10.1016/j.matdes.2016.10.039Suche in Google Scholar

Received: 2018-03-28
Accepted: 2018-07-23
Published Online: 2018-11-29
Published in Print: 2018-12-10

© 2018, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Original Contributions
  4. Dendritic structure formation of magnesium alloys for the manipulation of corrosion properties: Part 1 – microstructure
  5. The influence of twinning on plastic constitutive description of a magnesium alloy
  6. Effect of V and Zr microalloying, and heat treatment on microstructure and mechanical properties of secondary Al-7Si-3Cu-0.3Mg alloy
  7. Effect of heat treatment on microstructure, hardening and plasticity of a commercial Al–Zn–Mg–Cu alloy
  8. Microstructural evolution and mechanical properties of thixoformed 7075 aluminum alloy prepared by conventional and new modified SIMA processes
  9. Hot torsion behavior of SP-700 near beta titanium alloy in single and dual phase regions
  10. Effect of B4C in Ti-6Al-4V matrix on workability behavior of powder metallurgy composites during cold upsetting
  11. Synthesis of Ni/YSZ based anode and investigation of effect of PVA as pore-former upon porosity, microstructure and thermal behavior for potential use in solid oxide fuel cells (SOFCs)
  12. The corrosion behavior of porous Ni–Cr–Fe alloy in 2 mol L−1 alkaline solution
  13. Short Communications
  14. The grain growth in alumina compacts sintered under high pressure
  15. DGM News
  16. DGM News
https://doi.org/10.3139/146.111715
Schlagwörter für diesen Artikel
SP-700 titanium alloy; Hot torsion test; Dynamic recrystallization; Fractional softening; Phase transformation

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Original Contributions
  4. Dendritic structure formation of magnesium alloys for the manipulation of corrosion properties: Part 1 – microstructure
  5. The influence of twinning on plastic constitutive description of a magnesium alloy
  6. Effect of V and Zr microalloying, and heat treatment on microstructure and mechanical properties of secondary Al-7Si-3Cu-0.3Mg alloy
  7. Effect of heat treatment on microstructure, hardening and plasticity of a commercial Al–Zn–Mg–Cu alloy
  8. Microstructural evolution and mechanical properties of thixoformed 7075 aluminum alloy prepared by conventional and new modified SIMA processes
  9. Hot torsion behavior of SP-700 near beta titanium alloy in single and dual phase regions
  10. Effect of B4C in Ti-6Al-4V matrix on workability behavior of powder metallurgy composites during cold upsetting
  11. Synthesis of Ni/YSZ based anode and investigation of effect of PVA as pore-former upon porosity, microstructure and thermal behavior for potential use in solid oxide fuel cells (SOFCs)
  12. The corrosion behavior of porous Ni–Cr–Fe alloy in 2 mol L−1 alkaline solution
  13. Short Communications
  14. The grain growth in alumina compacts sintered under high pressure
  15. DGM News
  16. DGM News
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 15.11.2025 von https://www.degruyterbrill.com/document/doi/10.3139/146.111715/html?lang=de
Button zum nach oben scrollen