Ablation and mechanical investigation of carbon/rubber woven laminates for ultrahigh temperature applications
-
Yanhui Liu
Abstract
A novel needled carbon/rubber woven laminate was fabricated using heat vulcanizing silicone rubber and polyarylacetylene (PAA) as the matrix and two-dimensional carbon fiber (TCF) woven fabrics as the reinforcement phase. The tensile strength and hardness of the laminates were increased with the increasing of the content of PAA due to better compatibility between PAA and TCF. Ablation testing results demonstrated that the ablation rate firstly deceased and then increased with increasing of PAA content due to charring action of PAA and the formation of a loose ablation layer with cracks.
References
[1] Y.Liu, J.Su, Z.Yin, Y.Li, Y.Zhi, J.Gao: J. Polym. Eng.37 (2017) 521. 10.1515/polyeng-2016-0130Suche in Google Scholar
[2] Y.Liu, C.Ma, Y.Li, Z.Yin, Y.Zhi, J.Gao: Plast. Rubber. Compos.45 (2016) 430. 10.1080/14658011.2016.1243507Suche in Google Scholar
[3] H.Fu, C.Ma, N.Kuang, S.Luan: J. Aeronaut.20 (2007) 124. 10.1016/s1000-9361(07)60018-1Suche in Google Scholar
[4] W.Tseng, Y.Chen, G.Chang: Polym. Degrad. Stab.94 (2009) 2149. 10.1016/j.polymdegradstab.2009.09.008Suche in Google Scholar
[5] T.B.Caston, A.R.Murphy, T.A.L.Harris: J. Power Sources196 (2011) 709. 10.1016/j.jpowsour.2010.07.057Suche in Google Scholar
[6] D.Yang, W.Zhan, B.Jiang, Y.Guo: Composites Part A44 (2013) 70. 10.1016/j.compositesa.2012.09.002Suche in Google Scholar
[7] C.Xuan, L.long: Mater. Sci. Eng. A528 (2011) 6998. 10.1016/j.msea.2011.05.053Suche in Google Scholar
[8] L.Liu, Y.J.Song, Z.X.JiangX.Z.Zhang, L.N.Wu, Y.D.Huang: Appl. Surf. Sci.254 (2008) 5342. 10.1016/j.apsusc.2008.02.078Suche in Google Scholar
© 2018, Carl Hanser Verlag, München
Artikel in diesem Heft
- Contents
- Contents
- Original Contributions
- Influence of dislocations on precipitation processes in hot-extruded Al–Mn–Sc–Zr alloy
- Grain size gradient naturally prepared through recrystallization in rapidly solidified undercooled alloy melts
- Solidification behavior and microstructural characterization of Ni–Fe–W and Ni–Fe–W–Co matrix alloys
- Formation of amorphous interfacial layer between Zn-based alloy and SiC particles under ultrasonic-assisted brazing
- Microstructures and biocorrosion properties of biodegradable Mg–Zn–Y–Ca–xZr alloys
- Oxidation resistance and wettability of graphite/SiC composite
- Freeze linings in the Al2O3–CaO–SiO2 system
- Tribological properties of diamond-like carbon films deposited by vacuum arc
- Review
- Synthesis and characterization of magnesium-based hybrid composites – A review
- Short Communications
- Ablation and mechanical investigation of carbon/rubber woven laminates for ultrahigh temperature applications
- Effect of h-BN@Al2O3 on the microstructure and mechanical properties of Si3N4/TiC ceramic composite
- DGM News
- DGM News
Artikel in diesem Heft
- Contents
- Contents
- Original Contributions
- Influence of dislocations on precipitation processes in hot-extruded Al–Mn–Sc–Zr alloy
- Grain size gradient naturally prepared through recrystallization in rapidly solidified undercooled alloy melts
- Solidification behavior and microstructural characterization of Ni–Fe–W and Ni–Fe–W–Co matrix alloys
- Formation of amorphous interfacial layer between Zn-based alloy and SiC particles under ultrasonic-assisted brazing
- Microstructures and biocorrosion properties of biodegradable Mg–Zn–Y–Ca–xZr alloys
- Oxidation resistance and wettability of graphite/SiC composite
- Freeze linings in the Al2O3–CaO–SiO2 system
- Tribological properties of diamond-like carbon films deposited by vacuum arc
- Review
- Synthesis and characterization of magnesium-based hybrid composites – A review
- Short Communications
- Ablation and mechanical investigation of carbon/rubber woven laminates for ultrahigh temperature applications
- Effect of h-BN@Al2O3 on the microstructure and mechanical properties of Si3N4/TiC ceramic composite
- DGM News
- DGM News
