Home Tribological behavior of Fe3Al-60 wt.% Fe3AlC0.5 composite under air and vacuum conditions
Article
Licensed
Unlicensed Requires Authentication

Tribological behavior of Fe3Al-60 wt.% Fe3AlC0.5 composite under air and vacuum conditions

  • Yonghai Kang , Junying Hao , Zhuhui Qiao , Licai Fu , Weimin Liu and Jun Yang
Published/Copyright: October 10, 2014
Become an author with De Gruyter Brill
Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 105 Issue 10

Abstract

The tribological behavior of Fe3Al composite with 60 wt.% Fe3AlC0.5 under air and vacuum was studied. The composite exhibited a lower wear rate but somewhat higher friction coefficient under air than vacuum. The wear rates increased and the friction coefficients decreased with increasing the applied load under both conditions. The sub-layer of the worn surface under vacuum suffered from severe plastic deformation. This was not the case under air due to protection by surface oxide films. The dominant wear mechanisms were plastic deformation and adhesion under vacuum and oxidative wear and slight delamination under air.

Keywords: Intermetallics; Wear mechanism; Vacuum; Friction; Adhesion
* Correspondence address, Professor Junyin Hao, State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou, PR China, Tel: 86-931-4968264, Fax: 86-931-8277088, E-mail:

References

[1] N.S.Stoloff: Mater. Sci. Eng. A258 (1998) 1. 10.1016/S0921-5093(98)00909-5Search in Google Scholar

[2] C.T.Liu, E.P.George, P.J.Maziasz, J.H.Schneibel: Mater. Sci. Eng.A258 (1998) 84. 10.1016/S0921-5093(98)00910-1Search in Google Scholar

[3] J.Yang, J.Q.Ma, Q.L.Bi, W.M.Liu, Q.J.Xue: Mater. Sci. Eng.A490 (2008) 90. 10.1016/j.msea.2008.01.024Search in Google Scholar

[4] G.Sharma, P.K.Limaye, M.Sundararaman, N.L.Soni: Mater. Lett.61 (2007) 3345. 10.1016/j.matlet.2006.06.052Search in Google Scholar

[5] R.G.Baligidad, U.Prakash, A.Radhakrishna, R.V.Ramakrishna, P.K.Rao, N.B.Ballal: Scr. Mater.36 (1997) 105. 10.1016/S1359-6462(96)00340-5Search in Google Scholar

[6] V.S.Rao: Intermetallics11 (2003) 713. 10.1016/S0966-9795(03)00071-2Search in Google Scholar

[7] J.Yang, P.Q.La, W.M.Liu, Y.Hao: Mater. Sci. Eng.A382 (2004) 8. 10.1016/j.msea.2004.03.095Search in Google Scholar

[8] R.G.Baligidad, U.Prakash, A.Radhakrishna: Mater. Sci. Eng.A249 (1998) 97. 10.1016/S0921-5093(98)00580-2Search in Google Scholar

[9] R.G.Baligidad, U.Prakash, A.Radhakrishna: Intermetallics6 (1998) 765. 10.1016/S0966-9795(98)00050-8Search in Google Scholar

[10] R.G.Baligidad, A.Radhakrishna, U.Prakash: Mater. Sci. Eng.A257 (1998) 235. 10.1016/S0921-5093(98)00861-2Search in Google Scholar

[11] J.Yang, P.Q.La, W.M.Liu, J.Q.Ma, Q.J.Xue: Intermetallics13 (2005) 1184. 10.1016/j.intermet.2004.06.007Search in Google Scholar

[12] S.Venkatesan, D.A.Rigney: Wear153 (1992) 163. 10.1016/0043-1648(92)90268-DSearch in Google Scholar

[13] M.Sawa, D.A.Rigney: Wear119 (1987) 369. 10.1016/0043-1648(87)90042-1Search in Google Scholar

[14] M.Kazuhisa: Tribol. Int.32 (1999) 605. 10.1016/S0301-679X(99)00093-6Search in Google Scholar

[15] J.L.Endrino, J.J.Nainaparampil, J.E.Krzanowski: Surf. Coat. Technol.157 (2002) 95. 10.1016/S0257-8972(02)00138-XSearch in Google Scholar

[16] Y.Liu, D.Z.Yang, S.Y.He, W.L.Wu: Mater. Charact.50 (2003) 275. 10.1016/S1044-5803(03)00125-6Search in Google Scholar

[17] J.Q.Yang, Y.Liu, Z.Y.Ye, D.Z.Yang, S.Y.He: Surf. Coat. Technol.204 (2009) 705. 10.1016/j.surfcoat.2009.09.015Search in Google Scholar

[18] L.Wang, J.Q.Ma, J.Yang, Q.L.Bi, L.C.Fu, W.M.Liu: Wear268 (2010) 991. 10.1016/j.wear.2009.09.006Search in Google Scholar

[19] L.C.Fu, J.Yang, Q.L.Bi, S.Y.Zhu, W.M.Liu: Tribol. Lett.34 (2009) 185. 10.1007/s11249-009-9422-xSearch in Google Scholar

[20] Y.H.Kang, J.Yang, J.Q.Ma, L.C.Fu, Q.L.Bi, F.Li, W.M.Liu: Tribol. Int.51 (2012) 11. 10.1016/j.triboint.2012.02.010Search in Google Scholar

[21] R.Tyagi, S.K.Nath, S.Ray: Metall. Mater. Trans. A32 (2001) 359. 10.1007/s11661-001-0267-7Search in Google Scholar

[22] Y.S.Zhang, K.Wang, Z.Han, G.Liu: Wear262 (2007) 1463. 10.1016/j.wear.2006.07.002Search in Google Scholar

[23] J.Yang, P.Q.La, W.M.Liu, Q.J.Xue: Wear257 (2004) 104. 10.1016/j.wear.2003.10.012Search in Google Scholar

[24] M.Shafiei, A.T.Alpas: Metall. Mater. Trans.A38 (2007) 1621. 10.1007/s11661-007-9157-ySearch in Google Scholar

[25] M.Shafiei, A.T.Alpas: Wear265 (2008) 429. 10.1016/j.wear.2007.11.022Search in Google Scholar

[26] A.Devaraju, A.Elayaperumal: Int. J. Eng. Sci. Technol.2 (2010) 4137.Search in Google Scholar

Received: 2014-01-11
Accepted: 2014-03-19
Published Online: 2014-10-10
Published in Print: 2014-10-14

© 2014, Carl Hanser Verlag, München

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. Phase equilibria studies of the “MnO”–Al2O3–SiO2 system in equilibrium with metallic alloy. Part 1: Development of the technique and determination of liquidus isotherms between 1 423 K and 1 523 K
  5. Casting process optimization of a bimetal wear-resistant block using liquid–solid processing
  6. Characteristics of melt convection during Kyropoulos sapphire crystal growth
  7. A method for the formation of intergranular crystalline phases in liquid phase sintering
  8. Corrosion resistance of laser treated titanium alloy with B4C particles at the surface
  9. Effect of Cr and Mo doping on the electrochemical properties of freeze-dried LiCoO2
  10. Inhibition properties and adsorption behavior of olive leaf extract on N80 carbon steel in CO2-saturated brine solution
  11. Tribological behavior of Fe3Al-60 wt.% Fe3AlC0.5 composite under air and vacuum conditions
  12. Improving the surface topography of mild steel with the burnishing process
  13. Additional small-scale boundary effects on free vibration of carbon nanotubes and their macroscopic energy meaning
  14. Aqueous soluble gold nanoparticle synthesis using polyethyleneimine and reduced glutathione
  15. DGM News
  16. Personal
https://doi.org/10.3139/146.111106
Keywords for this article
Intermetallics; Wear mechanism; Vacuum; Friction; Adhesion

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. Phase equilibria studies of the “MnO”–Al2O3–SiO2 system in equilibrium with metallic alloy. Part 1: Development of the technique and determination of liquidus isotherms between 1 423 K and 1 523 K
  5. Casting process optimization of a bimetal wear-resistant block using liquid–solid processing
  6. Characteristics of melt convection during Kyropoulos sapphire crystal growth
  7. A method for the formation of intergranular crystalline phases in liquid phase sintering
  8. Corrosion resistance of laser treated titanium alloy with B4C particles at the surface
  9. Effect of Cr and Mo doping on the electrochemical properties of freeze-dried LiCoO2
  10. Inhibition properties and adsorption behavior of olive leaf extract on N80 carbon steel in CO2-saturated brine solution
  11. Tribological behavior of Fe3Al-60 wt.% Fe3AlC0.5 composite under air and vacuum conditions
  12. Improving the surface topography of mild steel with the burnishing process
  13. Additional small-scale boundary effects on free vibration of carbon nanotubes and their macroscopic energy meaning
  14. Aqueous soluble gold nanoparticle synthesis using polyethyleneimine and reduced glutathione
  15. DGM News
  16. Personal
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2025 De Gruyter Brill
Downloaded on 18.10.2025 from https://www.degruyterbrill.com/document/doi/10.3139/146.111106/html
Scroll to top button