Home Technology Optimization of process parameters in explosive cladding of titanium/stainless steel 304L plates
Article
Licensed
Unlicensed Requires Authentication

Optimization of process parameters in explosive cladding of titanium/stainless steel 304L plates

  • Padmanaban Tamilchelvan , Krishnamurthy Raghukandan and Somasundaram Saravanan
Published/Copyright: November 30, 2013
Become an author with De Gruyter Brill
Submit Manuscript Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 104 Issue 12

Abstract

Explosive cladding is a solid state welding process best suited for joining incompatible metals. The selection of process parameters viz., explosive mass ratio, stand off distance and initial angle of inclination dictate the nature of the cladding. Optimization of process parameters in explosive cladding of titanium–stainless steel 304L plates, based on two level three factorial design, is attempted to establish the influencing parameters. Analysis of variance was employed to find the linear, regression and interaction values. Mathematical models to estimate the responses-amplitude and wavelength were developed. The microstructure of the Ti–SS304L explosive clad interface reveals characteristic undulations concurrent with design expectations.

Keywords: Explosive cladding; Titanium; Stainless steel; Optimization; Microstructural characterization

Paper presented at 3rd International Conference on Recent Advances in Material Processing Technology (RAMPT'13), 07 – 09 January 2013, National Engineering College, K.R. Nagar, Kovilpatti, Tamilnadu, India

* Correspondence address, P. Tamilchelvan, Research Scholar, Department of Manufacturing Engineering, Annamalai University, Annamalai Nagar, Cuddalore District, Tamilnadu, India – 608002, Tel.: +91-9842023992, E-mail:

References

[1] M.Acarer, B.Gulenc, F.Findik: Mater. Des.24 (8) (2003) 659. 10.1016/S0261-3069(03)00066-9Search in Google Scholar

[2] F.Findik: Mater. Des.32 (3) (2011) 1081. 10.1016/j.matdes.2010.10.017Search in Google Scholar

[3] N.Kahraman, B.Gulenc, F.Findik: J. Mater. Proc. Techn.169 (2005) 127. 10.1016/j.jmatprotec.2005.02.264Search in Google Scholar

[4] A.Durgutlu, B.Gulenc, F.Findik: Mater. Des.26 (6) (2005) 497. 10.1016/j.matdes.2004.07.021Search in Google Scholar

[5] M.Acarer, B.Gulenc, F.Findik: J. Mater. Sci.39 (21) (2004) 6457. 10.1023/B:JMSC.0000044883.33007.20Search in Google Scholar

[6] K.Raghukandan: J. Mater. Proc. Techn.139 (1–3) (2003) 573.10.1016/S0924-0136(03)00539-9Search in Google Scholar

[7] L.Tricarico, R.Spina, D.Sorgente, M.Brandizzi: Mater. Des.30 (2009) 2693. 10.1016/j.matdes.2008.10.010Search in Google Scholar

[8] K.Raghukandan, P.Tamilchelvan, N.Meikandan: Mater. Sci. Forum566 (2008) 285. 10.4028/www.scientific.net/MSF.566.285Search in Google Scholar

[9] S.Saravanan, K.Raghukandan: Sci. Tech. Weld. Join.17 (2) (2012) 99. 10.1179/1362171811Y.0000000080Search in Google Scholar

[10] P.Manikandan, K.Hokamoto, A.A.Deribas, K.Raghukandan, R.Tomoshige: Mater. Trans.47 (8) (2006) 2049. 10.2320/matertrans.47.2049Search in Google Scholar

[11] S.A.A. AkbariMousavi, P. FarhadiSartangi: Mater. Des.30 (3) (2009) 459. 10.1016/j.matdes.2008.06.016Search in Google Scholar

[12] D.C.Montgomery, E.A.Peck, G.G.Vining: Introduction to linear regression analysis, Edition 3, NewYork, Wiley (2003).Search in Google Scholar

[13] S.V.Gladkovski, T.A.Trunina, E.A.Kokovikhin, D.I.Vichuzhanin, I.A.Golubkova: Met. Sci. Heat Treat.51(9–10) (2009) 444.10.1007/s11041-010-9190-0Search in Google Scholar

[14] B.Wronka: J. Mater. Sci.45 (15) (2010) 4078. 10.1007/s10853-010-4494-4Search in Google Scholar

[15] A.A.Berdychenko, B.S.Zlobin, L.B.Pervukhin, A.A.Shtertser: Comb. Expl. Sho. Waves39 (2) (2003) 232. 10.1023/A:1022977420337Search in Google Scholar

[16] S.A.A. AkbariMousavi, S.T.S.Al-Hassani, A.G.Atkins: Mater. Des.29 (7) (2008) 1334. 10.1016/j.matdes.2007.06.010Search in Google Scholar

[17] M.Sedighi, M.Honarpisheh: Mater. Des.37 (2012) 577. 10.1016/j.matdes.2011.10.022Search in Google Scholar

[18] N.Kahraman, B.Gulenc, F.Findik: Int. J. Imp. Eng.34 (2007) 1423. 10.1016/j.ijimpeng.2006.08.003Search in Google Scholar

[19] P.Manikandan, K.Hokamoto, M.Fujita, K.RaghukandanR.Tomoshige: J. Mater. Proc. Techn.195 (2008) 232. 10.1016/j.jmatprotec.2007.05.002Search in Google Scholar

[20] R.Kaçar, MAcarer: Mater. Sci. Eng. A.363 (2003) 290. 10.1016/S0921-5093(03)00643-9Search in Google Scholar

[21] H.R. ZareieRajani, S.A.A. AkbariMousavi, F. MadaniSani: Mater. Des.43 (2013) 467. 10.1016/j.matdes.2012.06.053Search in Google Scholar

[22] BingfengWang, WeiChen, JuanLi, ZhaolinLiu, XiebinZhu: Mater. Des.47 (2013) 74. 10.1016/j.matdes.2012.11.052Search in Google Scholar

[23] S.A.A.Akbari-Mousavi, L.M.Barrett, S.T.S.Al-Hassani: J. Mater. Proc. Tech.202 (2008) 224. 10.1016/j.jmatprotec.2007.09.028Search in Google Scholar

[24] S.Saravanan, K.Raghukandan: Mater. Manuf. Process.28 (2013) 589. 10.1080/10426914.2012.736665Search in Google Scholar

[25] Y.B.Yan, Z.W.Zhang, W.Shen, J.H.Wang, L.K.Zhang, B.A.Chin: Mater. Sci. Eng. A527 (2010) 2241. 10.1016/j.msea.2009.12.007Search in Google Scholar

Received: 2013-3-11
Accepted: 2013-7-9
Published Online: 2013-11-30
Published in Print: 2013-12-12

© 2013, Carl Hanser Verlag, München

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. Critical sizes for coherent to semicoherent transition in precipitates
  5. Thixoformability evaluation of AA2011 and AA2014 alloys
  6. Joint strength of friction stir welded AISI 304 austenitic stainless steels
  7. Optimization of process parameters in explosive cladding of titanium/stainless steel 304L plates
  8. Optimization of the hot rolling parameters for evaluation of the formability of Nb-microalloyed steel sheet by using the Taguchi method
  9. XPS measurements of LDX 2101 duplex steel surface after magnetoelectropolishing
  10. Phase equilibria of the Al-Cr-Pr ternary system at 773 K
  11. Processing and mechanical characterisation of monolithic silicon carbide ceramic consolidated by spark plasma sintering (SPS)
  12. Effect of Mn doping on the microstructure and dielectric properties of BaHf0.1Ti0.9O3 ceramics
  13. Nano hydroxyapatite–polysulfone coating on Ti-6Al-4V substrate by electrospinning
  14. Photocatalytic and self-cleaning properties of SiO2/TiO2/SiO2 nanostructured thin film
  15. Formation mechanism of manganese vanadate microtubes and their electrochemical sensing properties
  16. Modification of the luminescent properties of ZnS nanoparticles by the adsorbed species
  17. DGM News
  18. DGM News
https://doi.org/10.3139/146.110977
Keywords for this article
Explosive cladding; Titanium; Stainless steel; Optimization; Microstructural characterization

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. Critical sizes for coherent to semicoherent transition in precipitates
  5. Thixoformability evaluation of AA2011 and AA2014 alloys
  6. Joint strength of friction stir welded AISI 304 austenitic stainless steels
  7. Optimization of process parameters in explosive cladding of titanium/stainless steel 304L plates
  8. Optimization of the hot rolling parameters for evaluation of the formability of Nb-microalloyed steel sheet by using the Taguchi method
  9. XPS measurements of LDX 2101 duplex steel surface after magnetoelectropolishing
  10. Phase equilibria of the Al-Cr-Pr ternary system at 773 K
  11. Processing and mechanical characterisation of monolithic silicon carbide ceramic consolidated by spark plasma sintering (SPS)
  12. Effect of Mn doping on the microstructure and dielectric properties of BaHf0.1Ti0.9O3 ceramics
  13. Nano hydroxyapatite–polysulfone coating on Ti-6Al-4V substrate by electrospinning
  14. Photocatalytic and self-cleaning properties of SiO2/TiO2/SiO2 nanostructured thin film
  15. Formation mechanism of manganese vanadate microtubes and their electrochemical sensing properties
  16. Modification of the luminescent properties of ZnS nanoparticles by the adsorbed species
  17. DGM News
  18. DGM News
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2026 De Gruyter Brill
Downloaded on 1.2.2026 from https://www.degruyterbrill.com/document/doi/10.3139/146.110977/html
Scroll to top button