Skip to main content
Article
Licensed
Unlicensed Requires Authentication

Experimental study of phase equilibria in the “SnO2” – CaO – SiO2 system in air

  • , and
Published/Copyright: May 14, 2013
Become an author with De Gruyter Brill
Submit Manuscript Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 102 Issue 10

Abstract

Experimental studies have been conducted to determine the primary phases and liquidus temperatures in the “SnO2” – CaO – SiO2 system in air between 1693 and 1898 K, using high temperature equilibration and quenching followed by electron probe X-ray microanalysis. The following primary phase fields were identified: CaSiSnO5 (malayaite), Ca3Si2SnO9 (tricalcium tin silicate), CaSiO3 (pseudo-wollastonite), Ca2SiO4 (dicalcium silicate), SiO2 (tridymite and cristobalite), SnO2 (cassiterite) and CaSnO3 (calcium stannate).

Keywords: Primary phases; Liquidus temperatures; Equilibria; EPMA; “SnO2“ – CaO – SiO2
* Correspondence address Mr. Xiaoyong Xu, The Pyrosearch Centre at the School of Chemical Engineering The University of Queensland, Brisbane Qld 4072, Australia, Tel.: +61 7 33 65 36 66, Fax: +61 7 33 65 38 88, E-mail:

References

[1] P.A.Wright: Extractive Metallurgy of Tin, Elsevier Scientific Publishing Company, New York (1982).Search in Google Scholar

[2] Y.Takeda, A.Yazawa, P.P.Chit, H.Ujiie: Mater. Trans., JIM31 (1990) 793.Search in Google Scholar

[3] J.Li, P.Shrivatasta, Z.Gao, H.C.Zhang: IEEE Trans. Electronics Packaging Manufact.27 (2004) 33. 10.1109/TEPM.2004.830501Search in Google Scholar

[4] G.Eriksson, P.Wu, M.Blander, A.D.Pelton: Can. Metall. Q.33 (1994) 13.10.1179/000844394795539361Search in Google Scholar

[5] S.Takenouchi: Mineral. Deposita.6 (1971) 335. 10.1007/BF00201891Search in Google Scholar

[6] G.Blasse, M.A.Hamatr, D.J.W.Ijdo, J.R.PIaisler: Mater. Res. Bull.30 (1995) 967. 10.1016/0025-5408(95)00084-4Search in Google Scholar

[7] G.Pfaff: Mater. Sci. Eng. B-Solid State Mater. Adv. Technol.33 (1995) 156.10.1016/0921-5107(94)01188-5Search in Google Scholar

[8] E.Jak, P.C.Hayes, in: VII Intl. Conf. on Molten Slags Fluxes and Salts, SAIMM, Johannesburg, Cape Town, South Afica (2004) 85.Search in Google Scholar

[9] E.Jak, B.Zhao, S.Nikolic, P.C.Hayes, in: U. Waschki (Ed.), European Metallurgy Conference, GDMB Medienverlag, Düsseldorf, Germany (2007) 1789.Search in Google Scholar

[10] S.Nikolic, P.C.Hayes, E.Jak: Metall. Mater. Trans. B39 (2008) 179. 10.1007/s11663-008-9130-1Search in Google Scholar

[11] E.Jak, H.G.Lee, P.C.Hayes: Korean IMMJ1 (1995) 1.Search in Google Scholar

[12] E.Jak, P.C.Hayes: Mineral Processing and Extractive Metallurgy (TIMMC)117 (2008) 1.Search in Google Scholar

Received: 2010-3-26
Accepted: 2011-8-16
Published Online: 2013-05-14
Published in Print: 2011-10-01

© 2011, Carl Hanser Verlag, München

Articles in the same Issue

  1. Contents
  2. Contents
  3. Editorial
  4. Laudatio für Frau Prof. Dr.-Ing. Christina Berger
  5. Review
  6. Role of microalloying elements in the microstructure of hot rolled steels
  7. Original Contributions
  8. Experimental study of phase equilibria in the “SnO2” – CaO – SiO2 system in air
  9. Thermodynamic modeling of the Cr – S system
  10. Observation of early melting stages of an Al – Cu alloy in a temperature gradient
  11. Knudsen effusion mass spectrometric studies of the B2 phase in the Al – Co system
  12. Microstructure evolution in hypereutectoid graphitic steel
  13. The effect of thermal treatment on the structural properties of copper-containing sol-gel silica nanocomposites
  14. Electrospray deposition of thin copper-indium-diselenide films
  15. Morphology, fibrous composition and tensile properties of drag-silk produced by two species of orb spider
  16. Magnetic properties of Co0.5Zn0.5Fe2O4 nanopowders prepared by means of the template-assisted hydrothermal method
  17. Effects of aging and sheet thickness on the room temperature deformation behavior and in-plane anisotropy of cold rolled and solution treated Nimonic C-263 alloy sheet
  18. Thermal expansion/contraction behavior of AA7050 alloy in the as-cast condition relevant to thermomechanical simulation of residual thermal stresses
  19. Obtaining high formability of IF-galvanized steel tailor welded blanks by applying optimum CO2 laser welding parameters
  20. Investigation of the dependence of structural and mechanical properties of cement-bonded bauxite refractories on their process conditions
  21. The effects of curing medium on the flexural strength and water permeability of cementitious composites containing Fe2O3 nanofillers
  22. DGM News
  23. DGM News
https://doi.org/10.3139/146.110577
Keywords for this article
Primary phases; Liquidus temperatures; Equilibria; EPMA; “SnO2“ – CaO – SiO2

Articles in the same Issue

  1. Contents
  2. Contents
  3. Editorial
  4. Laudatio für Frau Prof. Dr.-Ing. Christina Berger
  5. Review
  6. Role of microalloying elements in the microstructure of hot rolled steels
  7. Original Contributions
  8. Experimental study of phase equilibria in the “SnO2” – CaO – SiO2 system in air
  9. Thermodynamic modeling of the Cr – S system
  10. Observation of early melting stages of an Al – Cu alloy in a temperature gradient
  11. Knudsen effusion mass spectrometric studies of the B2 phase in the Al – Co system
  12. Microstructure evolution in hypereutectoid graphitic steel
  13. The effect of thermal treatment on the structural properties of copper-containing sol-gel silica nanocomposites
  14. Electrospray deposition of thin copper-indium-diselenide films
  15. Morphology, fibrous composition and tensile properties of drag-silk produced by two species of orb spider
  16. Magnetic properties of Co0.5Zn0.5Fe2O4 nanopowders prepared by means of the template-assisted hydrothermal method
  17. Effects of aging and sheet thickness on the room temperature deformation behavior and in-plane anisotropy of cold rolled and solution treated Nimonic C-263 alloy sheet
  18. Thermal expansion/contraction behavior of AA7050 alloy in the as-cast condition relevant to thermomechanical simulation of residual thermal stresses
  19. Obtaining high formability of IF-galvanized steel tailor welded blanks by applying optimum CO2 laser welding parameters
  20. Investigation of the dependence of structural and mechanical properties of cement-bonded bauxite refractories on their process conditions
  21. The effects of curing medium on the flexural strength and water permeability of cementitious composites containing Fe2O3 nanofillers
  22. DGM News
  23. DGM News
Downloaded on 19.4.2026 from https://www.degruyterbrill.com/document/doi/10.3139/146.110577/html
Scroll to top button