Home Fundamental and applied aspects of laser surface engineering
Article
Licensed
Unlicensed Requires Authentication

Fundamental and applied aspects of laser surface engineering

  • J. Th. M. De Hosson , V. Ocelík , U. O. B. de Oliveira and D. I. Vainchtein
Published/Copyright: June 11, 2013
Become an author with De Gruyter Brill
Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 100 Issue 10

Abstract

The contribution to this jubilee issue of IJMR concentrates on the analysis of laser surface treatments. In particular laser cladding processes using coaxial and side set-ups are evaluated to determine the optimal processing window that prioritizes the clad quality and the efficiency of the coating method. The microstructural features in these so-called processing maps are illustrated with Inverse Pole Figure (IPF) mapping, texture pole figures and Electron Backscatter Pattern (EBSP) techniques. The distribution of stresses inside Co-based laser coating is measured with the so-called three-dimensional X-ray Diffraction microscopy (3DXRD) and it is found very dispersive, i. e. stresses may change from one grain to another considerably. The mean value of observed hydrostatic stress in all grains at specific laser track depth is gradually changed from tensile state in the upper part of the coating to the compressive state in its lower part close to the substrate. On the other hand the average value of shear stress component does not show any substantial change with depth.

Keywords: Laser technology; Surface engineering; Coating; Electron backscatter pattern, Residual stress
* Correspondence address, J. Th. M. De Hosson University of Groningen 9747 AG Groningen The Netherlands Phone: +31 50 363 4898 Fax: +31 50 363 4881 E-mail:

References

[1] J.I.Davydov, A.A.Zhukov: Fiz. i Chim. Obrab. Materialov1 (1969) 17–21.Search in Google Scholar

[2] J.H.Hwang, Y.S.Lee, D.Y.Kim: J. Mater. Eng. and Performance11 (2002) 294–299.10.1361/105994902770344105Search in Google Scholar

[3] W.J.Tomlinson, R.F.O'Connor, T.A.Spedding: Tribology International21 (1988) 302–305.10.1016/0301-679X(88)90106-5Search in Google Scholar

[4] J.A.Vreeling, V.Ocelík, J.T.M.De Hosson: Acta Mater.50 (2002) 4913–4924.10.1016/S1359-6454(02)00366-XSearch in Google Scholar

[5] Y.T.Pei, J.T.M.De Hosson: Acta Mater.49 (2001) 561–571.10.1016/S1359-6454(00)00364-5Search in Google Scholar

[6] J.A.Vreeling, V.Ocelík, Y.T.Pei, D.T.L.van Agterveld, J.Th.M.De Hosson: Acta Mater.48 (2000) 4225–4233.10.1016/S1359-6454(00)00278-0Search in Google Scholar

[7] V.Ocelík, D.T.A.Matthews, J.T.M.De Hosson: Surface and Coatings Technology, 197 (2005) 303–315.10.1016/j.surfcoat.2004.09.003Search in Google Scholar

[8] D.T.A.Matthews, V.Ocelík, J.T.M.De Hosson: Mater. Sci. Eng. A471 (2007) 155–164.10.1016/j.msea.2007.02.119Search in Google Scholar

[9] D.T.A.Matthews, V.Ocelík, J.T.M.De Hosson: J. Mater. Res.22 (2007) 460–470.10.1557/jmr.2007.0056Search in Google Scholar

[10] R.Vilar: J. of laser applications11 (1999) 64–79.10.2351/1.521888Search in Google Scholar

[11] N.B.Dahotre: Advanced Materials & Processes160 (2002) 35–39.Search in Google Scholar

[12] J.Th.M.De Hosson, V.Ocelík, Y.Pei: Surface Engineering with Lasers, in: H.Liang, G.E.Totten (Ed.): Surface Modifications and Processing, Publisher Marcel DekkerUSA, (2004) 603–669.Search in Google Scholar

[13] J.T.M.De Hosson: Laser synthesis and properties of ceramic coatings, in N.B.Dahotre, T.S.Sudarshan (Eds.): Intermetallic and Ceramic Coatings, M. Dekker, N. Y., 307–441.Search in Google Scholar

[14] W.M.Steen, V.M.Weerasinghe, P.Monson: High Power Lasers and Their Industrial Applications650 (1986) 226–243.10.1117/12.938104Search in Google Scholar

[15] J.Lin: J. Optics & Laser Technology31 (1999) 233–238.10.1016/S0030-3992(99)00046-8Search in Google Scholar

[16] A.Yakovlev, Ph.Bertrand, I.Smurov: Thin Solid Films453 (2004) 133–138.10.1016/j.tsf.2003.11.085Search in Google Scholar

[17] Ph.Bertrand, M.Doubenskaia, M.Ignatiev, I.Smurov, F.Campana, J.P.Jansen, B.Laget, in: T.S. Sudarshan, S.V. Joshi, G. Totten (Ed.): Optical Diagnostic, Thermal Spraying and Laser Cladding, International Conference on Advances in Surface Treatment: Research & Applications, ARCI Hyderabat, India, 2003.Search in Google Scholar

[18] J.-M.Jouvard, D.F.Grevey, F.Lemoine, A.B.Vannes: J. of Laser Applications9 (1987) 43–50.10.2351/1.4745444Search in Google Scholar

[19] D.W.Smith: Powder characterization, in: Encyclopaedia Mater. Sci. Eng5 (1986) 3859.Search in Google Scholar

[20] L.Costa, I.Felde, T.Reti, K.Zoltan, R.Colaço, R.Vilar, B.Veró: Mater. Science Forum414–415 (2003) 385–394.10.4028/www.scientific.net/MSF.414-415.385Search in Google Scholar

[21] R.Colaço, L.Costa, R.Guerra, R.VilarJ.Mazumder, O.Conde, R.Villar, W.Steen (Eds.): Laser Processing: Surface Treatment and Film Deposition, NATO ASI Series E: Applied Sciences 307, Kluwer Academic Publishers (1996) 421–429.Search in Google Scholar

[22] H.-J.Bartsch: Handbook of Mathematical Formulas (Academic Press, New York, 1974) 528.Search in Google Scholar

[23] V.Ocelík, U.de Oliveira, A.H.Pieren, J.T.M.De Hosson, in: T.S.Sudarshan, S.V.Joshi, G.Totten (Eds.): Thick Coating by Coaxial Laser Cladding, International Conference on Advances, Surface Treatment: Research & Applications, ARCI Hyderabat, India2003.Search in Google Scholar

[24] I.Felde, Z.Kálazi, B.Veró, T.Réti, G.Králik, O.Szabados, in: T.S.Sudarshan, M.Jeandin (Eds.): An experimental design technique for the approximation of process parameters in laser surface hardening, Surface Modification Technologies XIV, ASM International, Metals Park, Ohio and IOM Communications Ltd., UK, 2001.Search in Google Scholar

[25] I.Felde, T.Reti, K.Zoltan, L.Costa, R.Colaço, R.Vilar, B.Verö, in: T.S. Sudarshan, S.V. Joshi, G. Totten (Ed.): A Simple Technique to Estimate the Processing Window for Laser Clad Coatings, Proceedings from the 1st International Surface Engineering Congress and the 13th IFHTSE Congress, 7–10 October 2002, Columbus, Ohio, ASM International 2003, 237–242.Search in Google Scholar

[26] M.Bamberger, W.D.Kaplan, B.Medres, L.Shepeleva: J. of Laser Applications10 (1998) 29–33.10.2351/1.521829Search in Google Scholar

[27] Z.H.Shen, S.Y.Zhang, J.Lu, X.W.Ni: Optics & Laser Technology33 (2001) 533–537.10.1016/S0030-3992(01)00005-6Search in Google Scholar

[28] A.F.A.Hoadley, M.Rappaz, M.Zimmermann: Metall. Trans. B22 (1991) 101–109.10.1007/BF02672531Search in Google Scholar

[29] R.D.Gray: A history of the Haynes Stellite Company, Kokomo, Ind., Stellite Division (Cabot Corporation, 1974).Search in Google Scholar

[30] C.T.Sims, N.S.Stoloff, W.C.Hagel: Superalloys II (John Wiley and Sons, New York, 1987).Search in Google Scholar

[31] C.P.Sullivan, J.D.Varin, M.J.DonachieJr.: Metals Engineering Quarterly9 (1969) 16.Search in Google Scholar

[32] J.T.M.De Hosson, J.L.De Mol van Otterloo: Surface Engineering.13 (1997) 471–481.10.1179/sur.1997.13.6.471Search in Google Scholar

[33] J.L.De Mol van Otterloo, J.T.M.De Hosson: Acta Mater.45 (1997) 1225–1236.10.1016/S1359-6454(96)00250-9Search in Google Scholar

[34] F.R.Morral, L.Habraken, D.Coutsouradis, J.M.Drapier, M.Urbain: Metals Engineering Quarterly ASM9 (1969) 1–16.Search in Google Scholar

[35] U.de Oliveira, V.Ocelík, J.T.M.De Hosson: Surface & Coatings Technology197 (2005) 127–136.10.1016/j.surfcoat.2004.06.029Search in Google Scholar

[36] H.Bunge: Texture Analysis in Materials Science (Butterworths, London (1982).10.1016/B978-0-408-10642-9.50010-6Search in Google Scholar

[37] D.S.Li, H.Garmestani, S.Schoenfeld: Scripta Mater.49 (2003) 867–872.10.1016/S1359-6462(03)00443-3Search in Google Scholar

[38] H.F.Poulsen, in: Three dimensional X-ray diffraction microscopy, Springer-Verlag, Berlin-Heidelberg, 2004.10.1007/b97884Search in Google Scholar

[39] E.M.Lauridsen, S.Schmidt, R.M.Suter, H.F.Poulsen: J. Appl. Crystallogr.34 (2001) 744–750.10.1107/S0021889801014170Search in Google Scholar

[40] H.F.Poulsen, in: Three dimensional X-ray diffraction microscopy, Springer-Verlag, Berlin-Heidelberg, 2004.10.1007/b97884Search in Google Scholar

[41] D.W.J.Cruickshank, H.J.Juretschke, N.Kato (Eds.): P.P. Ewald and his dynamical theory of X-ray diffraction (Oxford University Press, Oxford1992).Search in Google Scholar

[42] Y.D.Wang, H.Tian, A.D.Stoica, X.-L.Wang, P.K.Liaw, J.W.Richardson: Nature Mater.2 (2003) 101–106.10.1038/nmat812Search in Google Scholar

[43] U.O.B.de Oliveira, V.Ocelík, J.T.M.De Hosson, in: J.T.M.De Hosson, C.A.Brebbia, S.-I.Nishida (Eds.): Residual stresses in Co-based laser claddings investigated by lab X-rays and synchrotron duffraction techniques, Computer Methods and Experimental Measurements for Surface Effects and Contact Mechanics VII, WIT Press, Southhampton2005, 241–250.Search in Google Scholar

[44] U.O.B.de Oliveira, V.Ocelík, J.T.M.De Hosson: Advanced Materials Research 15–17 (2007) 153–158.Search in Google Scholar

[45] V.Ocelík, U.O.B.de Oliveira, M.de Boer, J.T.M.De Hosson: Surf. Coat. Technol.201 (2007) 5875–5883.10.1016/j.surfcoat.2006.10.044Search in Google Scholar

[46] U.O.B.de Oliveira, V.Ocelík, J.T.M.De Hosson: Surf. Coat. Technol.201 (2007) 6363–6371.10.1016/j.surfcoat.2006.12.013Search in Google Scholar

[47] Y.D.Wang, R.Lin Peng, X.-L.Wang, R.L.McGreevy: Acta Mater.50 (2002) 1717–1734.10.1016/S1359-6454(02)00021-6Search in Google Scholar

[48] V.Ocelík, J.Bosgra, J.T.M.De Hosson: Surface & Coating Technology203 (2009) 3189–3196.10.1016/j.surfcoat.2009.03.050Search in Google Scholar

Received: 2009-5-20
Accepted: 2009-7-15
Published Online: 2013-06-11
Published in Print: 2009-10-01

© 2009, Carl Hanser Verlag, München

Articles in the same Issue

  1. Contents
  2. Contents
  3. Introduction
  4. Introduction
  5. G. Petzow: Laudation for Peter Paul Schepp
  6. Dr. Schepp's retirement after 20 years of service was celebrated
  7. Preface to Feature Articles
  8. “SURFACE and INTERFACE ENGINEERING”
  9. Feature
  10. Thermodynamics of reactions and phase transformations at interfaces and surfaces
  11. Oxidation of palladium: from single crystal surfaces towards nanoparticles
  12. On the high-temperature oxidation of MCrAlY coatings
  13. Conducting polymers for corrosion protection: a review
  14. Fundamental and applied aspects of laser surface engineering
  15. Low-temperature gaseous surface hardening of stainless steel: the current status
  16. Foreword
  17. Foreword
  18. Editorial
  19. The scientific work of Charles Crussard (1916–2008)
  20. Review
  21. Charles Crussard's early contributions: Recrystallization in situ and a Grain Boundary study with J. Friedel and B. Cullity
  22. Magnetohydrodynamics applied to materials processing
  23. Charles Crussard's contribution to sheet metal forming and participation in IDDRG
  24. Glide of dislocations in non-octahedral planes of fcc metals: a review
  25. The deformation stage II of face-centered cubic crystals: Fifty years of investigations
  26. Nucleation and growth during primary recrystallization of certain metals and alloys with a face-centered cubic structure: Formation of the cube texture
  27. Basic
  28. Andrade creep revisited
  29. Application of cluster dynamics modeling to the precipitation in aluminum alloys
  30. On the effect of pre-recovery on subsequent recrystallization
  31. The interplay between grain boundaries and disclinations in condensed matter physics
  32. Plasticity of nanocrystalline materials: a critical viewpoint
  33. Thermoelectric power applied to metallurgy: principle and recent applications
  34. Notifications
  35. People
https://doi.org/10.3139/146.110203
Keywords for this article
Laser technology; Surface engineering; Coating; Electron backscatter pattern, Residual stress

Articles in the same Issue

  1. Contents
  2. Contents
  3. Introduction
  4. Introduction
  5. G. Petzow: Laudation for Peter Paul Schepp
  6. Dr. Schepp's retirement after 20 years of service was celebrated
  7. Preface to Feature Articles
  8. “SURFACE and INTERFACE ENGINEERING”
  9. Feature
  10. Thermodynamics of reactions and phase transformations at interfaces and surfaces
  11. Oxidation of palladium: from single crystal surfaces towards nanoparticles
  12. On the high-temperature oxidation of MCrAlY coatings
  13. Conducting polymers for corrosion protection: a review
  14. Fundamental and applied aspects of laser surface engineering
  15. Low-temperature gaseous surface hardening of stainless steel: the current status
  16. Foreword
  17. Foreword
  18. Editorial
  19. The scientific work of Charles Crussard (1916–2008)
  20. Review
  21. Charles Crussard's early contributions: Recrystallization in situ and a Grain Boundary study with J. Friedel and B. Cullity
  22. Magnetohydrodynamics applied to materials processing
  23. Charles Crussard's contribution to sheet metal forming and participation in IDDRG
  24. Glide of dislocations in non-octahedral planes of fcc metals: a review
  25. The deformation stage II of face-centered cubic crystals: Fifty years of investigations
  26. Nucleation and growth during primary recrystallization of certain metals and alloys with a face-centered cubic structure: Formation of the cube texture
  27. Basic
  28. Andrade creep revisited
  29. Application of cluster dynamics modeling to the precipitation in aluminum alloys
  30. On the effect of pre-recovery on subsequent recrystallization
  31. The interplay between grain boundaries and disclinations in condensed matter physics
  32. Plasticity of nanocrystalline materials: a critical viewpoint
  33. Thermoelectric power applied to metallurgy: principle and recent applications
  34. Notifications
  35. People
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2025 De Gruyter Brill
Downloaded on 2.10.2025 from https://www.degruyterbrill.com/document/doi/10.3139/146.110203/html?lang=en
Scroll to top button