Startseite Effect of V2O5 doping on the microstructure and local composition of textured Sr0.4Ba0.6Nb2O6 ceramics
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Effect of V2O5 doping on the microstructure and local composition of textured Sr0.4Ba0.6Nb2O6 ceramics

  • Xian-Hao Wang , Hui Gu , Qing-Wei Huang und Li-Ping You
Veröffentlicht/Copyright: 23. Mai 2013
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 98 Heft 3

Abstract

A comparison of phases and the microstructures of textured Sr0.4Ba0.6Nb2O6 ceramics without and with V2O5 addition was carried out using transmission and analytical electron microscopy. The dopant was not found in Sr0.4Ba0.6Nb2O6 grains but in the inter-granular regions, including both grain boundary and second phase. Grain boundaries in the sample without V2O5 are clean, but those in the V2O5-doped sample exhibit a variety of structures, with and without an amorphous film of variable thickness. In general the vanadium excess follows the same trend of film width, while the Sr excess is generally negative and the Ba excess is positive, suggesting that the amorphous films at grain boundaries are rich in V and Ba and deficient in Nb and Sr. The second phase was determined as Ba3V4O13 phase containing small amounts of Sr and Nb. Such V- and Ba-rich inter-granular liquids promoted the densification and texturing, and affected the dielectric constant at low frequency but not the Curie temperature.

Keywords: Strontium barium niobate; Liquid-phase sintering; Textured microstructure; Grain boundary film; Analytical electron microscopy
* Correspondence address, Prof. H. Gu State Key Lab of High Performance Ceramics andSuperfine Microstructures Shanghai Institute of Ceramics Chinese Academy of Sciences Dingxi Road 1295, Shanghai 2005, P. R. of China Tel.: +86 21 5241 2318 Fax: +86 21 5241 3122 E-mail:

References

[1] N.S.VanDamme, A.E.Sutherland, L.Jones, K.Bridger, S.R.Winzer: J. Am. Ceram. Soc.74 (1991) 1785.10.1111/j.1151-2916.1991.tb07789.xSuche in Google Scholar

[2] R.R.Neurgaonkar, W.K.Cory: J. Opt. Soc. Am. B3 (1986) 274.10.1364/JOSAB.3.000274Suche in Google Scholar

[3] S.I.Lee, W.K.Choo: ferroelectrics87 (1988) 209.10.1080/00150198808201383Suche in Google Scholar

[4] R.R.Neurgaonkar, M.H.Kalisher, T.C.Lim, E.J.Staples, K.I.Keester: Mater. Res. Bull.15 (1980) 1235.10.1016/0025-5408(80)90025-2Suche in Google Scholar

[4] A.Moreno-Gobbi, M.Pérez, G.Paolini, C.A.Negreira, D.Garcíra, J.A.Eiras: J. Alloys Comp.310 (2000) 29.10.1016/S0925-8388(00)01002-1Suche in Google Scholar

[6] C.Duran, S.T.Mckinstry, G.L.Messing: J. Mater. Res.17 (2002) 2399.10.1557/JMR.2002.0351Suche in Google Scholar

[7] C.Duran, S.T.Mckinstry, G.L.Messing: J. Am. Ceram. Soc.83 (2001) 2203.10.1111/j.1151-2916.2000.tb01536.xSuche in Google Scholar

[8] Q.W.Huang, L.H.Zhu, J.Xu, P.L.Wang, H.Gu, Y.B.Cheng: J. Europ. Ceram. Soc.25 (2005) 957.10.1016/j.jeurceramsoc.2003.12.027Suche in Google Scholar

[9] S.Nishiwai, J.Takahashi, K.Kodsira: J. Ceram. Soc. Jpn.103 (1995) 1246.10.2109/jcersj.103.1246Suche in Google Scholar

[10] S.Nishiwai, J.Takahashi, K.Kodsira: J. Ceram. Soc. Jpn.104 (1996) 435.10.2109/jcersj.104.435Suche in Google Scholar

[11] G.Cliff, G.W.Lorimer: J. Micros.103 (1975) 203.10.1111/j.1365-2818.1975.tb03895.xSuche in Google Scholar

[12] Z.Horita, K.Ichitani, T.Sano, M.Nemoto: Philo. Mag. A59 (1989) 939.10.1080/01418618908209829Suche in Google Scholar

[13] X.H.Wang, H.Gu: Determination of foil thickness and contamination effect in binary and ternary niobates in EDS analysis. Unsubmitted.Suche in Google Scholar

[14] H.Gu, R.M.Cannon, M.Rühle: J. Mater. Res.13 (1998) 376.10.1557/JMR.1998.0050Suche in Google Scholar

[15] J.R.Carruthers, M.Grasso: J. Electrochem. Soc.117 (1970) 1426.10.1149/1.2407336Suche in Google Scholar

Received: 2006-8-29
Accepted: 2006-12-12
Published Online: 2013-05-23
Published in Print: 2007-03-01

© 2007, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Basic
  4. Texture and microstructure evolution of ECAP processed AlMg1Mn0.14 alloy
  5. Modelling grain refinement in fcc metals during equal-channel angular pressing by route “C”
  6. Fabrication of high strength nanostructured aluminium alloys by hydrostatic extrusion
  7. Comparison of the plastic strain distribution during equal-channel angular pressing (ECAP) using 2D and 3D FEM modeling
  8. Deformation twins in ultrafine grained commercial aluminum
  9. Compressive behaviour of ultrafine-grained AA6063T6 over a wide range of strains and strain rates
  10. Grain refinement response during twist extrusion of an Al-0.13% Mg alloy
  11. Preparation of NiO–LiFeO2 solid solutions: the role of mechanical and thermal treatments
  12. Applied
  13. Fatigue strength and fracture behavior of steels with and without interstitial carbon at room temperature in air
  14. The influence of Nd on the corrosion behavior of electroless-deposited Fe–P
  15. Time-dependent directional solidification of binary Al–Cu alloys in the initial transient
  16. Effect of V2O5 doping on the microstructure and local composition of textured Sr0.4Ba0.6Nb2O6 ceramics
  17. Microstructure and mechanical properties of AZ91D alloy prepared by a semi-solid diecasting process
  18. Development of SMD 32.768 kHz tuning fork type crystals
  19. Notifications
  20. DGM News
https://doi.org/10.3139/146.101455
Schlagwörter für diesen Artikel
Strontium barium niobate; Liquid-phase sintering; Textured microstructure; Grain boundary film; Analytical electron microscopy

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Basic
  4. Texture and microstructure evolution of ECAP processed AlMg1Mn0.14 alloy
  5. Modelling grain refinement in fcc metals during equal-channel angular pressing by route “C”
  6. Fabrication of high strength nanostructured aluminium alloys by hydrostatic extrusion
  7. Comparison of the plastic strain distribution during equal-channel angular pressing (ECAP) using 2D and 3D FEM modeling
  8. Deformation twins in ultrafine grained commercial aluminum
  9. Compressive behaviour of ultrafine-grained AA6063T6 over a wide range of strains and strain rates
  10. Grain refinement response during twist extrusion of an Al-0.13% Mg alloy
  11. Preparation of NiO–LiFeO2 solid solutions: the role of mechanical and thermal treatments
  12. Applied
  13. Fatigue strength and fracture behavior of steels with and without interstitial carbon at room temperature in air
  14. The influence of Nd on the corrosion behavior of electroless-deposited Fe–P
  15. Time-dependent directional solidification of binary Al–Cu alloys in the initial transient
  16. Effect of V2O5 doping on the microstructure and local composition of textured Sr0.4Ba0.6Nb2O6 ceramics
  17. Microstructure and mechanical properties of AZ91D alloy prepared by a semi-solid diecasting process
  18. Development of SMD 32.768 kHz tuning fork type crystals
  19. Notifications
  20. DGM News
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 13.10.2025 von https://www.degruyterbrill.com/document/doi/10.3139/146.101455/html?lang=de
Button zum nach oben scrollen