Startseite Comparison of the plastic strain distribution during equal-channel angular pressing (ECAP) using 2D and 3D FEM modeling
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Comparison of the plastic strain distribution during equal-channel angular pressing (ECAP) using 2D and 3D FEM modeling

  • V. S. Zhernakov , I. N. Budilov , I. V. Alexandrov und I. J. Beyerlein
Veröffentlicht/Copyright: 23. Mai 2013
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 98 Heft 3

Abstract

The plastic flow of a copper billet calculated using 2D and 3D finite element modeling are compared during a single extrusion of equal-channel angular pressing. Both models predict deformation heterogeneity irrespective of material behavior, die geometry and friction conditions. On the symmetry plane where the numerical approaches can be compared, their strain distributions differ, especially as the processing conditions deviate from the ideal conditions. Overall the three-dimensional finite element model calculates lower plastic strains than the two-dimensional model.

Keywords: ECAP (ECAE); Severe plastic deformation; Equivalent stress distributions; 3D finite element analysis
* Correspondence address, Professor Igor Alexandrov Head Of Department Of Physics Ufa State Aviation Technical University 12 K. Marx St., Ufa 450000, Russia Tel.: +7 3472 73 79 77 Fax: +7 3472 73 34 22 E-Mail:

References

[1] R.Z.Valiev, R.K.Islamgaliev, I.V.Alexandrov: Prog. Mater. Sci.45 (2000) 103.10.1016/S0079-6425(99)00007-9Suche in Google Scholar

[2] J.R.Bowen, A.Gholinia, S.M.Roberts, P.B.Prangnell: Mater. Sci. Eng. A287 (2000) 87.10.1016/S0921-5093(00)00834-0Suche in Google Scholar

[3] H.S.Kim, M.H.Seo, S.I.Hong: Mater. Sci. Eng. A291 (2000) 86.10.1016/S0921-5093(00)00970-9Suche in Google Scholar

[4] S.Li, M.A.M.Bourke, I.J.Beyerlein, D.J.Alexander, B.Clausen: Mater. Sci. Eng. A382 (2004) 217.10.1016/j.msea.2004.04.067Suche in Google Scholar

[5] W.J.Kim, J.C.Namgung, J.K.Kim: Scripta Mater.53 (2005) 293.10.1016/j.scriptamat.2005.04.014Suche in Google Scholar

[6] S.W.Chung, H.Somekawa, T.Kinoshita, W.J.Kim, K.Higashi: Scripta Mater.50 (2004) 1079.10.1016/j.scriptamat.2003.11.062Suche in Google Scholar

[7] I.N.Budilov, I.V.Alexandrov, Y.V.Lukaschuk, I.J.Beyerlein, in: Y.T.Zhu, T.G.Langdon, R.Z.Valiev, S.L.Semiatin, D.H.Shin, T.C.Lowe (Eds.), Ultrafine Grained Materials III, TMS (The Minerals, Metals & Materials Society), Warrendale, Pennsylvania (2004) 193.Suche in Google Scholar

[8] W.J.Kim, J.C.Namkung: Mater. Sci. Eng. A412 (2005) 287.10.1016/j.msea.2005.08.222Suche in Google Scholar

[9] S.Li, S.R.Kalidindi, I.J.Beyerlein: Mater. Sci. Eng. A410 (2005) 207.10.1016/j.msea.2005.08.029Suche in Google Scholar

[10] I.J.Beyerlein, C.N.Tomé: Mater. Sci. Eng. A380 (2004) 171.10.1016/j.msea.2004.03.063Suche in Google Scholar

[11] S.Li, I.J.Beyerlein, C.T.Necker, D.J.Alexander, M.A.M.Bourke: Acta Mater.52 (2004) 4859.10.1016/j.actamat.2004.06.042Suche in Google Scholar

[12] S.Li, I.J.Beyerlein, C.T.Necker: Acta Mater.54 (2006) 1397.10.1016/j.actamat.2005.11.020Suche in Google Scholar

[13] I.J.Beyerlein, S.Li, C.T.Necker, D.J.Alexander, C.N.Tomé: Phil. Mag.85 (2005) 1359.10.1080/09500830500040940Suche in Google Scholar

[14] H.S.Kim, M.H.Seo, S.I.Hong: Mater. Sci. Eng. A291 (2000) 86.10.1016/S0921-5093(00)00970-9Suche in Google Scholar

[15] S.C.Baik, Y.Estrin, R.J.Hellmig, H.T.Jeong, H.G.Brokmeier, H.S.Kim: Z. Metallkd.94 (2003) 1189.Suche in Google Scholar

[16] D.J.Alexander, I.J.Beyerlein: Mater. Sci. Eng. A410 (2005) 480.10.1016/j.msea.2005.08.149Suche in Google Scholar

[17] I.J.Beyerlein, D.J.Alexander, C.N.Tomé: J. Mater. Sci., in press (2007).Suche in Google Scholar

[18] I.J.Beyerlein, C.N.Tomé, in: Y.T.Zhu, T.G.Langdon, Z.Horita, M.J.Zehetbauer, S.L.Semiatin, T.C.Lowe (Eds.), Ultrafine Grained Materials IV, TMS (2006) 63.Suche in Google Scholar

[19] MSC Mark Super Form Command Reference, Version 2002. Appendix Charter 6: Material Properties. MSC Software Corporation.Suche in Google Scholar

Received: 2006-10-17
Accepted: 2006-12-14
Published Online: 2013-05-23
Published in Print: 2007-03-01

© 2007, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Basic
  4. Texture and microstructure evolution of ECAP processed AlMg1Mn0.14 alloy
  5. Modelling grain refinement in fcc metals during equal-channel angular pressing by route “C”
  6. Fabrication of high strength nanostructured aluminium alloys by hydrostatic extrusion
  7. Comparison of the plastic strain distribution during equal-channel angular pressing (ECAP) using 2D and 3D FEM modeling
  8. Deformation twins in ultrafine grained commercial aluminum
  9. Compressive behaviour of ultrafine-grained AA6063T6 over a wide range of strains and strain rates
  10. Grain refinement response during twist extrusion of an Al-0.13% Mg alloy
  11. Preparation of NiO–LiFeO2 solid solutions: the role of mechanical and thermal treatments
  12. Applied
  13. Fatigue strength and fracture behavior of steels with and without interstitial carbon at room temperature in air
  14. The influence of Nd on the corrosion behavior of electroless-deposited Fe–P
  15. Time-dependent directional solidification of binary Al–Cu alloys in the initial transient
  16. Effect of V2O5 doping on the microstructure and local composition of textured Sr0.4Ba0.6Nb2O6 ceramics
  17. Microstructure and mechanical properties of AZ91D alloy prepared by a semi-solid diecasting process
  18. Development of SMD 32.768 kHz tuning fork type crystals
  19. Notifications
  20. DGM News
https://doi.org/10.3139/146.101450
Schlagwörter für diesen Artikel
ECAP (ECAE); Severe plastic deformation; Equivalent stress distributions; 3D finite element analysis

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Basic
  4. Texture and microstructure evolution of ECAP processed AlMg1Mn0.14 alloy
  5. Modelling grain refinement in fcc metals during equal-channel angular pressing by route “C”
  6. Fabrication of high strength nanostructured aluminium alloys by hydrostatic extrusion
  7. Comparison of the plastic strain distribution during equal-channel angular pressing (ECAP) using 2D and 3D FEM modeling
  8. Deformation twins in ultrafine grained commercial aluminum
  9. Compressive behaviour of ultrafine-grained AA6063T6 over a wide range of strains and strain rates
  10. Grain refinement response during twist extrusion of an Al-0.13% Mg alloy
  11. Preparation of NiO–LiFeO2 solid solutions: the role of mechanical and thermal treatments
  12. Applied
  13. Fatigue strength and fracture behavior of steels with and without interstitial carbon at room temperature in air
  14. The influence of Nd on the corrosion behavior of electroless-deposited Fe–P
  15. Time-dependent directional solidification of binary Al–Cu alloys in the initial transient
  16. Effect of V2O5 doping on the microstructure and local composition of textured Sr0.4Ba0.6Nb2O6 ceramics
  17. Microstructure and mechanical properties of AZ91D alloy prepared by a semi-solid diecasting process
  18. Development of SMD 32.768 kHz tuning fork type crystals
  19. Notifications
  20. DGM News
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 13.10.2025 von https://www.degruyterbrill.com/document/doi/10.3139/146.101450/html?lang=de
Button zum nach oben scrollen