Effect of copper or carbon fiber addition to the 3D printing of polylactid samples
-
L. Zárybnická
,
D. Machová
Abstract
This paper presents the effect of additives on the quality of a product created by 3D print. The product is created by the most widely used 3D printing method - Fused Deposition Modeling (FDM). Polylactic acid (PLA) filaments are tested without and with the addition of carbon fibers or copper. The specimens are characterized by different methods, such as mechanical testing, measuring roughness by digital microscope with a large depth of field and thermal analysis. In fact, FDM is a problematic process with numerous criterions that affect printing quality. Printing parameters such as print temperature, pad temperature, print speed for 3D printing, printing orientation etc. have an important impact on the performance and quality of FDM components. Due to the correct parameters, the product of the required quality with a longer service life is obtained. The results of testing show that the quantity and choice of the right ingredient has a major impact on the mechanical properties and overall quality of the investigated product.
© 2020 by Walter de Gruyter Berlin/Boston
Artikel in diesem Heft
- CONTENTS
- Materials Testing
- FACHBEITRÄGE
- New alloy development from modified cast Ni-base superalloy GTD-111 with additions of Al, Ni and/or Co prepared by vacuum arc melting process
- Enhancing a twist beam suspension system conceptual design using population-based optimization methods
- Influence of alumina whisker or nano-carbon contents on the microstructure and mechanical properties of CuZrTiAlNi refractory high entropy alloy composites
- Mechanical properties and fatigue behavior of CO2 laser beam welded armor steel joints
- Microstructure and properties of a laser cladded NiCrBSi alloy coating
- Dynamic response and damage assessment of spherical robot GFRP spherical shell under low velocity impact
- Influence of temperature on structural-phase changes and physical properties of ceramics on the basis of aluminum oxide and silicon
- Effect of the temperature gradient on hot cracking susceptibility for electron beam welding Alloy 247 LC
- Effect of copper or carbon fiber addition to the 3D printing of polylactid samples
- Theoretical evaluation of abrasive wear behavior of B4C/ FeCrC coating layer evaluated by a Taguchi approach
- Effect of the welding parameters on the surface morphology of resistance spot welded AISI 304 stainless steel joints
- Sine-cosine optimization algorithm for the conceptual design of automobile components
- Design and optimization of an electromechanical actuator for the latch of a foldable vehicle seat
- Design and analysis of a pressure vessel according to EU 2014/29
- BEZUGSQUELLEN
- IMPRESSUM
Artikel in diesem Heft
- CONTENTS
- Materials Testing
- FACHBEITRÄGE
- New alloy development from modified cast Ni-base superalloy GTD-111 with additions of Al, Ni and/or Co prepared by vacuum arc melting process
- Enhancing a twist beam suspension system conceptual design using population-based optimization methods
- Influence of alumina whisker or nano-carbon contents on the microstructure and mechanical properties of CuZrTiAlNi refractory high entropy alloy composites
- Mechanical properties and fatigue behavior of CO2 laser beam welded armor steel joints
- Microstructure and properties of a laser cladded NiCrBSi alloy coating
- Dynamic response and damage assessment of spherical robot GFRP spherical shell under low velocity impact
- Influence of temperature on structural-phase changes and physical properties of ceramics on the basis of aluminum oxide and silicon
- Effect of the temperature gradient on hot cracking susceptibility for electron beam welding Alloy 247 LC
- Effect of copper or carbon fiber addition to the 3D printing of polylactid samples
- Theoretical evaluation of abrasive wear behavior of B4C/ FeCrC coating layer evaluated by a Taguchi approach
- Effect of the welding parameters on the surface morphology of resistance spot welded AISI 304 stainless steel joints
- Sine-cosine optimization algorithm for the conceptual design of automobile components
- Design and optimization of an electromechanical actuator for the latch of a foldable vehicle seat
- Design and analysis of a pressure vessel according to EU 2014/29
- BEZUGSQUELLEN
- IMPRESSUM
