Startseite Compression testing of additively manufactured continuous carbon fiber-reinforced sandwich structures
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Compression testing of additively manufactured continuous carbon fiber-reinforced sandwich structures

  • Patrick Striemann , Martin Eichenhofer , Daniel Schupp , Michael Niedermeier , Daniel Huelsbusch und Frank Walther
Veröffentlicht/Copyright: 15. November 2018
Veröffentlichen auch Sie bei De Gruyter Brill
Manuskript einreichen Informationen für Autor*innen
Materials Testing
Aus der Zeitschrift Materials Testing Band 60 Heft 9

Abstract

The novel, additive manufacturing technique, continuous lattice fabrication, combines the advantages of continuous fiber-reinforcement with those of additive manufacturing. This enables the generation of fiber-reinforcement within a single layer and especially along an out-of-plane load path inside all spatial dimensions. This study is a test-related evaluation of sandwich panels with lattice core structures modifying a compression test. The specimens were manufactured differentially via plug and bond and automatically using continuous lattice fabrication. Additionally, the spatial arrangement of the rods within the lattice core structure varied in terms of base area. The ultra-lightweight sandwich panels have lattice core structures with core densities < 10 mg × cm−3. The material testing was performed by a modified compression test at room temperature. The damage analysis of the single rods shows current deficits and future potentials for optimization of lattice core structures. It could be shown that sandwich panels exhibit a compression strength of up to 0.30 MPa at a core density of 6.57 mg × cm−3. Using a dimensionless lightweight index demonstrates a mechanical performance on a level comparable with that of selected core materials.

Kurzfassung

Das neuartige Verfahren Continuous Lattice Fabrication kombiniert die Vorteile einer kontinuierlichen Faserverstärkung und der additiven Fertigung. Dabei kann die Faserverstärkung nicht nur innerhalb einzelner Schichten, sondern auch kraftflussgerecht (out-of-plane) im dreidimensionalen Raum generiert werden. Ziel dieses Beitrags ist eine testbasierte Bewertung von Sandwichstrukturen mit fachwerkähnlichen Kernstrukturen durch die Modifikation eines Druckversuchs. Dafür wurden Proben differentiell mit Steck- und Klebeverbindungen sowie automatisch mittels continuous lattice fabrication gefertigt. Zusätzlich wurde die räumliche Anordnung der Fachwerkstäbe, durch verschiedene Grundflächen und Stabwinkel, variiert. Ultraleichtbau-Strukturen mit fachwerkähnlichen Kernstrukturen haben Kerndichten kleiner 10 mg × cm−3. Die grundlegende werkstoffmechanische Untersuchung wurde mit Hilfe eines modifizierten einachsigen Druckversuchs bei Raumtemperatur durchgeführt. Die erarbeitete Systematik zur Schadensanalyse legt zukünftiges Optimierungspotential des noch jungen Verfahrens offen. Es konnte gezeigt werden, dass die Sandwichelemente mit einer Kernstrukturdichte von 6.57 mg × cm−3 eine Druckfestigkeit von bis zu 0.30 MPa aufweisen. Durch Auswertung einer dimensionslosen Leichtbaukennzahl konnte gezeigt werden, dass die Kennwerte der entwickelten Strukturen auf einem ähnlichen Niveau mit ausgewählten technischen Kernmaterialien liegen.

Keywords: Additive manufacturing; continuous fiber-reinforcement; sandwich; core material; compression strength
*Correspondence Address, Patrick Striemann, M.Eng., Laboratory of Material Testing, University of Applied Sciences, Ravensburg-Weingarten, Doggenriedstraße, D-88250 Weingarten, Germany, E-mail:

Patrick Striemann, born in 1990, studied Mechanical Engineering with a specialization in development and engineering design at the University of Applied Sciences (UAS) Ravensburg-Weingarten, Germany and received his Bachelor's degree in 2015. In 2017 he successfully completed a Master's degree in Technology Management & Optimization at UAS Ravensburg-Weingarten. Since then he has been working as a research assistant at the Laboratory of Material Testing at UAS Ravensburg-Weingarten. In the past years, he has focused on the additive manufacturing of continuous fiber-reinforcements.

Martin Eichenhofer, born in 1988, obtained his Bachelor's degree in Mechanical Engineering at the University of Applied Sciences Ravensburg-Weingarten, Germany followed by a Master's degree in Mechanical Engineering at ETH Zurich, Switzerland and a post-graduate Master's degree in Economics at the Collège des Ingénieurs, Paris, France. He specializes in functional design, processing and mechanics of composite materials. While working on his Master's thesis, he developed a new processing route for the continuous fabrication of composite materials (CLF). He is particularly interested in the symbiosis of digital fabrication and load tailored design.

Daniel Schupp, born in 1991, studied Mechanical Engineering with an emphasis on designing and developing at the University of Applied Sciences (UAS) Ravensburg-Weingarten, Germany. He received his Bachelor's degree in 2015, focusing on the development of new products for Bosch Power Tools. After that, he studied Technical Management at the UAS Ravensburg-Weingarten and received his Master's degree in 2017. Since 2015, he has been working for the Laboratory of Material Testing at UAS Ravensburg-Weingarten. His research mainly focuses on quasi-static testing of fiber-reinforced materials and the development and manufacturing of ultra-lightweight parts for aircrafts.

Prof. Dr.-Ing. Michael Niedermeier, born in 1962, studied Mechanical Engineering at the TU Munich, Germany from 1983 to 1988. After that, he worked as a scientific assistant at IKB at ETH Zurich, Switzerland. The topic of his PhD thesis was the investigation and characterization of the diaphragm forming of advanced thermoplastic composites. From 1995 to 1997 he was employed as R&D engineer in the field of new technologies/composites at Schindler Waggon AG, Altenrhein, Switzerland. Subsequently, he headed the department Joining and Forming with the additional function Program Manager Lightweight Structures at Alusuisse (later ALCAN) in Neuhausen, Switzerland, until 2003. Since 2003 he has been Professor at UAS Ravensburg-Weingarten University, Germany, Faculty of Mechanical Engineering, for lightweight design and composite materials and is head of the Laboratory of Material Testing.

Daniel Huelsbusch, born in 1986, studied Mechanical Engineering with an emphasis on technical management and materials science at the TU Dortmund University, Germany, where he received his diploma degree in February 2013 after focusing on joining techniques for fiber-reinforced polymers at BMW group. Since then he has been working as a scientific assistant and group leader for “Composites” at the Department of Materials Test Engineering (WPT) at the TU Dortmund University, Germany, and was appointed general Senior Engineer in 2015. His research is mainly focused on the fatigue properties of fiber-reinforced polymers, including the determination of deformation behavior, by advanced hysteresis measurements, and the corresponding damage propagation by in situ computed tomography.

Prof. Dr.-Ing. Frank Walther, born in 1970, studied Mechanical Engineering majoring in Materials Science and Engineering at the TU Kaiserslautern University, Germany. There, he finished his PhD on the fatigue assessment of railway wheel steels in 2002 and his habilitation on physical measurement techniques for microstructural-based fatigue assessment and lifetime calculation of metals in 2007. At Schaeffler AG in Herzogenaurach, Germany, he headed the Public Private Partnership within Corporate Development from 2008 to 2010. Since 2010 he has been Professor for Materials Test Engineering (WPT) at the TU Dortmund University, Germany. His research portfolio includes the determination of structure-property relationships of metal- and polymer-based materials and components under fatigue loading from LCF to the VHCF range, taking the influence of manufacturing and joining processes as well as service loading and corrosion deterioration into account. Prof. Walther has published more than 200 research papers and conference proceedings and maintains close scientific contact with institutions and industries in materials science and engineering field worldwide.

References

1 A.Bellini, S.Güceri: Mechanical characterization of parts fabricated using fused deposition modeling, Rapid Prototyping Journal9 (2003), No. 4, pp. 252–26410.1108/13552540310489631Suche in Google Scholar

2 A. R.Torrado, D. A.Roberson: Failure analysis and anisotropy evaluation of 3D-printed tensile test specimens of different geometries and print raster patterns, Journal of Failure Analysis and Prevention16 (2016), No. 1, pp. 154–16410.1007/s11668-016-0067-4Suche in Google Scholar

3 A. M.Forster: Materials testing standards for additive manufacturing of polymer materials: State of the art and standards applicability, National Institute of Standards and Technology, Gaithersburg, USA (2015), pp. 1–4510.6028/NIST.IR.8059Suche in Google Scholar

4 O.Huber, H.Klaus: Cellular composites in lightweight sandwich applications, Materials Letter63 (2009), No. 13–14, pp. 1117–112010.1016/j.matlet.2008.11.059Suche in Google Scholar

5 X.Zheng, H.Lee, T. H.Weisgraber, M.Shusteff, J.DeOtte, E. B.Duoss, J. D.Kuntz, M. M.Biener, Q.Ge, J. A.Jackson, S. O.Kucheyev, N. X.Fang, C. M.Spadaccini: Ultralight, ultrastiff mechanical metamaterials, Science344 (2014), No. 6190, pp. 1373–137710.1126/science.1252291Suche in Google Scholar

6 M.Eichenhofer, J. C. H.Wong, P.Ermanni: Continuous lattice fabrication of ultra-lightweight composite structures, Elsevier Additive Manufacturing18 (2017), pp. 48–5710.1016/j.addma.2017.08.013Suche in Google Scholar

7 F.Eichenhofer, M.Eichenhofer: Method for producing a framework, Germany (2015), Patent number: WO2015169414A1, pp. 1–39Suche in Google Scholar

8 M.Eichenhofer, J. I.Maldonado, F.Klunker, P.Ermanni: Analysis of processing conditions for a novel 3D-composite production technique, Proc. 20th International Conference on Composite Materials ICCM20, Copenhagen (2015), pp. 1–12Suche in Google Scholar

9 D. L.DuQuesnay, T. H.Topper, M. T.Yu: The effect of notch radius on the fatigue notch factor and the propagation of short cracks, Mechanical Engineering (1986), pp. 323–335Suche in Google Scholar

10 H.Fan, W.Yang, B.Wang, Y.Yan, Q.Fu, D.Fang, Z.Zhuang: Design and manufacturing of a composite lattice structure reinforced by continuous carbon fibers, Elsevier Tsinghua Science & Technology11 (2005), No. 5, pp. 515–52210.1016/S1007-0214(06)70228-0Suche in Google Scholar

11 C.Schneider, M. N.Velea, S.Kazemahvazi, D.Zenkert: Compression properties of novel thermoplastic carbon fibre and poly-ethylene terephthalate fibre composite lattice structures, Elsevier Materials & Design65 (2015), pp. 1110–112010.1016/j.matdes.2014.08.032Suche in Google Scholar

12 C. R.Schultheisz, A. M.Waas: Compressive failure of composites, Part I: Testing and micromechanical theories, Elsevier Aerospace Science32 (1996), No. 1, pp. 1–4210.1016/0376-0421(94)00002-3Suche in Google Scholar

13 N. A.Fleck, D.Liu: Microbuckle initiation from a patch of large amplitude fibre waviness in a composite under compression and bending, Elsevier European Journal of Mechanics – A/Solids20 (2001), No. 1, pp. 23–3710.1016/S0997-7538(00)01124-4Suche in Google Scholar

14 Y.Verreman, N.Limodin: Fatigue notch factor and short crack propagation, Elsevier Engineering Fracture Mechanics75 (2008), No. 6, pp. 1320–133510.1016/j.engfracmech.2007.07.005Suche in Google Scholar

15 B.Klein: Leichtbau-Konstruktion, 10th Ed., Springer Vieweg, Wiesbaden, Germany (2013), pp. 23–3710.1007/978-3-658-02272-3Suche in Google Scholar

16 Plascore Inc: PN2 Aerospace Grade Aramid Fiber Honeycomb, Zeeland, USA (2017)Suche in Google Scholar

17 Evonik Resource Efficiency GmbH: Technical information: ROHACELL® A, Darmstadt, Germany (2017)Suche in Google Scholar

18 AirexAG: Data Sheet AIREX® R82, Sins, Switzerland (2011)Suche in Google Scholar

19 AirexAG: Data Sheet AIREX® C70, Sins, Switzerland (2011)Suche in Google Scholar

20 AirexAG: Data Sheet BALTEK® SB, Sins; Switzerland (2016)Suche in Google Scholar

21 Evonik Resource Efficiency GmbH: Technical information ROHACELL® S, Darmstadt, Germany (2017)Suche in Google Scholar

Published Online: 2018-11-15
Published in Print: 2018-09-30

© 2018, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Inhalt/Contents
  2. Contents
  3. Fachbeiträge/Technical Contributions
  4. Compression testing of additively manufactured continuous carbon fiber-reinforced sandwich structures
  5. Microstructure and mechanical properties of nano-carbon reinforced Cu-based powder metallurgy friction materials produced by hot isostatic pressing
  6. Thermo-mechanical testing of TiO2 functional coatings using friction stir processing
  7. Ternary melt blend based on poly (lactic acid)/chitosan and cloisite 30B: A study of microstructural, thermo-mechanical and barrier properties
  8. Untersuchungen zur verlässlichen Messung der Härte nach dem UCI – Verfahren (Ultrasonic Contact Impedance)
  9. Electrochemical impedance spectroscopy of sand of varied particle size and water content using the three-electrode system
  10. Recycling of LM25 aluminum alloy scraps
  11. Mechanical fracture characterization of adhesive interfaces: Introducing a new concept for evaluating adhesive quality
  12. Effect of welding processes on mechanical and microstructural properties of S275 structural steel joints
  13. Essential Work of Fracture: Bestimmung des gültigen Ligamentbereiches mittels digitaler 3D-Bildkorrelation
  14. Synthesis, properties and EDM behavior of 10 wt.-% ZrB2 reinforced AA7178 matrix composites
  15. Solid particle erosion wear behavior of severe plastically deformed AA7075 alloys
  16. Performance of coated and uncoated carbide/cermet cutting tools during turning
  17. Assessment of soft materials for anthropomorphic soft robotic fingertips
  18. Application of the grey based Taguchi method and Deform-3D for optimizing multiple responses in turning of Inconel 718
https://doi.org/10.3139/120.111216
Schlagwörter für diesen Artikel
Additive manufacturing; continuous fiber-reinforcement; sandwich; core material; compression strength

Artikel in diesem Heft

  1. Inhalt/Contents
  2. Contents
  3. Fachbeiträge/Technical Contributions
  4. Compression testing of additively manufactured continuous carbon fiber-reinforced sandwich structures
  5. Microstructure and mechanical properties of nano-carbon reinforced Cu-based powder metallurgy friction materials produced by hot isostatic pressing
  6. Thermo-mechanical testing of TiO2 functional coatings using friction stir processing
  7. Ternary melt blend based on poly (lactic acid)/chitosan and cloisite 30B: A study of microstructural, thermo-mechanical and barrier properties
  8. Untersuchungen zur verlässlichen Messung der Härte nach dem UCI – Verfahren (Ultrasonic Contact Impedance)
  9. Electrochemical impedance spectroscopy of sand of varied particle size and water content using the three-electrode system
  10. Recycling of LM25 aluminum alloy scraps
  11. Mechanical fracture characterization of adhesive interfaces: Introducing a new concept for evaluating adhesive quality
  12. Effect of welding processes on mechanical and microstructural properties of S275 structural steel joints
  13. Essential Work of Fracture: Bestimmung des gültigen Ligamentbereiches mittels digitaler 3D-Bildkorrelation
  14. Synthesis, properties and EDM behavior of 10 wt.-% ZrB2 reinforced AA7178 matrix composites
  15. Solid particle erosion wear behavior of severe plastically deformed AA7075 alloys
  16. Performance of coated and uncoated carbide/cermet cutting tools during turning
  17. Assessment of soft materials for anthropomorphic soft robotic fingertips
  18. Application of the grey based Taguchi method and Deform-3D for optimizing multiple responses in turning of Inconel 718
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 23.10.2025 von https://www.degruyterbrill.com/document/doi/10.3139/120.111216/html
Button zum nach oben scrollen