Startseite Variation regulation of the acoustic emission energy parameter during the failure process of granite under uniaxial compression
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Variation regulation of the acoustic emission energy parameter during the failure process of granite under uniaxial compression

  • Chunlai Wang , Tiancai Bao , Hui Lu , Lu Liu , Zhijiang Lu , Weiqiang Li und Qiwei Yu
Veröffentlicht/Copyright: 31. August 2015
Veröffentlichen auch Sie bei De Gruyter Brill
Manuskript einreichen Informationen für Autor*innen
Materials Testing
Aus der Zeitschrift Materials Testing Band 57 Heft 9

Abstract

The AE energy characteristics of granite specimens were tested experimentally under uniaxial compression to investigate the variation regulation of acoustic emission (AE) energy during the granite failure process. The results show that the AE energy accompanies rock deformation and failure during the entire loading process. With stress increase, AE energy of granite specimens is in dynamic variation. There is a fine corresponding relationship between AE energy and stress. Under low stress levels, AE energy is relative low and remains stable. As stress increases, in the plastic deformation stage, AE energy rapidly increases and remains at a high level indicating intense energy which is released before rock failure. This phenomenon could be considered as the precursor for rock failure. Moreover, the corresponding time point where the AE energy release rate reaches the maximum is determined as the critical point for predicting rock failure. Then AE energy sharply decreases in the failure stage and rock instability occurs.

Kurzfassung

Um das Variationsgesetz der Schallemissionsenergie während des Versagens von Granit zu untersuchen, wurden experimentelle Untersuchungen zu den Charakteristika der Schallemissionsenergie von Granitproben unter einachsiger Druckbeanspruchung durchgeführt. Die Ergebnisse zeigen, dass die Schallemissionsenergie die Gesteinsverformung und das Versagen während des gesamten Belastungsprozesses begleitet. Wenn die Spannung zunimmt, ist die Schallemissionsenergie unter dynamischer Variation. Es besteht eine Abhängigkeit zwischen der Schallemissionsenergie und der Spannung. Bei niedrigen Spannungsniveaus ist die Schallemissionsenergie klein und bleibt stabil. Wenn die Spannung zunimmt, steigt die Schallemissionsernergie im Bereich der plastischen Verformung rapide an und verbleibt auf hohem Niveau, was darauf hindeutet, dass seine intensive Energie freigesetzt wird, bevor das Gestein versagt. Dieses Phänomen kann als Vorankündigung für das Gesteinsversagen gedeutet werden. Darüber hinaus wurde der entsprechende Zeitpunkt, an dem die Freisetzungsrate der Schallemissionsernergie den maximalen Wert erreicht, als kritischer Punkt zur Vorhersage des Gesteinsversagens ermittelt. Danach nimmt die Schallemissionsenergie im Versagensstadium rapide ab und es tritt Instabilität des Gesteins auf.

§Correspondence Address, Wang Chunlai, Faculty of Resources and Safety Engineering, China University of Mining & Technology Beijing, Ding 11, Xueyuan Road, Haidian District, Beijing, P. R. China, P.C. 100083. E-mail:

Chunlai Wang, born in 1976, works as Professor in the Faculty of Resources and Safety Engineering, China University of Mining & Technology Beijing, China. The author has studied control of mine dynamic disasters and early warning technology for many years. Up tonow, he has published over 50 academic papers and holds 5 invention patents in China.

Tiancai Bao, born in 1991, is a postgraduate at China University of Mining & Technology Beijing, China. He obtained his bachelor degree there in 2014. His research interests mainly focus on the control of mine dynamic disasters and acoustic emission testing. He has attended the general programs of the national natural science foundation of China.

Hui Lu, born in 1990, is a postgraduate at China University of Mining & Technology Beijing, China. He obtained his bachelor degree at Henan Polytechnic University, China in 2013. His research interests mainly focus on the development of nondestructive materials testing technology and acoustic emission testing. He has published several academic papers and holds 2 invention patents in China.

Lu Liu, born in 1991, is a postgraduate at China University of Mining & Technology Beijing, China. He obtained his bachelor degree at Taiyuan University of Technology, China in 2014. His research interests mainly focus on the stability control of surrounding rocks in underground mining and micro seismic monitoring technology.

Zhijiang Lu, born in 1989, is a postgraduate at China University of Mining & Technology Beijing, China. He obtained his bachelor degree at North China Institute of Science and Technology in 2013. His research interests mainly focus on the control of surrounding rocks and dynamic disasters in underground mining.

Weiqiang Li, born in 1992, is an undergraduate at China University of Mining & Technology Beijing, China. His research interests mainly focus on the control of surrounding rocks in underground mining and micro seismic monitoring technology. He has attended the national students’ innovation and entrepreneurship training program in past years.

Qiwei Yu, born in 1991, is a postgraduate at China University of Mining & Technology Beijing, China. He obtained his bachelor degree there in 2014. His research interests mainly focus on the stability control of surrounding rocks in underground mining and mining technology. He has attended the national students’ innovation and entrepreneurship training program in the past years.

References

1 S. J.Ternowchek, T. J.Gandy, M. V.Calva, T. S.Patterson: Acoustic emission and ultrasonic testing for mechanical integrity, ASTM Special Technical Publication1353 (1999), pp. 79–9210.1520/STP15782SSuche in Google Scholar

2 J. L.Knill, J. A.Franklin, A. W.Malone: A study of acoustic emission from stressed rock, International Journal of Rock Mechanics and Mining Sciences & Geomechanics Abstracts5 (1968), No. 1, pp. 87–8810.1016/0148-9062(68)90025-9Suche in Google Scholar

3 D. E. W.Stone, P. F.Dingwall: Acoustic emission parameters and their interpretation, NDT International10 (1977), No. 2, pp. 51–6210.1016/0308-9126(77)90079-7Suche in Google Scholar

4 M.Mirabile: Acoustic emission energy and mechanisms of plastic deformation and fracture, Non-destructive Testing8 (1975), No. 2, pp. 77–8410.1016/0029-1021(75)90157-7Suche in Google Scholar

5 L.Deng, L.Yan, R. G.Deng: Present situation and consideration of rock burst hazard, Advanced Materials Research250 (2011), pp. 136–14710.4028/www.scientific.net/AMR.250-253.136Suche in Google Scholar

6 M. C.He, J. L.Miao, J. L.Feng: Rock burst process of limestone and its acoustic emission characteristics under true-triaxial unloading conditions, International Journal of Rock Mechanics and Mining Sciences47 (2010), No. 2, pp. 286–29810.1016/j.ijrmms.2009.09.003Suche in Google Scholar

7 E. N.Landis, L.Baillon: Experiments to relate acoustic emission energy to fracture energy of concrete, Journal of Engineering Mechanics128 (2002), No. 6, pp. 698–7010.1061/(ASCE)0733-9399(2002)128:6(698)Suche in Google Scholar

8 R. VidyaSagar, B. K. RaghuPrasad: An experimental study on acoustic emission energy as a quantitative measure of size independent specific fracture energy of concrete beams, Construction and Building Materials25 (2011), No. 5, pp. 2349–235710.1016/j.conbuildmat.2010.11.033Suche in Google Scholar

9 B. K. RaghuPrasad, R. VidyaSagar: Relationship between AE energy and fracture energy of plain concrete beams: Experimental study, Journal of Materials in Civil Engineering20 (2008), No. 3, pp. 212–22010.1061/(ASCE)0899-1561(2008)20:3(212)Suche in Google Scholar

10 R. VidyaSagar, B. K. RaghuPrasad: AE energy release during the fracture of HSC beams, Magazine of Concrete Research61 (2009), No. 6, pp. 419–43510.1680/macr.2009.61.6.419Suche in Google Scholar

11 R. VidyaSagar, B. K. RaghuPrasad: A review of recent developments in parametric based acoustic emission techniques applied to concrete structure, Nondestructive Testing and Evaluation27 (2012), No. 1, pp. 47–6810.1080/10589759.2011.589029Suche in Google Scholar

12 M.Bourchak, I. R.Farrow, I. P.Bond, C. W.Rowland, F.Menan: Acoustic emission energy as a fatigue damage parameter for CFRP composites, International Journal of Fatigue29 (2007), No. 3, pp. 457–47010.1016/j.ijfatigue.2006.05.009Suche in Google Scholar

13 S.Muralidhara, B. K. R.Prasad, H.Eskandari: Fracture process zone size and true fracture energy of concrete using acoustic emission, Construction and Building Materials24 (2010), No. 4, pp. 479–48610.1016/j.conbuildmat.2009.10.014Suche in Google Scholar

14 A.Carpinteri, F.Cardone, G.Lacidogna: Energy emissions from failure phenomena: Mechanical, electromagnetic, nuclear, Experimental Mechanics50 (2010), No. 8, pp. 1235–124310.1007/s11340-009-9325-7Suche in Google Scholar

15 P. L. P.Wasantha, P. G.Ranjith, S. S.Shao: Energy monitoring and analysis during deformation of bedded-sandstone: Use of acoustic emission, Ultrasonics54 (2014), No. 1, pp. 217–22610.1016/j.ultras.2013.06.015Suche in Google Scholar

16 C. L.Wang: Identification and early warning method for rock mass instability, Disaster Advances6 (2013), No. 12, pp. 101–105Suche in Google Scholar

17 C. L.Wang: Identification of early-warning key point for rock mass instability using acoustic emission/micro seismic activity monitoring, International Journal of Rock Mechanics and Mining Sciences71 (2014), No. 10, pp. 171–17510.1016/j.ijrmms.2014.06.009Suche in Google Scholar

18 C. L.Wang, A. X.Wu, X. H.Liu, X. W.Ji, X.Li, Q. W.Yan, X.Huang, X.Hou: Mechanisms of micro seismic events occurred in deep hard-rock mine of China, Proc. of the 7th International Symposium on Rock burst and Seismicity in Mines, Vol. 1, Rinton Press, Paramus, USA (2009), pp. 245–251Suche in Google Scholar

19 A. X.Wu, C. L.Wang, X. H.Liu, X. W.Ji, X.Li, Q. W.Yan, X.Huang, X.Hou: Characteristics and mechanisms of rock burst in deep mine in China, Proc. of the 7th International Symposium on Rock burst and Seismicity in Mines, Vol. 2, Rinton Press, Paramus, USA (2009), pp. 1037–1040Suche in Google Scholar

20 G. T.Shen, R. S.Geng, S. F.Liu: Parameter analysis of acoustic emission signals, Nondestructive Testing24 (2002), No. 2, pp. 72–771000-6656(2002)02-0072-06Suche in Google Scholar

Published Online: 2015-08-31
Published in Print: 2015-09-01

© 2015, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Inhalt/Contents
  2. Inhalt
  3. Fachbeiträge/Technical Contributions
  4. Adhesive tensile testing of atmospheric plasma sprayed zinc coating on a 1.4301 substrate
  5. Fatigue strength of nodular cast iron with regard to heavy-wall applications
  6. Mechanical and corrosion properties of friction stir welded joints of Al-Cu alloy 2219-T87
  7. The effect of using heat treated ulexite and cashew in automotive friction materials
  8. Residual stress relaxation in welded large components
  9. Variation regulation of the acoustic emission energy parameter during the failure process of granite under uniaxial compression
  10. Iznik tiles: A new production technology and respective characterization
  11. Quality during milling of a glass fiber reinforced polymer composite
  12. Effect of abrasive water jet turning process parameters on surface roughness and material removal rate of AISI 1050 steel
  13. Influence of cutting parameters on the chip-tool interface temperature during the turning of Waspaloy
  14. Effects of the thixocasting injection velocity on tensile properties of an A357 Al alloy
  15. Solid mold investment casting – A replication process for open-cell foam metal production
  16. Design of an impact testing machine for polymer films by the free falling dart procedure
  17. Mechanical and electrical properties of Sb-Ga50Au10In40 alloys
  18. CFD simulation of particulate flow in a spiral concentrator
https://doi.org/10.3139/120.110776

Artikel in diesem Heft

  1. Inhalt/Contents
  2. Inhalt
  3. Fachbeiträge/Technical Contributions
  4. Adhesive tensile testing of atmospheric plasma sprayed zinc coating on a 1.4301 substrate
  5. Fatigue strength of nodular cast iron with regard to heavy-wall applications
  6. Mechanical and corrosion properties of friction stir welded joints of Al-Cu alloy 2219-T87
  7. The effect of using heat treated ulexite and cashew in automotive friction materials
  8. Residual stress relaxation in welded large components
  9. Variation regulation of the acoustic emission energy parameter during the failure process of granite under uniaxial compression
  10. Iznik tiles: A new production technology and respective characterization
  11. Quality during milling of a glass fiber reinforced polymer composite
  12. Effect of abrasive water jet turning process parameters on surface roughness and material removal rate of AISI 1050 steel
  13. Influence of cutting parameters on the chip-tool interface temperature during the turning of Waspaloy
  14. Effects of the thixocasting injection velocity on tensile properties of an A357 Al alloy
  15. Solid mold investment casting – A replication process for open-cell foam metal production
  16. Design of an impact testing machine for polymer films by the free falling dart procedure
  17. Mechanical and electrical properties of Sb-Ga50Au10In40 alloys
  18. CFD simulation of particulate flow in a spiral concentrator
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 9.11.2025 von https://www.degruyterbrill.com/document/doi/10.3139/120.110776/html?lang=de
Button zum nach oben scrollen