Shot Peening Induced Plastic Deformation in Cast Iron – Influence of Graphite Morphology*
-
M. Lundberg
Abstract
Graphite morphology in cast iron strongly affects the mechanical properties such as: Young's modulus, tensile/compressive strength and cyclic mechanical behaviour. In this study, pearlitic compact graphite iron (CGI) and grey cast iron (GI) have been studied in a scanning electron microscope (SEM) before and after shot peening under different conditions. The plastic deformation behaviour of CGI and GI under different shot peening conditions has been analysed using electron backscattering diffraction (EBSD) and electron contrast channelling imaging (ECCI). EBSD and ECCI revealed that plastic deformation around graphite inclusions depends on the size and shape of the graphite. The different response of CGI and GI to shot peening is explained by the different damping properties of the graphite and the matrix capability for plastic deformation. n
Kurzfassung
Die Graphitmorphologie in Gusseisen hat einen starken Einfluss auf die mechanischen Eigenschaften wie E-Modul, Zug- und Druckfestigkeit und das Verhalten unter zyklischer Belastung. Für diese Arbeit wurden Proben aus Grauguss und Vermiculargraphitguss vor und nach einer Kugelstrahlbehandlung mit unterschiedlichen Parametern im Rasterelektronenmikroskop untersucht. Die plastische Verformung wurde mittels EBSD und ECCI analysiert. Dabei zeigt sich, dass die plastische Verformung in der Umgebung von Graphiteinschlüssen von Form und Größe der Einschlüsse abhängt. Die unterschiedlichen Effekte in Grauguss und Vermiculargraphitguss lassen sich mit den verschiedenen Dämpfungseigenschaften der jeweiligen Graphite und der Duktilität der Matrix erklären. n
References
1. Stefanesu, D. M.: Science and Engineering of Casting Solidification. 2nd Ed., Springer, New York, 2009, 10.1007/b135947Suche in Google Scholar
2. Walton, C. F.: Gray and Ductile Iron Castings Handbook. Gray and Ductile Iron Founders’ Society, London, UK, 1971Suche in Google Scholar
3. Davis, J. R.: ASM Specialty Handbook: Cast Irons. ASM Int., Russell Township, Geauga County, Ohio, USA, 1996Suche in Google Scholar
4. Shao, S.; Dawson, S.; Lampic, M.: The mechanical and physical properties of compacted graphite iron. Mat. Sci. Eng. Techn.29 (1998) 8, pp. 397–411, 10.1002/mawe.19980290805Suche in Google Scholar
5. Adams, R. D.: The damping characteristics of certain steels, cast irons and other metals. J. Sound Vibr.23 (1972), pp. 199–216, 10.1016/0022-460x(72)90560-3Suche in Google Scholar
6. Dryden, J. R.; Purdy, G. R.: The effect of graphite on the mechanical properties of cast irons. Acta Metall.37 (1989), pp. 1999–2006, 10.1016/0001-6160(89)90084-9Suche in Google Scholar
7. Ebenau, A.; Löhe, D.; Vöhringer, O.; Macherauch, E.: Influence of shot peening on the microstructure and the bending fatigue strength of bainitic-austenitic nodular cast iron. Proc. 4th Int. Conf. on Shot Peening, ICSP4, Tokyo, Japan, 1990, pp. 389–398Suche in Google Scholar
8. Kirk, D.; Birch, D. G.: Residual stresses induced by peening austenitic ductile cast-iron. Proc. 7th Int. Conf. on Shot Peening, ICSP7, Warsaw, Poland, 1999, pp. 23–32Suche in Google Scholar
9. Lundberg, M.; Peng, R. L.; Ahmad, M.; Bäckström, D.; Vuoristo, T.; Johansson, S.: Influence of Shot Peening Parameters on Residual Stresses in Flake and Vermicular Cast Irons. Mater. Sci. Forum768–769 (2013), pp. 534–541, 10.4028/www.scientific.net/msf.768-769.534Suche in Google Scholar
10. Lundberg, M.; Peng, R. L.; Ahmad, M.; Bäckström, D.; Vuoristo, T.; Johansson, S.: Graphite Morphology's Influence on Shot Peening Results in Cast Iron. Mater. Sci. Forum768–769 (2013), pp. 542–549, 10.4028/www.scientific.net/msf.768-769.542Suche in Google Scholar
© 2014, Carl Hanser Verlag, München
Artikel in diesem Heft
- Veranstaltungen/Events
- Veranstaltungen in Zusammenarbeit mit der AWT
- HTM-Praxis
- HTM-Praxis
- Kurzfassungen/Abstracts
- Kurzfassungen
- Inhalt/Contents
- Inhalt
- Fachbeiträge/Technical Contributions
- Preface
- Residual Stress in the Cementite Phase of Cold Drawn Pearlite*
- Residual Stress Analysis of Thick Film Systems by the Incremental Hole-Drilling Method*
- Stress Build-Up during Multilayer Welding with Novel Martensitic Filler Materials*
- Characterization of Residual Stress Evolved in Iron-Based Shape Memory Alloys*
- Microstructure and Properties of Pearlitic Steel during Cold Wire Drawing: A Residual Stress Perspective*
- Shot Peening Induced Plastic Deformation in Cast Iron – Influence of Graphite Morphology*
- Heat Treatment Effects of Laser Cladded 12 Ni Maraging Tool Steel with Ni-Co-Mo Alloys*
Artikel in diesem Heft
- Veranstaltungen/Events
- Veranstaltungen in Zusammenarbeit mit der AWT
- HTM-Praxis
- HTM-Praxis
- Kurzfassungen/Abstracts
- Kurzfassungen
- Inhalt/Contents
- Inhalt
- Fachbeiträge/Technical Contributions
- Preface
- Residual Stress in the Cementite Phase of Cold Drawn Pearlite*
- Residual Stress Analysis of Thick Film Systems by the Incremental Hole-Drilling Method*
- Stress Build-Up during Multilayer Welding with Novel Martensitic Filler Materials*
- Characterization of Residual Stress Evolved in Iron-Based Shape Memory Alloys*
- Microstructure and Properties of Pearlitic Steel during Cold Wire Drawing: A Residual Stress Perspective*
- Shot Peening Induced Plastic Deformation in Cast Iron – Influence of Graphite Morphology*
- Heat Treatment Effects of Laser Cladded 12 Ni Maraging Tool Steel with Ni-Co-Mo Alloys*
