Fe2B layer growth kinetics on ASTM A307 steel evaluated by two diffusion models

Martin Ortiz-Domínguez; Mourad Keddam

doi:10.1515/mt-2023-0306

Artikel

Fe₂B layer growth kinetics on ASTM A307 steel evaluated by two diffusion models

Martin Ortiz-Domínguez
Asst. Prof. Dt. Dr. Martin Ortiz-Domínguez is a full time researcher and lecturer at the Escuela Superior de Ciudad Sahagún-UAEH. He is a Mechanical Engineer with a specific interest in quantum information theory, nanotechnology, classical electrodynamics, surface engineering, tribology and processes that occur at interfaces as well as mechanical behavior of metallic materials. His PhD in Mechanical Engineering is from National Polytechnic Institute, Mexico in 2013.
und Mourad Keddam
Prof. Dr. Mourad Keddam, born 1965, completed his graduate and doctorate studies at National Polytechnic School (El-Harrach, Algiers, Algeria). He works in thermochemical treatments and modeling of their kinetics and metallurgical phase transformations. He has published over 150 publications in the field of boriding and nitriding. He has been working in the Department of Materials Sciences at the university of Sciences and Technology Houari Boumediene (Algiers, Algeria) since 2001. He is currently full professor at the same institution.

Veröffentlicht/Copyright: 23. Januar 2024

Veröffentlicht von

Veröffentlichen auch Sie bei De Gruyter Brill

Manuskript einreichen Informationen für Autor*innen

Aus der Zeitschrift Materials Testing Band 66 Heft 3

Abstract

In this study, we implemented two simple models to simulate the growth of the Fe₂B layer on ASTM A307 steel through boriding. The first model considered steady-state boron diffusion, while the second model incorporated transient regime effects. In the steady-state model, the boron concentration profile within the Fe₂B layer exhibited linearity. By correlating the boron chemical potential with the inward mass flux at the (Fe₂B/substrate) interface, we confirmed the parabolic nature of layer growth. Both models were employed to determine the boron activation energies, yielding the same value of approximately 164 kJ mol⁻¹. Experimental validation of the two models was conducted under two additional boriding conditions (1323 K for 1.5 and 2 h). Finally, the simulated layer thicknesses matched with the experimental values.

Keywords: boriding; iron boride; kinetics; activation energies; diffusion models

Corresponding author: Mourad Keddam, SDM, USTHB, B.P. 32 El Alia Bab Ezzouar, Algiers, 16000, Algeria, E-mail: keddam@yahoo.fr

Funding source: PRODEP and CONAHCyT

About the authors

Martin Ortiz-Domínguez

Asst. Prof. Dt. Dr. Martin Ortiz-Domínguez is a full time researcher and lecturer at the Escuela Superior de Ciudad Sahagún-UAEH. He is a Mechanical Engineer with a specific interest in quantum information theory, nanotechnology, classical electrodynamics, surface engineering, tribology and processes that occur at interfaces as well as mechanical behavior of metallic materials. His PhD in Mechanical Engineering is from National Polytechnic Institute, Mexico in 2013.

Mourad Keddam

Prof. Dr. Mourad Keddam, born 1965, completed his graduate and doctorate studies at National Polytechnic School (El-Harrach, Algiers, Algeria). He works in thermochemical treatments and modeling of their kinetics and metallurgical phase transformations. He has published over 150 publications in the field of boriding and nitriding. He has been working in the Department of Materials Sciences at the university of Sciences and Technology Houari Boumediene (Algiers, Algeria) since 2001. He is currently full professor at the same institution.

Research ethics: Not applicable.
Author contributions: The authors have accepted responsibility for the entire content of this manuscript and approved its submission.
Competing interests: The authors state no conflict of interest.
Research funding: The work described in this paper was supported by a grant of PRODEP and CONAHCyT México (National Council of Humanities, Science and Technology).
Data availability: Not applicable.

References

[1] M. Kulka, “Trends in thermochemical techniques of boriding,” in Current Trends in Boriding, Engineering Materials, Cham, Switzerland, Springer, 2019, pp. 17–98.10.1007/978-3-030-06782-3_4Suche in Google Scholar

[2] N. Koga, K. Tanahara, and O. Umezawa, “Deformation structure around a crack in γ′-Fe4N layer of nitrided extra-low-carbon steel subjected to cyclic tensile test,” Metall. Mater. Trans. A, vol. 53, pp. 1150–1155, 2022, https://doi.org/10.1007/s11661-022-06607-3.Suche in Google Scholar

[3] M. Belaid, M. L. Fares, O. Assalla, and F. Boukari, “Surface characterization of a modified cold work tool steel treated by powder-pack boronizing,” Materwiss Werksttech, vol. 53, no. 1, pp. 15–38, 2022, https://doi.org/10.1002/mawe.202100117.Suche in Google Scholar

[4] I. Türkmen and E. Yalamaç, “Effect of alternative boronizing mixtures on boride layer and tribological behaviour of boronized SAE 1020 steel,” Metal Mater. Int., vol. 28, pp. 1114–1128, 2022, https://doi.org/10.1007/s12540-021-00987-8.Suche in Google Scholar

[5] E. A. Smol’nikov and L. M. Sarmanova, “Study of the possibility of liquid boriding of high-speed steels,” Met. Sci. Heat Treat., vol. 24, pp. 785–788, 1982, https://doi.org/10.1007/BF00774735.Suche in Google Scholar

[6] M. Kulka, N. Makuch, and A. Piasecki, “Nanomechanical characterization and fracture toughness of FeB and Fe2B iron borides produced by gas boriding of Armco iron,” Surf. Coat. Technol., vol. 325, pp. 515–532, 2017, https://doi.org/10.1016/j.surfcoat.2017.07.020.Suche in Google Scholar

[7] K. Sikorski, T. Wierzchoń, and P. Bieliński, “X-ray microanalysis and properties of multicomponent plasma-borided layers on steels,” J. Mater. Sci., vol. 33, pp. 811–815, 1998, https://doi.org/10.1023/A:1004322719560.10.1023/A:1004322719560Suche in Google Scholar

[8] I. Gunes, S. Ulker, and S. Taktak, “Kinetics of plasma paste boronized AISI 8620 steel in borax paste mixtures,” Protect. Met. Phys. Chem., vol. 49, pp. 567–573, 2013, https://doi.org/10.1134/S2070205113050122.Suche in Google Scholar

[9] V. Jain and G. Sundararajan, “Influence of the pack thickness of the boronizing mixture on the boriding of steel,” Surf. Coat. Technol., vol. 149, pp. 21–26, 2002, https://doi.org/10.1016/S0257-8972(01)01385-8.Suche in Google Scholar

[10] M. Ortiz-Domínguez, et al.., “Estimation of Fe2B growth on low-carbon steel based on two diffusion models,” Int. J. Mater. Res., vol. 102, no. 4, pp. 429–434, 2011, https://doi.org/10.3139/146.110491.Suche in Google Scholar

[11] I. Campos-Silva, M. Ortiz-Domínguez, C. VillaVelázquez, R. Escobar, and N. López, “Growth kinetics of boride layers: a modified approach,” Defect Diffusion Forum, vol. 272, pp. 79–86, 2007, https://doi.org/10.4028/www.scientific.net/DDF.272.79.Suche in Google Scholar

[12] M. Arslan-Kaba, M. Karimzadehkhoei, M. Keddam, S. Timur, and G. Kartal Sireli, “An experimental and modelling study on pulse current integrated CRTD-Bor process,” Mater. Chem. Phys., vol. 302, 2023, Art. no. 127735, https://doi.org/10.1016/j.matchemphys.2023.127735.Suche in Google Scholar

[13] I. Morgado-González, M. Ortiz-Dominguez, and M. Keddam, “Characterization of Fe2B layers on ASTM A1011 steel and modelling of boron diffusion,” Mater. Test., vol. 64, no. 1, pp. 55–66, 2022, https://doi.org/10.1515/mt-2021-2007.Suche in Google Scholar

[14] R. D. Ramdan, T. Takaki, K. Yashiro, and Y. Tomita, “The effects of structure orientation on the growth of Fe2B boride by multi-phase-field simulation,” Mater. Trans., vol. 51, no. 1, pp. 62–67, 2010, https://doi.org/10.2320/matertrans.M2009227.Suche in Google Scholar

[15] I. Campos, M. Islas, E. González, P. Ponce, and G. Ramírez, “Use of fuzzy logic for modeling the growth of Fe2B boride layers during boronizing,” Surf. Coating. Technol., vol. 201, no. 6, pp. 2717–2723, 2006, https://doi.org/10.1016/j.surfcoat.2006.05.016.Suche in Google Scholar

[16] I. Campos, J. Oseguera, U. Figueroa, J. A. Garcı́a, O. Bautista, and G. Kelemenis, “Kinetic study of boron diffusion in the paste-boriding process,” Mater. Sci. Eng., A, vol. 352, no. 1–2, pp. 261–265, 2003, https://doi.org/10.1016/S0921-5093(02)00910-3.Suche in Google Scholar

[17] M. Ortiz-Dominguez, et al.., “Modeling of the growth kinetics of boride layers in powder-pack borided ASTM A36 steel based on two different approaches,” Adv. Mater. Sci. Eng., vol. 2019, 2019, Art. no. 5985617, https://doi.org/10.1155/2019/5985617.Suche in Google Scholar

[18] C. M. Brakman, A. W. J. Gommers, and E. J. Mittemeijer, “Boriding of Fe and Fe–C, Fe–Cr, and Fe–Ni alloys; Boride-layer growth kinetics,” J. Mater. Sci., vol. 4, pp. 1354–1370, 1998, https://doi.org/10.1557/JMR.1989.1354.Suche in Google Scholar

[19] H. Okamoto, “B–Fe (boron–iron),” J. Phase Equilib. Diffus., vol. 25, pp. 297–298, 2004, https://doi.org/10.1007/s11669-004-0128-3.Suche in Google Scholar

[20] L. G. Yu, X. J. Chen, A. K. Khor, and G. Sundararajan, “FeB/Fe2B phase transformation during SPS pack-boriding: boride layer growth kinetics,” Acta Mater., vol. 53, no. 8, pp. 2361–2368, 2005, https://doi.org/10.1016/j.actamat.2005.01.043.Suche in Google Scholar

[21] W. H. Press, B. P. Flannery, and S. A. Teukolsky, Numerical Recipes in Pascal: The Art of Scientific Computing, Cambridge, UK, Cambridge University Press, 1989.Suche in Google Scholar

[22] H. Kunst and O. Schaaber, “Beobachtungen beim oberflaechenborieren von Stahl,” Haerterei Technische Mitteilungen, vol. 22, no. 1, pp. 1–25, 1967, https://doi.org/10.1007/978-3-642-52224-6_7.Suche in Google Scholar

[23] İ. Türkmen, E. Yalamaç, and M. Keddam, “Investigation of tribological behaviour and diffusion model of Fe2B layer formed by pack-boriding on SAE 1020 steel,” Surf. Coating. Technol., vol. 377, 2019, Art. no. 124888, https://doi.org/10.1016/j.surfcoat.2019.08.017.Suche in Google Scholar

[24] C. I. VillaVelázquez-Mendoza, et al.., “Effect of substrate roughness, time and temperature on the processing of iron boride coatings: experimental and statistical approaches,” Int. J. Surf. Sci. Eng., vol. 8, no. 1, pp. 71–91, 2014, https://doi.org/10.1504/IJSURFSE.2014.059315.Suche in Google Scholar

[25] G. Palombarini and M. Carbucicchio, “Growth of boride coatings on iron,” J. Mater. Sci. Lett., vol. 6, pp. 415–416, 1987, https://doi.org/10.1007/BF01756781.Suche in Google Scholar

[26] Y. Jiang, Y. Bao, and M. Wang, “Kinetic analysis of additive on plasma electrolytic boriding,” Coatings, vol. 7, no. 5, 2017, Art. no. 61, https://doi.org/10.3390/coatings7050061.Suche in Google Scholar

[27] G. Kartal, O. L. Eryilmaz, G. Krumdick, A. Erdemir, and S. Timur, “Kinetics of electrochemical boriding of low carbon steel,” Appl. Surf. Sci., vol. 257, no. 15, pp. 6928–6934, 2011, https://doi.org/10.1016/j.apsusc.2011.03.034.Suche in Google Scholar

[28] S. Sen, U. Sen, and C. Bindal, “An approach to kinetic study of borided steels,” Surf. Coat. Technol., vol. 191, no. 1–2, pp. 274–285, 2005, https://doi.org/10.1016/j.surfcoat.2004.03.040.Suche in Google Scholar

[29] M. Arslan, O. Kagan Coskun, M. Karimzadehkhoei, G. Kartal Sireli, and S. Timur, “Evaluation of pulse current integrated CRTD-Bor for boron diffusion in low carbon steel,” Mater. Lett., vol. 3081, 2022, Art. no. 131299, https://doi.org/10.1016/j.matlet.2021.131299.Suche in Google Scholar

[30] R. Hasan, J. Zhong Li Liew, and N. Ab Halim, “The effect of groove shape on activation energy of powder pack boronizing in mild steel,” J. Tribol., vol. 22, pp. 123–137, 2019, https://jurnaltribologi.mytribos.org/v22/JT-22-123-137.pdf.Suche in Google Scholar

[31] Z. G. Su, X. X. Lv, J. An, Y. Yang, and S. Sun, “Role of RE element Nd on boronizing kinetics of steels,” J. Mater. Eng. Perform., vol. 21, pp. 1337–1345, 2012, https://doi.org/10.1007/s11665-011-0053-7.Suche in Google Scholar

[32] E. Hernández-Sánchez and J. C. Velázquez, “Kinetics of growth of iron boride layers on a low-carbon steel surface,” Lab. Unit Oper. Exp. Methods Chem. Eng., 2018, https://doi.org/10.5772/intechopen.73592.Suche in Google Scholar

[33] P. A. Ruiz-Trabolsi, et al.., “Kinetics of the boride layers obtained on AISI 1018 steel by considering the amount of matter involved,” Coatings, vol. 11, no. 2, p. 259, 2021, https://doi.org/10.3390/coatings11020259.Suche in Google Scholar

[34] M. Ortiz-Domínguez and M. Keddam, “Modelling boron diffusion for Fe2B layer formation: comparative kinetics analysis in pack-boronized AISI 4147 steel,” Mater. Test., vol. 65, no. 10, pp. 1539–1550, 2023, https://doi.org/10.1515/mt-2023-0214.Suche in Google Scholar

Published Online: 2024-01-23

Published in Print: 2024-03-25

Sie haben derzeit keinen Zugang zu diesem Inhalt.

Artikel in diesem Heft

https://doi.org/10.1515/mt-2023-0306

Schlagwörter für diesen Artikel

boriding; iron boride; kinetics; activation energies; diffusion models