Startseite Effect of thermomechanical processing on the mechanical properties of CuZn10 alloy
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Effect of thermomechanical processing on the mechanical properties of CuZn10 alloy

  • S. Osman Yilmaz , Tanju Teker EMAIL logo , Yaşar Onur Batmaz

    Yaşar Onur Batmaz, born in 1992, works as a manufacturing engineer in Kayalar Copper Alloys, Industry and Trade Incorporated Company, Ergene, Tekirdag, Turkey. He graduated from the Department of Metallurgy and Material Engineering, University of Yıldız Technical University, İstanbul, Turkey, in 2016. His research interests are casting and heat treatments.

    und Çağlar Yüksel

    Çağlar Yüksel, born in 1984, works in the University of Atatürk, Faculty of Engineering, Department of Metallurgy and Material Engineering, Erzurum, Turkey. He graduated in Metallurgy and Material Engineering from the Yıldız Technical University, İstanbul, Turkey, in 2008. He received his M.Sc. and Ph.D. degrees from the Yıldız Technical University, İstanbul, Turkey, in 2011 and 2016, respectively. His research study interests casting techniques, casting of magnesium alloys, casting of aluminum alloys, and composite materials.

    ORCID logo
Veröffentlicht/Copyright: 7. Juli 2022
Veröffentlichen auch Sie bei De Gruyter Brill

Abstract

The effects of thermomechanical processing on the grain size, tensile strength, and strain rate of a CuZn10 alloy were investigated. Microstructures of thermomechanically treated samples were introduced using a scanning electron microscope. The relationships between the flow stress, reduction ratio, annealing temperatures, and strain rates were detected for determination of activation energies and optimized thermomechanical parameters. The effect of grain size on the mechanical properties was examined by tensile and microhardness tests. The typical fractographs of samples after tensile tests were examined using a scanning electron microscope. It was observed that the annealing temperature and aging time have significant effects on the optimum grain size. Mechanical properties of the thermomechanically treated samples were improved by strain rate, deformation ratio, annealing temperature, and aging time.


Corresponding author: Tanju Teker, Sivas Cumhuriyet University, Faculty of Technology, Department of Manufacturing Engineering, 58140, Sivas, Turkey, E-mail:

About the authors

Yaşar Onur Batmaz

Yaşar Onur Batmaz, born in 1992, works as a manufacturing engineer in Kayalar Copper Alloys, Industry and Trade Incorporated Company, Ergene, Tekirdag, Turkey. He graduated from the Department of Metallurgy and Material Engineering, University of Yıldız Technical University, İstanbul, Turkey, in 2016. His research interests are casting and heat treatments.

Çağlar Yüksel

Çağlar Yüksel, born in 1984, works in the University of Atatürk, Faculty of Engineering, Department of Metallurgy and Material Engineering, Erzurum, Turkey. He graduated in Metallurgy and Material Engineering from the Yıldız Technical University, İstanbul, Turkey, in 2008. He received his M.Sc. and Ph.D. degrees from the Yıldız Technical University, İstanbul, Turkey, in 2011 and 2016, respectively. His research study interests casting techniques, casting of magnesium alloys, casting of aluminum alloys, and composite materials.

Acknowledgments

The authors are grateful to KAYALAR copper industry and trade incorporated company for their assistance in conducting the experiments.

  1. Author contributions: All the authors have accepted responsibility for the entire content of this submitted manuscript and approved submission.

  2. Research funding: None declared.

  3. Conflict of interest statement: The authors declare no conflicts of interest regarding this article.

  4. Disclosure statement: No potential conflict of interest was reported by the authors.

References

[1] S. Nestorovic, D. Markovic, and I. Markovic, “Influence of thermal cycling treatment on the anneal hardening effect of Cu-10Zn alloy,” J. Alloys Compd., vol. 489, no. 2, pp. 582–585, 2010, https://doi.org/10.1016/j.jallcom.2009.09.115.Suche in Google Scholar

[2] W. Chen, M. Wang, Z. Li et al.., “A novel Cu-10Zn-1.5Ni-0.34Si alloy with excellent mechanical property through precipitation hardening,” J. Mater. Eng. Perform., vol. 25, pp. 4624–4630, 2016, https://doi.org/10.1007/s11665-016-2354-3.Suche in Google Scholar

[3] S. Zhang, H. Zhu, Z. Hu, X. Zeng, and F. Zhong, “Selective laser melting of Cu-10Zn alloy powder using high laser power,” Powder Technol., vol. 342, pp. 613–620, 2019, https://doi.org/10.1016/j.powtec.2018.10.002.Suche in Google Scholar

[4] Q. Liu and L. Cheng, “Structural evolution and electronic properties of Cu-Zn alloy clusters,” J. Alloys Compd., vol. 771, pp. 762–768, 2019, https://doi.org/10.1016/j.jallcom.2018.08.033.Suche in Google Scholar

[5] L. Cai, X. Jiang, Y. Guo et al.., “Friction and wear performance of a copper-based bond emery wheel for rail grinding,” Mater. Test., vol. 62, no. 12, pp. 1205–1214, 2020, https://doi.org/10.3139/120.111594.Suche in Google Scholar

[6] T. Watanabe, S. Tsurekawa, X. Zhao, L. Zuo, and C. Esling, “A new challenge: grain boundary engineering for advanced materials by magnetic field application,” J. Mater. Sci., vol. 41, pp. 7747–7759, 2006, https://doi.org/10.1007/s10853-006-0740-1.Suche in Google Scholar

[7] A. Das, “Grain boundary engineering: fatigue fracture,” Phil. Mag., vol. 97, no. 11, pp. 867–916, 2017, https://doi.org/10.1080/14786435.2017.1285072.Suche in Google Scholar

[8] A. Telang, A. S. Gill, M. Kumar et al.., “Iterative thermomechanical processing of alloy 600 for improved resistance to corrosion and stress corrosion cracking,” Acta Mater., vol. 113, pp. 180–193, 2016, https://doi.org/10.1016/j.actamat.2016.05.009.Suche in Google Scholar

[9] C. K. Kaithwas, P. Bhuyan, S. K. Pradhan, and S. Mandal, “Microstructure evolution during low-strain thermo-mechanical processing and its repercussion on intergranular corrosion in alloy 600H,” Mater. Charact., vol. 145, pp. 582–593, 2018, https://doi.org/10.1016/j.matchar.2018.09.019.Suche in Google Scholar

[10] D. L. Engelberg, R. C. Newman, and T. J. Marrow, “Effect of thermomechanical process history on grain boundary control in an austenitic stainless steel,” Scr. Mater., vol. 59, no. 5, pp. 554–557, 2008, https://doi.org/10.1016/j.scriptamat.2008.05.012.Suche in Google Scholar

[11] A. Telang, A. S. Gill, K. Zweiacker, C. Liu, J. M. Wiezorek, and V. K. Vasudevan, “Effect of thermo-mechanical processing on sensitization and corrosion in alloy 600 studied by SEM-and TEM-based diffraction and orientation imaging techniques,” J. Nucl. Mater., vol. 505, pp. 276–288, 2018, https://doi.org/10.1016/j.jnucmat.2017.07.053.Suche in Google Scholar

[12] M. Kumar, W. E. King, and A. J. Schwartz, “Modifications to the microstructural topology in f.c.c. materials through thermomechanical processing,” Acta Mater., vol. 48, no. 9, pp. 2081–2091, 2000, https://doi.org/10.1016/S1359-6454(00)00045-8.Suche in Google Scholar

[13] C. Cayron, “Quantification of multiple twinning in face centred cubic materials,” Acta Mater., vol. 59, no. 1, pp. 252–262, 2011, https://doi.org/10.1016/j.actamat.2010.09.029.Suche in Google Scholar

[14] V. Randle, “Twinning-related grain boundary engineering,” Acta Mater., vol. 52, no. 14, pp. 4067–4081, 2004, https://doi.org/10.1016/j.actamat.2004.05.031.Suche in Google Scholar

[15] S. Tokita, H. Kokawa, Y. S. Sato, and H. T. Fujii, “In situ EBSD observation of grain boundary character distribution evolution during thermomechanical process used for grain boundary engineering of 304 austenitic stainless steel,” Mater. Charact., vol. 131, pp. 31–38, 2017, https://doi.org/10.1016/j.matchar.2017.06.032.Suche in Google Scholar

[16] M. Kumar, A. J. Schwartz, W. E. King, “Microstructural evolution during grain boundary engineering of low to medium stacking fault energy fcc materials,” Acta Mater., vol. 50, no. 10, pp. 2599–2612, 2002, https://doi.org/10.1016/S1359-6454(02)00090-3.Suche in Google Scholar

[17] C. Zener, J. H. Hollomon, “Effect of strain-rate upon the plastic flow of steel,” J. Appl. Phys., vol. 15, no. 1, pp. 22–27, 1944, https://doi.org/10.1063/1.1707363.Suche in Google Scholar

[18] C. A. Schuh, M. Kumar, W. E. King, “Analysis of grain boundary networks and their evolution during grain boundary engineering,” Acta Mater., vol. 51, no. 3, pp. 687–700, 2003, https://doi.org/10.1016/S1359-6454(02)00447-0.Suche in Google Scholar

[19] V. Randle and M. Coleman, “A study of low-strain and medium-strain grain boundary engineering,” Acta Mater., vol. 57, no. 11, pp. 3410–3421, 2009, https://doi.org/10.1016/j.actamat.2009.04.002.Suche in Google Scholar

[20] M. Shimada, H. Kokawa, Z. J. Wang, Y. S. Sato, I. Karibe, “Optimization of grain boundary character distribution for intergranular corrosion resistant 304 stainless steel by twin-induced grain boundary engineering,” Acta Mater., vol. 50, no. 9, pp. 2331–2341, 2002, https://doi.org/10.1016/S1359-6454(02)00064-2.Suche in Google Scholar

Published Online: 2022-07-07
Published in Print: 2022-07-26

© 2022 Walter de Gruyter GmbH, Berlin/Boston

Heruntergeladen am 14.9.2025 von https://www.degruyterbrill.com/document/doi/10.1515/mt-2021-2197/html
Button zum nach oben scrollen