Startseite Technik An investigation of multistream plate-fin heat exchanger modelling and design: a review
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

An investigation of multistream plate-fin heat exchanger modelling and design: a review

  • Nazar Oudah Mousa Alyaseen , Salem Mehrzad EMAIL logo und Mohammad Reza Saffarian
Veröffentlicht/Copyright: 2. Juni 2023
Veröffentlichen auch Sie bei De Gruyter Brill
Manuskript einreichen Informationen für Autor*innen
Kerntechnik
Aus der Zeitschrift Kerntechnik Band 88 Heft 4

Abstract

In line with population expansion and industrial development, the world’s energy consumption has been rising gradually over the past three decades. As a result, methods for energy conservation have been sought. One of the most common strategies is heat recovery, which is efficient and cost-effective to the extent possible. Heat recovery is not just about saving energy for primary consumption; it is also about lowering emissions and protecting the environment. In this respect, one of the most important strategies for heat recovery is to develop heat exchangers and exploit the energy associated with many of the processes’ output products in order to use it in new processes. Many researchers working in the field of heat engineering are now looking into novel heat transfer techniques. Use of the heat exchanger as a compact is one of these ways that might be considered. The current review therefore concentrates on the design of plate-fin heat exchangers (PFHE) and multi-stream plate-fin heat exchangers (MSPFHE) based on various models. The current review offers some suggestions for upcoming studies on improving heat transfer and minimizing power use.

Keywords: design; heat exchanger; heat transfer; multi-stream plate-fin heat exchanger (MSPFHE); plate-fin heat exchanger (PFHE)
Corresponding author: Salem Mehrzad, Department of Mechanical Engineering, Faculty of Engineering, Shahid Chamran University of Ahvaz, Ahvaz, 83151-61355, Iran, E-mail:

  1. Author contributions: All the authors have accepted responsibility for the entire content of this submitted manuscript and approved submission.

  2. Research funding: None declared.

  3. Conflict of interest statement: The authors declare no conflicts of interest regarding this article.

References

Ahn, J., Kim, M.S., and Jang, S. (2018). Effects of cross-sectional aspect ratio of V-shaped ribs and blockage ratio on heat transfer in a channel at a low Reynolds number. J. Mech. Sci. Technol. 32: 5465–5473, https://doi.org/10.1007/s12206-018-1044-5.Suche in Google Scholar

Ajeel, R.K., Saiful-Islam, W., Sopian, K., and Yusoff, M.Z. (2020a). Analysis of thermal-hydraulic performance and flow structures of nanofluids across various corrugated channels: an experimental and numerical study. Therm. Sci. Eng. Prog. 19: 100604, https://doi.org/10.1016/j.tsep.2020.100604.Suche in Google Scholar

Ajeel, R.K., Salim, W.I., and Hasnan, K. (2018). Thermal and hydraulic characteristics of turbulent nanofluids flow in trapezoidal-corrugated channel: symmetry and zigzag shaped. Case Stud. Therm. Eng. 12: 620–635, https://doi.org/10.1016/j.csite.2018.08.002.Suche in Google Scholar

Ajeel, R.K., Salim, W.I., and Hasnan, K. (2019a). Design characteristics of symmetrical semicircle-corrugated channel on heat transfer enhancement with nanofluid. Int. J. Mech. Sci. 151: 236–250, https://doi.org/10.1016/j.ijmecsci.2018.11.022.Suche in Google Scholar

Ajeel, R.K., Salim, W.I., and Hasnan, K. (2019b). Experimental and numerical investigations of convection heat transfer in corrugated channels using alumina nanofluid under a turbulent flow regime. Chem. Eng. Res. Des. 148: 202–217, https://doi.org/10.1016/j.cherd.2019.06.003.Suche in Google Scholar

Ajeel, R.K., Salim, W.I., and Hasnan, K. (2019c). Thermal performance comparison of various corrugated channels using nanofluid: numerical study. Alex. Eng. J. 58: 75–87, https://doi.org/10.1016/j.aej.2018.12.009.Suche in Google Scholar

Ajeel, R.K., Salim, W.I., and Hasnan, K. (2020b). Numerical investigations of heat transfer enhancement in a house shaped-corrugated channel: combination of nanofluid and geometrical parameters. Therm. Sci. Eng. Prog. 17: 100376, https://doi.org/10.1016/j.tsep.2019.100376.Suche in Google Scholar

Ajeel, R.K., Salim, W.I., Sopian, K., Yusoff, M.Z., Hasnan, K., Ibrahim, A., and Al-Waeli, A.H. (2019d). Turbulent convective heat transfer of silica oxide nanofluid through corrugated channels: an experimental and numerical study. Int. J. Heat Mass Tran. 145: 118806, https://doi.org/10.1016/j.ijheatmasstransfer.2019.118806.Suche in Google Scholar

Ajeel, R.K., Salim, W.S.I.W., and Hasnan, K. (2019e). Heat transfer enhancement in semicircle corrugated channel: effect of geometrical parameters and nanofluid. J. Adv. Res. Fluid Mech. Therm. Sci. 53: 82–94.Suche in Google Scholar

Ajeel, R.K., Sopian, K., and Zulkifli, R. (2021a). A novel curved-corrugated channel model: thermal-hydraulic performance and design parameters with nanofluid. Int. Commun. Heat Mass Tran. 120: 105037, https://doi.org/10.1016/j.icheatmasstransfer.2020.105037.Suche in Google Scholar

Ajeel, R.K., Sopian, K., and Zulkifli, R. (2021b). Thermal-hydraulic performance and design parameters in a curved-corrugated channel with L-shaped baffles and nanofluid. J. Energy Storage 34: 101996, https://doi.org/10.1016/j.est.2020.101996.Suche in Google Scholar

Ajeel, R.K., Sopian, K., Zulkifli, R., Fayyadh, S.N., and Hilo, A.K. (2021c). Assessment and analysis of binary hybrid nanofluid impact on new configurations for curved-corrugated channel. Adv. Powder Technol. 32: 3869–3884, https://doi.org/10.1016/j.apt.2021.08.041.Suche in Google Scholar

Ajeel, R.K., Zulkifli, R., Sopian, K., Fayyadh, S.N., Fazlizan, A., and Ibrahim, A. (2021d). Numerical investigation of binary hybrid nanofluid in new configurations for curved-corrugated channel by thermal-hydraulic performance method. Powder Technol. 385: 144–159, https://doi.org/10.1016/j.powtec.2021.02.055.Suche in Google Scholar

Ajour, M.N., Daqrouq, K.O., and Karimipour, A. (2022). Lithium-ion batteries investigation regarding different fins distribution associated electrochemical effects and various voltage types. J. Energy Storage 51: 104383, https://doi.org/10.1016/j.est.2022.104383.Suche in Google Scholar

Alnak, D.E. (2020). Thermohydraulic performance study of different square baffle angles in cross-corrugated channel. J. Energy Storage 28: 101295, https://doi.org/10.1016/j.est.2020.101295.Suche in Google Scholar

Bhuiyan, A.A. and Islam, A.S. (2016). Thermal and hydraulic performance of finned-tube heat exchangers under different flow ranges: a review on modeling and experiment. Int. J. Heat Mass Tran. 101: 38–59, https://doi.org/10.1016/j.ijheatmasstransfer.2016.05.022.Suche in Google Scholar

Boukhadia, K., Ameur, H., Sahel, D., and Bozit, M. (2018). Effect of the perforation design on the fluid flow and heat transfer characteristics of a plate fin heat exchanger. Int. J. Therm. Sci. 126: 172–180, https://doi.org/10.1016/j.ijthermalsci.2017.12.025.Suche in Google Scholar

Buyruk, E. and Karabulut, K. (2018). Enhancement of heat transfer for plate fin heat exchangers considering the effects of fin arrangements. Heat Tran. Eng. 39: 1392–1404, https://doi.org/10.1080/01457632.2017.1366238.Suche in Google Scholar

Chen, J., Li, K., Liu, C., Li, M., Lv, Y., Jia, L., and Jiang, S. (2017). Enhanced efficiency of thermoelectric generator by optimizing mechanical and electrical structures. Energies 10: 1329, https://doi.org/10.3390/en10091329.Suche in Google Scholar

Comamala, M., Cózar, I.R., Massaguer, A., Massaguer, E., and Pujol, T. (2018). Effects of design parameters on fuel economy and output power in an automotive thermoelectric generator. Energies 11: 3274, https://doi.org/10.3390/en11123274.Suche in Google Scholar

Dang, W., Nugud, J., Lin, Z.M., Zhang, Y.H., Liu, S., and Wang, L.B. (2018). The performances of circular tube bank fin heat exchangers with fins punched with quadrilateral vortex generators and flow re-distributors. Appl. Therm. Eng. 134: 437–449, https://doi.org/10.1016/j.applthermaleng.2018.02.008.Suche in Google Scholar

Das, P.K. and Ghosh, I. (2012). Thermal design of multistream plate fin heat exchangers—a state-of-the-art review. Heat Tran. Eng. 33: 284–300, https://doi.org/10.1080/01457632.2012.611451.Suche in Google Scholar

Della Torre, A., Montenegro, G., Onorati, A., Khadilkar, S., and Icarelli, R. (2019). Multi-scale CFD modeling of plate heat exchangers including offset-strip fins and dimple-type turbulators for automotive applications. Energies 12: 2965, https://doi.org/10.3390/en12152965.Suche in Google Scholar

Desai, A.R. (2015). Computational model for steady state simulation of a plate-fin heat exchanger, Doctoral dissertation. Arlington, University of Texas at Arlington.Suche in Google Scholar

Gadalla, M.A. (2015). A new graphical method for Pinch Analysis applications: heat exchanger network retrofit and energy integration. Energy 81: 159–174, https://doi.org/10.1016/j.energy.2014.12.011.Suche in Google Scholar

Gholami, A., Wahid, M.A., and Mohammed, H.A. (2017). Thermal–hydraulic performance of fin-and-oval tube compact heat exchangers with innovative design of corrugated fin patterns. Int. J. Heat Mass Tran. 106: 573–592, https://doi.org/10.1016/j.ijheatmasstransfer.2016.09.028.Suche in Google Scholar

Goyal, M., Chakravarty, A., and Atrey, M.D. (2014). Two dimensional model for multistream plate fin heat exchangers. Cryogenics 61: 70–78, https://doi.org/10.1016/j.cryogenics.2014.02.017.Suche in Google Scholar

Goyal, M., Chakravarty, A., and Atrey, M.D. (2017). Experimental investigations and validation of two dimensional model for multistream plate fin heat exchangers. Cryogenics 82: 83–91, https://doi.org/10.1016/j.cryogenics.2016.12.005.Suche in Google Scholar

Guo, K., Zhang, N., and Smith, R. (2015). Optimisation of fin selection and thermal design of counter-current plate-fin heat exchangers. Appl. Therm. Eng. 78: 491–499, https://doi.org/10.1016/j.applthermaleng.2014.11.071.Suche in Google Scholar

Hajmohammadi, M.R., Doustahadi, A., and Ahmadian-Elmi, M. (2020). Heat transfer enhancement by a circumferentially non-uniform array of longitudinal fins assembled inside a circular channel. Int. J. Heat Mass Tran. 158: 120020, https://doi.org/10.1016/j.ijheatmasstransfer.2020.120020.Suche in Google Scholar

Hamad, A.J. and Ajeel, R.K. (2022). Combined effect of oblique ribs and a nanofluid on the thermal-hydraulic performance of a corrugated channel: numerical study. J. Eng. Phys. Thermophys. 95: 970–978, https://doi.org/10.1007/s10891-022-02552-5.Suche in Google Scholar

Huisseune, H., T’Joen, C., De Jaeger, P., Ameel, B., De Schampheleire, S., and De Paepe, M. (2013). Performance analysis of a compound heat exchanger by screening its design parameters. Appl. Therm. Eng. 51: 490–501, https://doi.org/10.1016/j.applthermaleng.2012.09.044.Suche in Google Scholar

Jiang, Q.F., Zhuang, M., Zhu, Z.G., Zhang, Q.Y., and Sheng, L.H. (2017). Performance evaluation of cryogenic counter-flow heat exchangers with longitudinal conduction, heat in-leak and property variations. IOP Conf. Ser. Mater. Sci. Eng. 278: 012064, https://doi.org/10.1088/1757-899x/278/1/012064.Suche in Google Scholar

Kays, W.M. and London, A.L. (1984). Compact heat exchangers. Department of Energy Office of Scientific and Technical Information, US.Suche in Google Scholar

Kemp, I.C. (2011). Pinch analysis and process integration: a user guide on process integration for the efficient use of energy. Elsevier, UK.Suche in Google Scholar

Khan, T.A. and Li, W. (2017). Optimal design of plate-fin heat exchanger by combining multi-objective algorithms. Int. J. Heat Mass Tran. 108: 1560–1572, https://doi.org/10.1016/j.ijheatmasstransfer.2017.01.031.Suche in Google Scholar

Klemeš, J.J. and Kravanja, Z. (2013). Forty years of heat integration: pinch analysis (PA) and mathematical programming (MP). Curr. Opin. Chem. Eng. 2: 461–474.10.1016/j.coche.2013.10.003Suche in Google Scholar

Klemeš, J.J., Varbanov, P.S., Walmsley, T.G., and Jia, X. (2018). New directions in the implementation of pinch methodology (PM). Renew. Sustain. Energy Rev. 98: 439–468.10.1016/j.rser.2018.09.030Suche in Google Scholar

Kotcioglu, I., Khalaji, M.N., and Cansiz, A. (2018). Heat transfer analysis of a rectangular channel having tubular router in different winglet configurations with Taguchi method. Appl. Therm. Eng. 132: 637–650, https://doi.org/10.1016/j.applthermaleng.2017.12.120.Suche in Google Scholar

Kumar, S., Dinesha, P., and Sai Krishna, K.R.N. (2019). Experimental and numerical analysis of cylindrical turbulators in a double pipe heat exchanger under turbulent flow conditions. J. Turbul. 20: 245–262, https://doi.org/10.1080/14685248.2019.1623405.Suche in Google Scholar

Leachman, J.W., Jacobsen, R.T., Lemmon, E.W., and Penoncello, S.G. (2017). Thermodynamic properties of cryogenic fluids. Springer International Publishing, Cham.10.1007/978-3-319-57835-4Suche in Google Scholar

Lemmon, E.W., Huber, M.L., and McLinden, M.O. (2002). NIST reference fluid thermodynamic and transport properties–REFPROP. NIST Stand. Ref. Database 23: v7.Suche in Google Scholar

Li, G., Zheng, Y., Guo, W., Zhu, D., and Tang, Y. (2020). Mesoscale combustor-powered thermoelectric generator: experimental optimization and evaluation metrics. Appl. Energy 272: 115234, https://doi.org/10.1016/j.apenergy.2020.115234.Suche in Google Scholar

Li, S., Wang, Y., Wang, T., Yang, X., Deng, Y., and Su, C. (2017). Optimization of heat exchangers with dimpled surfaces to improve the performance in thermoelectric generators using a Kriging model. J. Electron. Mater. 46: 3062–3070, https://doi.org/10.1007/s11664-016-5155-4.Suche in Google Scholar

Liu, S., Jin, H., Song, K., Wang, L., Wu, X., and Wang, L. (2017). Heat transfer and pressure drop characteristics of the tube bank fin heat exchanger with fin punched with flow redistributors and curved triangular vortex generators. Heat Mass Tran. 53: 3013–3026, https://doi.org/10.1007/s00231-017-2044-1.Suche in Google Scholar

Lotfi, B. and Sundén, B. (2020). Thermo-hydraulic performance enhancement of finned elliptical tube heat exchangers by utilizing innovative dimple turbulators. Heat Tran. Eng. 41: 1117–1142, https://doi.org/10.1080/01457632.2019.1611132.Suche in Google Scholar

Luo, D., Wang, R., Yu, W., and Zhou, W. (2020). Performance optimization of a converging thermoelectric generator system via multiphysics simulations. Energy 204: 117974, https://doi.org/10.1016/j.energy.2020.117974.Suche in Google Scholar

McBrien, M., Serrenho, A.C., and Allwood, J.M. (2016). Potential for energy savings by heat recovery in an integrated steel supply chain. Appl. Therm. Eng. 103: 592–606, https://doi.org/10.1016/j.applthermaleng.2016.04.099.Suche in Google Scholar

Mohammed Hussein, H.A., Zulkifli, R., Mahmood, W.M.F.B.W., and Ajeel, R.K. (2022). Structure parameters and designs and their impact on performance of different heat exchangers: a review. Renew. Sustain. Energy Rev. 154: 111842, https://doi.org/10.1016/j.rser.2021.111759.Suche in Google Scholar

Motal, R. (2012). Commercialization considerations for gas conversion technology development. In: ARPA-E natural gas conversion technologies workshop. Chevron U.S.A. Inc., Texas.Suche in Google Scholar

Niroomand, R., Saidi, M.H., and Hannani, S.K. (2019). A quasi-three-dimensional thermal model for multi-stream plate fin heat exchangers. Appl. Therm. Eng. 157: 113730, https://doi.org/10.1016/j.applthermaleng.2019.113730.Suche in Google Scholar

Ozturk, M.M., Doğan, B., and Erbay, L.B. (2019). Performance analysis of a compact heat exchanger with offset strip fin by non-uniform uninterrupted fin length. Appl. Therm. Eng. 159: 113814, https://doi.org/10.1016/j.applthermaleng.2019.113814.Suche in Google Scholar

Pacio, J.C. and Dorao, C.A. (2011). A review on heat exchanger thermal hydraulic models for cryogenic applications. Cryogenics 51: 366–379, https://doi.org/10.1016/j.cryogenics.2011.04.005.Suche in Google Scholar

Peng, X., Li, D., Li, J., Jiang, S., and Gao, Q. (2020). Improvement of flow distribution by new inlet header configuration with splitter plates for plate-fin heat exchanger. Energies 13: 1323, https://doi.org/10.3390/en13061323.Suche in Google Scholar

Peng, X., Liu, Z., Qiu, C., and Tan, J. (2014). Passage arrangement design for multi-stream plate-fin heat exchanger under multiple operating conditions. Int. J. Heat Mass Tran. 77: 1055–1062, https://doi.org/10.1016/j.ijheatmasstransfer.2014.06.058.Suche in Google Scholar

Picon-Nunez, M., Polley, G.T., and Medina-Flores, M. (2002). Thermal design of multi-stream heat exchangers. Appl. Therm. Eng. 22: 1643–1660, https://doi.org/10.1016/s1359-4311(02)00074-1.Suche in Google Scholar

Popov, D., Fikiin, K., Stankov, B., Alvarez, G., Youbi-Idrissi, M., Damas, A., Evans, J., and Brown, T. (2019). Cryogenic heat exchangers for process cooling and renewable energy storage: a review. Appl. Therm. Eng. 153: 275–290, https://doi.org/10.1016/j.applthermaleng.2019.02.106.Suche in Google Scholar

Promvonge, P. and Skullong, S. (2021). Enhanced thermal performance in tubular heat exchanger contained with V-shaped baffles. Appl. Therm. Eng. 185: 116307, https://doi.org/10.1016/j.applthermaleng.2020.116307.Suche in Google Scholar

Ramachandra, K.S., Manjunatha, S.S., and Seetharamu, K.N. (2020). Performance analysis of plate-fin heat exchanger used for case drain oil cooling application in variable displacement pumps. J. Phys. Conf. 1473: 012022, https://doi.org/10.1088/1742-6596/1473/1/012022.Suche in Google Scholar

Ramírez, R., Gutiérrez, A.S., Eras, J.J.C., Valencia, K., Hernández, B., and Forero, J.D. (2019). Evaluation of the energy recovery potential of thermoelectric generators in diesel engines. J. Clean. Prod. 241: 118412.10.1016/j.jclepro.2019.118412Suche in Google Scholar

Raul, A., Bhasme, B.N., and Maurya, R.S. (2016). A numerical investigation of fluid flow maldistribution in inlet header configuration of plate fin heat exchanger. Energy Proc. 90: 267–275, https://doi.org/10.1016/j.egypro.2016.11.194.Suche in Google Scholar

Sahoo, M. (2015). Experimental and numerical studies on plate fin heat exchanger, Doctoral dissertation. India, EPrints LogoNIT Rourkela.Suche in Google Scholar

Sarangi, S.K., Mishra, D.P., and Mishra, P. (2020). Parametric investigation of wavy rectangular winglets for heat transfer enhancement in a fin-and–tube heat transfer surface. J. Appl. Fluid Mech. 13: 615–628, https://doi.org/10.29252/jafm.13.02.30545.Suche in Google Scholar

Sarfraz, O., Bach, C.K., and Bradshaw, C. (2018). A literature review of numerical modeling techniques for vapor compression systems with focus on heat exchanger modeling. Oklahoma State University, USA.Suche in Google Scholar

Shu, G., Ma, X., Tian, H., Yang, H., Chen, T., and Li, X. (2018). Configuration optimization of the segmented modules in an exhaust-based thermoelectric generator for engine waste heat recovery. Energy 160: 612–624, https://doi.org/10.1016/j.energy.2018.06.175.Suche in Google Scholar

Skaugen, G., Kolsaker, K., Walnum, H.T., and Wilhelmsen, Ø. (2013). A flexible and robust modelling framework for multi-stream heat exchangers. Comput. Chem. Eng. 49: 95–104, https://doi.org/10.1016/j.compchemeng.2012.10.006.Suche in Google Scholar

Su, C.Q., Huang, C., Deng, Y.D., Wang, Y.P., Chu, P.Q., and Zheng, S.J. (2016). Simulation and optimization of the heat exchanger for automotive exhaust-based thermoelectric generators. J. Electron. Mater. 45: 1464–1472, https://doi.org/10.1007/s11664-015-4077-x.Suche in Google Scholar

Sun, H., Hu, H., Ding, G., Chen, H., Zhang, Z., Wu, C., and Wang, L. (2019). A general distributed-parameter model for thermal performance of cold box with parallel plate-fin heat exchangers based on graph theory. Appl. Therm. Eng. 148: 478–490, https://doi.org/10.1016/j.applthermaleng.2018.11.054.Suche in Google Scholar

Tan, Y., Nookuea, W., Li, H., Thorin, E., and Yan, J. (2017). Property impacts on plate-fin multi-stream heat exchanger (cold box) design in CO2 cryogenic process: part I. Heat exchanger modeling and sensitivity study. Energy Proc. 105: 4587–4594, https://doi.org/10.1016/j.egypro.2017.03.990.Suche in Google Scholar

Taufiq, A. and Dhakar, P.S. (2020). A review study thermal behaviour of plate heat exchanger with various modifications in design. Journal of Emerging Technologies and Innovative Research, India.Suche in Google Scholar

Wang, Y., Li, S., Xie, X., Deng, Y., Liu, X., and Su, C. (2018). Performance evaluation of an automotive thermoelectric generator with inserted fins or dimpled-surface hot heat exchanger. Appl. Energy 218: 391–401, https://doi.org/10.1016/j.apenergy.2018.02.176.Suche in Google Scholar

Wang, Y., Li, S., Yang, X., Deng, Y., and Su, C. (2016). Numerical and experimental investigation for heat transfer enhancement by dimpled surface heat exchanger in thermoelectric generator. J. Electron. Mater. 45: 1792–1802, https://doi.org/10.1007/s11664-015-4228-0.Suche in Google Scholar

Watson, H.A. and Barton, P.I. (2016). Simulation and design methods for multiphase multistream heat exchangers. IFAC-PapersOnLine 49: 839–844, https://doi.org/10.1016/j.ifacol.2016.07.294.Suche in Google Scholar

Yan, S.R., Moria, H., Asaadi, S., Dizaji, H.S., Khalilarya, S., and Jermsittiparsert, K. (2020). Performance and profit analysis of thermoelectric power generators mounted on channels with different cross-sectional shapes. Appl. Therm. Eng. 176: 115455, https://doi.org/10.1016/j.applthermaleng.2020.115455.Suche in Google Scholar

Yang, H., Wen, J., Gu, X., Liu, Y., Wang, S., Cai, W., and Li, Y. (2017). A mathematical model for flow maldistribution study in a parallel plate-fin heat exchanger. Appl. Therm. Eng. 121: 462–472, https://doi.org/10.1016/j.applthermaleng.2017.03.130.Suche in Google Scholar

Young, R., Elliott, R.N., and Kushler, M. (2012). Saving money and reducing risk: how energy efficiency enhances the benefits of the natural gas boom. American Council for an Energy-Efficient Economy, Washington.Suche in Google Scholar

Zhang, B., Fan, G., Yang, J., Liu, C., and Tang, S. (2016). Numerical analysis of header structure improvement in a plate-fin heat exchanger. Chem. Eng. Technol. 39: 1813–1820, https://doi.org/10.1002/ceat.201500728.Suche in Google Scholar

Zhang, L., Yan, X., Zhang, Y., Feng, Y., Li, Y., Meng, H., Zhang, J., and Wu, J. (2020). Heat transfer enhancement by streamlined winglet pair vortex generators for helical channel with rectangular cross section. Chem. Eng. Process. Process Intensif. 147: 107788, https://doi.org/10.1016/j.cep.2019.107788.Suche in Google Scholar
Received: 2022-12-07
Published Online: 2023-06-02
Published in Print: 2023-08-28

© 2023 Walter de Gruyter GmbH, Berlin/Boston

Artikel in diesem Heft

  1. Frontmatter
  2. An approach for an extension of the deflagration model in containment code system COCOSYS to separate burned and unburned atmosphere via junctions
  3. Neutronic analysis of the European sodium cooled fast reactor with Monte Carlo code OpenMC
  4. Identification and tracing of radionuclides in low- and medium-activity liquid radwaste sources of G.A. Siwabessy reactor
  5. Performance evaluation of a currently in-use dry storage cask design for spent accident tolerant fuel loading case under normal operation condition
  6. Optimization of divertor design for Pakistan spherical tokamak
  7. Role of impurity and thermal noise on the radiation sources in ITER using DT fuel
  8. An investigation of multistream plate-fin heat exchanger modelling and design: a review
  9. Ensuring safety of new, advanced small modular reactors for fundamental safety and with an optimal main heat transport systems configuration
  10. Study on calculation model and risk area of radionuclide diffusion in coastal waters under nuclear leakage accidents with different levels
  11. Optimization of 200 MWt HTGR with ThUN-based fuel and zirconium carbide TRISO layer
  12. Experimental study on boiling heat transfer of γ-Fe2O3 nanofluids on a downward heated surface
  13. Evaluating the influence of radial power heterogeneity of fuel rod on its temperature in an accelerator driven subcritical system
  14. Heat transfer enhancement of heat exchanger using rectangular channel with cavities
  15. Calendar of events
https://doi.org/10.1515/kern-2022-0119
Schlagwörter für diesen Artikel
design; heat exchanger; heat transfer; multi-stream plate-fin heat exchanger (MSPFHE); plate-fin heat exchanger (PFHE)

Artikel in diesem Heft

  1. Frontmatter
  2. An approach for an extension of the deflagration model in containment code system COCOSYS to separate burned and unburned atmosphere via junctions
  3. Neutronic analysis of the European sodium cooled fast reactor with Monte Carlo code OpenMC
  4. Identification and tracing of radionuclides in low- and medium-activity liquid radwaste sources of G.A. Siwabessy reactor
  5. Performance evaluation of a currently in-use dry storage cask design for spent accident tolerant fuel loading case under normal operation condition
  6. Optimization of divertor design for Pakistan spherical tokamak
  7. Role of impurity and thermal noise on the radiation sources in ITER using DT fuel
  8. An investigation of multistream plate-fin heat exchanger modelling and design: a review
  9. Ensuring safety of new, advanced small modular reactors for fundamental safety and with an optimal main heat transport systems configuration
  10. Study on calculation model and risk area of radionuclide diffusion in coastal waters under nuclear leakage accidents with different levels
  11. Optimization of 200 MWt HTGR with ThUN-based fuel and zirconium carbide TRISO layer
  12. Experimental study on boiling heat transfer of γ-Fe2O3 nanofluids on a downward heated surface
  13. Evaluating the influence of radial power heterogeneity of fuel rod on its temperature in an accelerator driven subcritical system
  14. Heat transfer enhancement of heat exchanger using rectangular channel with cavities
  15. Calendar of events
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 11.12.2025 von https://www.degruyterbrill.com/document/doi/10.1515/kern-2022-0119/html
Button zum nach oben scrollen