Structuring step dependent characteristics in joining using pin-like structures in the vibration welding process
-
Michael Wolf
und
Dietmar Drummer
Abstract
With this study, correlations in the structuring step of pin-like joining were derived. Increased friction energy due to higher amplitude or force leads to a reduction in structuring time. Changes in thermo-mechanical properties for humid specimens result in increased process times. The theoretical geometry of the pin-like structures is well reproduced in the lower pin area, regardless of the process control. In the upper pin area, increased force and amplitude results in increased defects and air inclusions as a result of an accelerate and more inhomogeneous pin formation. Humidity does not affect the general pin geometry, but should be avoided due to increased air inclusions that can weaken the structure. For the multi-material joints, high bond strengths of up to 30 % of the base material (max. 50 % possible with the geometry used) can be achieved. Therefore, a minimum undercut is required. Once this is reached, the pin defects and the corresponding pin-foot ratio are decisive for the resulting bond quality.
Acknowledgments
The authors thank the German Research Foundation (DFG) for funding this study within the project DFG-432470536 “Joining by using pin-like structures in welding processes”. Further, the authors would like to thank the BASF AG, the Evonik Industries AG, and the Sabic Europe B.V. for providing the used materials.
-
Research ethics: Not applicable.
-
Author contributions: The authors have accepted responsibility for the entire content of this manuscript and approved its submission.
-
Competing interests: The authors state no conflict of interest.
-
Research funding: German Research Foundation (DFG), DFG-432470536 “Joining by using pin-like structures in welding processes.
-
Data availability: The raw data can be obtained on request from the corresponding author.
References
Bates, P.J., Kontopoulou, M., Sidiropoulos, V., Park, G., and Zou, X. (2003). Real time temperature measurement of nylon 66 butt-joints during vibration welding. In: Annual Technical Conference – ANTEC, conference proceedings, pp. 1073–1077.Suche in Google Scholar
Baur, E., Drummer, D., Osswald, T., and Rudolph, N. (2022). Saechtling Kunststoff-Handbuch, 32nd ed. Hanser, München.10.3139/9783446473614.fmSuche in Google Scholar
DIN (1977). Schweißen; Schweißen von Kunststoffen, Verfahren. Beuth-Verlag, Berlin.Suche in Google Scholar
DIN (2008). Kunststoffe – Normalklimate für Konditionierung und Prüfung. Beuth-Verlag, Berlin.Suche in Google Scholar
DIN (2019). Kunststoffe – Polyamide – Beschleunigte Konditionierung von Probekörpern. Beuth-Verlag, Berlin.Suche in Google Scholar
Ehrenstein, G.W. (2001). Polymeric materials. Hanser, München.10.3139/9783446434134.fmSuche in Google Scholar
Ehrenstein, G.W. (2004). Handbuch Kunststoff-Verbindungstechnik. Hanser, München.Suche in Google Scholar
Grewell, D.A., Benatar, A., and Park, J. (2003). Plastics and composites welding handbook. Hanser, München.Suche in Google Scholar
Haq, M., Koricho, E., Khomenko, A., Gerth, R., and Drzahl, L. (2019). Tailorable adhesives for multi-material joining, facile repair and re-assembly. In: Proceedings of the American society for composites.10.2172/1497730Suche in Google Scholar
Hopmann, C. and Michaeli, W. (2017). Einführung in die Kunststoffverarbeitung. Hanser, München.10.3139/9783446453562.fmSuche in Google Scholar
Jaeger, A. (1991). Kombinationen potenzieren das Leistungsvermögen – trends, Tendenzen und Perspektiven beim Mehrkomponenten-Spritzgießen. Kunststoffe 10: 91–94.Suche in Google Scholar
Malnati, P. (2018). Reversible multi-material adhesive bonds. Compos. World: 24–27.Suche in Google Scholar
Meschut, G., Merklein, M., Brosius, A., Drummer, D., Fratini, L., Füssel, U., Gude, M., Homberg, W., Martins, P., Bobbert, M., et al.. (2022). Review on mechanical joining by plastic deformation. J. Adv. Joining Processes 5: 100113, https://doi.org/10.1016/j.jajp.2022.100113.Suche in Google Scholar
Mori, K., Bay, N., Fratini, L., Micari, F., and Tekkaya, A.E. (2013). Joining by plastic deformation. CIRP Ann. 62: 673–694, https://doi.org/10.1016/j.cirp.2013.05.004.Suche in Google Scholar
Niessner, N. (Ed.) (2021). Recycling of plastics. Hanser Publications, Cincinnati, Ohio.10.3139/9781569908570.fmSuche in Google Scholar
Pal, K., Panwar, V., Friedrich, S., and Gehde, M. (2015). An investigation on vibration welding of amorphous and semicrystalline polymers. Mater. Manuf. Processes 31: 372–378, https://doi.org/10.1080/10426914.2015.1019111.Suche in Google Scholar
Patham, B. and Foss, P.H. (2011). Thermoplastic vibration welding. Review of process phenomenology and processing-structure-property interrelationships. Polym. Eng. Sci. 51: 1–22, https://doi.org/10.1002/pen.21784.Suche in Google Scholar
Perrin, H., Bodaghi, M., Berthé, V., Klein, S., and Vaudemont, R. (2023). On the hot-plate welding of reactively compatibilized acrylic-based composites/polyamide (PA)-12. Materials 16: 691, https://doi.org/10.3390/ma16020691.Suche in Google Scholar PubMed PubMed Central
Rotheiser, J. (1999). Joining of plastics – handbook for designers and engineers. Hanser, München.Suche in Google Scholar
Schuster, M. and Stroka, M. (2015). Joining technologies for multi-material-design. In: 15th Stuttgart In-ternational symposium automotive and engine technology 2015. Springer Vieweg.10.1007/978-3-658-08844-6_27Suche in Google Scholar
Stokes, V.K. (1988a). Vibration welding of thermoplastics. Part I: phenomenology of the welding process. Polym. Eng. Sci. 28: 718–727, https://doi.org/10.1002/pen.760281104.Suche in Google Scholar
Stokes, V.K. (1988b). Vibration welding of thermoplastics. Part II: analysis of the welding process. Polym. Eng. Sci. 28: 728–739, https://doi.org/10.1002/pen.760281105.Suche in Google Scholar
Stokes, V.K. (1989). Joining methods for plastics and plastic composites: an overview. Polym. Eng. Sci. 29: 1310–1324, https://doi.org/10.1002/pen.760291903.Suche in Google Scholar
Westkämper, E. and Löffler, C. (2016). Strategien der Produktion -Technologien, Konzepte und Wege in die Praxis. Springer, Berlin, Heidelberg.10.1007/978-3-662-48914-7Suche in Google Scholar
Wolf, M. and Drummer, D. (2020). Influence of the structuring-tool geometry on form-fit joining by use of pin-like structures in vibration welding. Procedia Manuf. 47: 375–382, https://doi.org/10.1016/j.promfg.2020.04.292.Suche in Google Scholar
Wolf, M. and Drummer, D. (2021). Design criteria for the pin-foot ratio for joining adhesion-incompatible polymers using pin-like structures in vibration welding process. J. Polym. Eng. 41: 873–882, https://doi.org/10.1515/polyeng-2021-0199.Suche in Google Scholar
Wolf, M. and Drummer, D. (2022a). Filling behavior in joining using pin-like structures. Polymers 14: 3083, https://doi.org/10.3390/polym14153083.Suche in Google Scholar PubMed PubMed Central
Wolf, M. and Drummer, D. (2022b). Separation of multi-material polymer combinations produced by joining using pin-like structures. J. Manuf. Mater. Process. 6: 13, https://doi.org/10.3390/jmmp6010013.Suche in Google Scholar
Wolf, M. and Drummer, D. (2023a). Deformation of pin-like structures in the joining process in order to produce form-fit multimaterial joints. Joining Plast. – Fügen von Kunststoffen 17: 174–181.Suche in Google Scholar
Wolf, M. and Drummer, D. (2023b). Structure formation in pin-like joining using vibration welding technology. J. Adv. Joining Processes 8: 100158, https://doi.org/10.1016/j.jajp.2023.100158.Suche in Google Scholar
Wolf, M., Kleffel, T., Leisen, C., and Drummer, D. (2017). Joining of incompatible polymer combinations by form fit using the vibration welding process. Int. J. Polym. Sci. 2017, https://doi.org/10.1155/2017/6809469.Suche in Google Scholar
Wolf, M., Hertle, S., and Drummer, D. (2019). Influence of the thermomechanical properties on the joining of adhesion incompatible polymers by form-fit using the vibration welding process. eXPRESS Polym. Lett. 13: 365–378, https://doi.org/10.3144/expresspolymlett.2019.30.Suche in Google Scholar
© 2023 Walter de Gruyter GmbH, Berlin/Boston
Artikel in diesem Heft
- Frontmatter
- Research Articles
- Investigation of the effects of water uptake on the mechanical properties of wood dust particle filled Prosopis Juliflora reinforced phenol formaldehyde hybrid polymer composites
- Experimental investigation on mechanical and tribological analysis of pineapple leaf (Ananas comosus) and sisal (Agave sisalana) fibers reinforced hybrid epoxy composites
- An experimental study of weave pattern effect on the mechanical and dynamic behavior of composite laminates
- Structuring step dependent characteristics in joining using pin-like structures in the vibration welding process
- Fabrication of expandable graphite and soybean oil-based synergistic modified polyurethane foam with improved thermal stability and flame retardant properties
- Fabrication of electrospun nanofiber from a blend of PVC and PHB
- Investigation of mechanical and tribological performance of wood dust reinforced epoxy composite under dry, wet and heated contact condition
- Multi-layer co-extrusion blow molding
- Predicting part quality early during an injection molding cycle
- Optimizing laser-based micro-cutting for PMMA microfluidic device fabrication: thermal analysis and parameter optimization
- Preparation of PVDF/PVA composite films with micropatterned structures on light-cured 3D printed molds for hydrophilic modification of PVDF
- Evaluation of thermal contact resistance of molten resin–mold interface during high-thermal-conductivity polyphenylene sulfide filling in injection molding
- Effect of sinusoidal pulsating speed enhancement on the mixing performance of plastics machinery
- Experimental investigation on the mechanical and wear behavior of epoxy/Indian almond/peepal hybrid composites
- Exploration of the thermal and mechanical characteristics of polymethyl methacrylate-based copolymers: implications for wind turbine blades applications
Artikel in diesem Heft
- Frontmatter
- Research Articles
- Investigation of the effects of water uptake on the mechanical properties of wood dust particle filled Prosopis Juliflora reinforced phenol formaldehyde hybrid polymer composites
- Experimental investigation on mechanical and tribological analysis of pineapple leaf (Ananas comosus) and sisal (Agave sisalana) fibers reinforced hybrid epoxy composites
- An experimental study of weave pattern effect on the mechanical and dynamic behavior of composite laminates
- Structuring step dependent characteristics in joining using pin-like structures in the vibration welding process
- Fabrication of expandable graphite and soybean oil-based synergistic modified polyurethane foam with improved thermal stability and flame retardant properties
- Fabrication of electrospun nanofiber from a blend of PVC and PHB
- Investigation of mechanical and tribological performance of wood dust reinforced epoxy composite under dry, wet and heated contact condition
- Multi-layer co-extrusion blow molding
- Predicting part quality early during an injection molding cycle
- Optimizing laser-based micro-cutting for PMMA microfluidic device fabrication: thermal analysis and parameter optimization
- Preparation of PVDF/PVA composite films with micropatterned structures on light-cured 3D printed molds for hydrophilic modification of PVDF
- Evaluation of thermal contact resistance of molten resin–mold interface during high-thermal-conductivity polyphenylene sulfide filling in injection molding
- Effect of sinusoidal pulsating speed enhancement on the mixing performance of plastics machinery
- Experimental investigation on the mechanical and wear behavior of epoxy/Indian almond/peepal hybrid composites
- Exploration of the thermal and mechanical characteristics of polymethyl methacrylate-based copolymers: implications for wind turbine blades applications
