Artikel
Open Access
High Temperature Corrosion Problem of Boiler Components in presence of Sulfur and Alkali based Fuels
-
Debashis Ghosh
und
Swapan Kumar Mitra
Veröffentlicht/Copyright:
19. April 2011
Received: 2010-08-23
Accepted: 2010-09-15
Published Online: 2011-04-19
Published in Print: 2011-April
Copyright © 2011 De Gruyter
Artikel in diesem Heft
- Editorial
- Thermodynamic Modeling of Zinc Speciation in Electric Arc Furnace Dust
- Removal Rate of Phosphorus from Molten Silicon
- A Feasibility Study on Low Temperature Thermochemical Treatments of Austenitic Stainless Steel in Fluidized Bed Furnace
- Effects of Density Profile and Hot Press Diagram on the Some Technological Properties of Particleboard Composite
- Effects of Heat Treatment on the Microstructure and Mechanical Properties of Low-carbon Microalloyed Steels
- High Temperature Oxidation Behavior of P91, P92 and E911 Alloy Steels in Dry andWet Atmospheres
- Development of Magnesium Powder Metallurgy AZ31 Alloy Using Commercially Available Powders
- Complex Flow Stress Model for a Magnesium Alloy AZ31 at Hot Forming
- Electrochemical-Impedance-Spectroscopy Study of Corrosion of the Alloy NF616 with Molten ZnCl2-KCl Coating in Air at 673 K
- Optical and Thermal Behaviors of Polyamide-Layered Silicate Nanocomposites Based on 4,4′-Azodibenzoic Acid by Solution Intercalation Technique
- High Temperature Corrosion Problem of Boiler Components in presence of Sulfur and Alkali based Fuels
- Pin-On-Disc Characterization of Brass/Ferritic and Pearlitic Ductile Iron Rubbing Pair
- Formation of Alumina Layer on Fe-Cr-Ni Alloy by Pack Cementation and Oxidation
- The Production of Cracks Evolution in Continuously Cast Steel Slab
- In-Situ Oxide Stabilization Development of Aluminum Foams in Powder Metallurgical Route
- Effect of Elevated Temperatures on Behavior of Structural Steel 50CrMo4
- Structural Analysis of Dispersion Strengthened Al-Al4C3 Material by XRD Method
- Mechanical and Electrical Properties of Alloys and Isothermal Section of Ternary Cu-In-Sb System at 673 K
- Thermal and Optical Properties of New Poly(amide-imide)/Nanocomposite Reinforced by Layer Silicate Containing Diphenyl Ether Moieties
- Evolution of Hydrocarbons Ignition Delay Time Over HTAC (High Temperature Air Combustion) Conditions
- High-Temperature Tensile Creep Behavior of A [001] Orientation Single Crystal Nickel-Base Superalloy
- Laser Powder Welding of a Ti52Al46.8Cr1Si0.2Titanium Aluminide Alloy at Elevated Temperature
- A Comparative Study of the Corrosion Behavior of Three Stainless Steels in an Eutectic (Li,Na,K)2CO3 Melt with and without (Na,K)Cl Additives at 973K in Air
- The Arsenic Removal From Molten Steel
- Wear Properties of Titanium and Ti6Al4V Titanium Alloy by Mechanical Milling
- Corrosion of Aluminized and Uncoated 9–12% Cr Boiler Steels in Simulated Biomass andWaste Combustion Conditions
- Temperature and Weight Dependence of Free Volumes in Conducting Composite Polymer Using Positron Annihilation Techniques
Schlagwörter für diesen Artikel
Boiler;
high temperature corrosion;
residual life assessment;
water wall;
superheater and reheater
Creative Commons
BY-NC-ND 3.0
Artikel in diesem Heft
- Editorial
- Thermodynamic Modeling of Zinc Speciation in Electric Arc Furnace Dust
- Removal Rate of Phosphorus from Molten Silicon
- A Feasibility Study on Low Temperature Thermochemical Treatments of Austenitic Stainless Steel in Fluidized Bed Furnace
- Effects of Density Profile and Hot Press Diagram on the Some Technological Properties of Particleboard Composite
- Effects of Heat Treatment on the Microstructure and Mechanical Properties of Low-carbon Microalloyed Steels
- High Temperature Oxidation Behavior of P91, P92 and E911 Alloy Steels in Dry andWet Atmospheres
- Development of Magnesium Powder Metallurgy AZ31 Alloy Using Commercially Available Powders
- Complex Flow Stress Model for a Magnesium Alloy AZ31 at Hot Forming
- Electrochemical-Impedance-Spectroscopy Study of Corrosion of the Alloy NF616 with Molten ZnCl2-KCl Coating in Air at 673 K
- Optical and Thermal Behaviors of Polyamide-Layered Silicate Nanocomposites Based on 4,4′-Azodibenzoic Acid by Solution Intercalation Technique
- High Temperature Corrosion Problem of Boiler Components in presence of Sulfur and Alkali based Fuels
- Pin-On-Disc Characterization of Brass/Ferritic and Pearlitic Ductile Iron Rubbing Pair
- Formation of Alumina Layer on Fe-Cr-Ni Alloy by Pack Cementation and Oxidation
- The Production of Cracks Evolution in Continuously Cast Steel Slab
- In-Situ Oxide Stabilization Development of Aluminum Foams in Powder Metallurgical Route
- Effect of Elevated Temperatures on Behavior of Structural Steel 50CrMo4
- Structural Analysis of Dispersion Strengthened Al-Al4C3 Material by XRD Method
- Mechanical and Electrical Properties of Alloys and Isothermal Section of Ternary Cu-In-Sb System at 673 K
- Thermal and Optical Properties of New Poly(amide-imide)/Nanocomposite Reinforced by Layer Silicate Containing Diphenyl Ether Moieties
- Evolution of Hydrocarbons Ignition Delay Time Over HTAC (High Temperature Air Combustion) Conditions
- High-Temperature Tensile Creep Behavior of A [001] Orientation Single Crystal Nickel-Base Superalloy
- Laser Powder Welding of a Ti52Al46.8Cr1Si0.2Titanium Aluminide Alloy at Elevated Temperature
- A Comparative Study of the Corrosion Behavior of Three Stainless Steels in an Eutectic (Li,Na,K)2CO3 Melt with and without (Na,K)Cl Additives at 973K in Air
- The Arsenic Removal From Molten Steel
- Wear Properties of Titanium and Ti6Al4V Titanium Alloy by Mechanical Milling
- Corrosion of Aluminized and Uncoated 9–12% Cr Boiler Steels in Simulated Biomass andWaste Combustion Conditions
- Temperature and Weight Dependence of Free Volumes in Conducting Composite Polymer Using Positron Annihilation Techniques
