Influence of timber moisture content on wave time-of-flight and longitudinal natural frequency in coniferous species for different instruments
-
Daniel F. Llana
,
Roberto D. Martínez
Abstract
Non-destructive techniques (NDTs) are well suited for rapid estimation of timber properties, but NDT results are affected by several factors, the most important of which is the moisture content (MC) of wood. Much of the research in this context was limited to ultrasound measurement of a few wood species, mainly to Norway spruce. The present paper investigates the MC influence on the NDT results obtained by instruments based on ultrasound (two devices), impact stress waves (one device) and longitudinal vibrations (two devices). A hundred large cross-section specimens of four timber species were tested, namely: radiata pine, Scots pine, Salzmann pine and maritime pine. The influence of MC on velocity was found to be stronger below the fiber saturation point (FSP) than above FSP. MC adjustment factors below FSP are proposed for these wood species.
Acknowledgments
Ministerio de Economía y Competitividad [Spanish Ministry of Economy and Competitiveness]. Plan Nacional I+D 2013-2016. Proy.: BIA 2014-55089-P. Plan Nacional I+D+i 2008-2011. Proy.: BIA 2010-18858. The authors would also like to thank Mr. Ramón García Lombardero for his technical support in the Forest Products Department Laboratory of INIA-CIFOR, Spain.
Author contributions: All the authors have accepted responsibility for the entire content of this submitted manuscript and approved submission.
Research funding: None declared.
Employment or leadership: None declared.
Honorarium: None declared.
References
Arriaga, F., Íñiguez-Gonzalez, G., Esteban, M., Divos, F. (2012) Vibration method for grading of large cross-section coniferous timber species. Holzforschung 66:381–387.10.1515/hf.2011.167Suche in Google Scholar
Arriaga, F., Monton, J., Segues, E., Íñiguez-Gonzalez, G. (2014) Determination of the mechanical properties of radiata pine timber by means of longitudinal and transverse vibration methods. Holzforschung 68:299–305.10.1515/hf-2013-0087Suche in Google Scholar
Arriaga, F., Llana, D.F., Esteban, M., Íñiguez-González, G. (2017) Influence of length and sensor positioning on acoustic time-of-flight (ToF) measurement in structural timber. Holzforschung 71:713–723.10.1515/hf-2016-0214Suche in Google Scholar
Biechele, T., Chui, Y.-H., Gong, M. (2011) Comparison of NDE techniques for assessing mechanical properties of unjointed and finger-jointed lumber. Holzforschung 65:397–401.10.1515/hf.2011.038Suche in Google Scholar
Brashaw, B.K., Vatalaro, R.J., Wacker, J.P., Ross, R.J. (2005) Condition assessment of timber bridges. 2. Evaluation of several stress-wave tools. General Technical Report FPL-GTR-160. Madison, WI, USA. 11 p.10.2737/FPL-GTR-160Suche in Google Scholar
Bucur, V. (1980) Modifications des propriétés acoustiques du bois de résonance sous l’effet de sollicitations de longe durée [Resonance wood acoustical properties modified by long-term loading]. Ann. Forest Sci. 37:249–264.10.1051/forest:19800306Suche in Google Scholar
Bucur, V. Acoustics of Wood. 2nd Edition. Springer, Germany, 2006.10.1007/3-540-30594-7Suche in Google Scholar
Casado, M., Acuña, L., Basterra, L.-A., Ramón-Cueto, G., Vecilla, D. (2012) Grading of structural timber of Populus×euramericana clone I-214. Holzforschung 66:633–638.10.1515/hf-2011-0153Suche in Google Scholar
Chevandier, E., Wertheim, G. (1848) Mémoire sur les proprieties mécaniques du bois [Memory of Mechanical Properties of Wood]. Imprimerie de Bachelier, Paris. 135 pp.Suche in Google Scholar
Denzler, J., Weidenhiller, A. (2016) Pre-grading of spruce logs containing frozen and unfrozen water by means of frequency-based nondestructive testing (NDT). Holzforschung 70:79–85.10.1515/hf-2014-0016Suche in Google Scholar
EN 13183-1:2002. Moisture content of a piece of sawn timber. Part 1: Determination by oven dry method. European standard.Suche in Google Scholar
EN 408:2010+A1:2012. Timber structures. Structural timber and glued laminated timber. Determination of some physical and mechanical properties. European standard.Suche in Google Scholar
Gerhards, C.C. (1982) Longitudinal stress waves for lumber stress grading: factors affecting applications: state of the art. Forest Prod. J. 32:20–25.Suche in Google Scholar
Gonçalves, R., Leme, O.A. (2008) Influence of moisture content on longitudinal, radial and tangential ultrasonic velocity for two Brazilian wood species. Wood Fiber Sci. 40:580–586.Suche in Google Scholar
Gonçalves, R., Mansini-Lorensani, R.G., Negreiros, T.O., Bertoldo, C. (2017) Moisture-related adjustment factor to obtain a reference ultrasonic velocity in structural lumber of plantation hardwood. Wood Mater. Sci. Eng. Online published.10.1080/17480272.2017.1313312Suche in Google Scholar
Íñiguez-González, G., Arriaga, F., Esteban, M., Llana, D.F. (2015) Reference conditions and modification factors for the standardization of nondestructive variables used in the evaluation of existing structures. Constr. Build. Mater. 101:1166–1171.10.1016/j.conbuildmat.2015.05.128Suche in Google Scholar
James, W.L. (1961) Internal friction and speed of sound in Douglas-fir. Forest Prod. J. 11:383–390.Suche in Google Scholar
Kang, H., Booker, R.E. (2002) Variation of stress wave velocity with MC and temperature. Wood Sci. Technol. 36:41–54.10.1007/s00226-001-0129-xSuche in Google Scholar
Kollmann, F., Krech, H. (1960) Dynamische Messung der elastischen Holzeigenshaften und der Dämpfung [Dynamic measurement of damping capacity and elastic properties of wood]. Holz Roh Werkst. 18:41–54.10.1007/BF02615616Suche in Google Scholar
Llana, D.F., Iñiguez-González, G., Arriaga, F., Wang, X. (2016) Time-of-flight adjustment procedure for acoustic measurements in structural timber. BioResources 11:3303–3317.10.15376/biores.11.2.3303-3317Suche in Google Scholar
Matthews, B., Zombori, B., Divós, F. (1994) The effect of moisture content and temperature on the stress wave parameters. Proceedings of the 1st European Symposium on Nondestructive Evaluation of Wood. pp. 261–269. Sep. 21–23. Sopron, Hungary.Suche in Google Scholar
Montero, M.J., de la Mata, J., Esteban, M., Hermoso, E. (2015) Influence of moisture content on the wave velocity to estimate the mechanical properties of large cross-section pieces for structural use of Scots pine from Spain. Maderas-Cienc. Tecnol. 17:407–420.10.4067/S0718-221X2015005000038Suche in Google Scholar
Moreno-Chan, J. (2007) Moisture content in radiata pine wood: implications for wood quality and water-stress response. Doctoral thesis. University of Canterbury, School of Forestry, College of Engineering. New Zealand. 203 p. PDF file: http://ir.canterbury.ac.nz/handle/10092/1217.Suche in Google Scholar
Moreno-Chan, J., Walker, J.C., Raymond, C.A. (2010) Effects of moisture content and temperature on acoustic velocity and dynamic MOE of radiata pine sapwood boards. Wood Sci. Technol. 45:609–626.10.1007/s00226-010-0350-6Suche in Google Scholar
Nocetti, M., Brunetti, M., Bacher, M. (2015) Effect of moisture content on the flexural properties and dynamic modulus of elasticity of dimension chestnut timber. Eur. J. Wood Prod. 73:51–60.10.1007/s00107-014-0861-1Suche in Google Scholar
Oliveira, F.G.R., Candian, M., Lucchette, F.F. (2005) Moisture content effect on ultrasonic velocity in Goupia glabra. Mater. Res-Ibero-Am. J. 8:11–14.10.1590/S1516-14392005000100004Suche in Google Scholar
Ozyhar, T., Hering, S., Sanabria, S.J., Niemz, P. (2013) Determining moisture-dependent elastic characteristics of beech wood by means of ultrasonic waves. Wood Sci. Technol. 47:329–341.10.1007/s00226-012-0499-2Suche in Google Scholar
Rodríguez-Liñán, C., Rubio, P. (2000) Evaluación del estado de la madera, en obras de rehabilitación, mediante técnicas de ultrasonidos [Timber assessment in refurbishment works by ultrasound techniques]. Universidad de Sevilla, Sevilla. 165 p.Suche in Google Scholar
Sakai, H., Minamisawa, A., Takagi, K. (1990) Effect of moisture content on ultrasonic velocity and attenuation in woods. Ultrasonics 28:382–385.10.1016/0041-624X(90)90060-2Suche in Google Scholar
Sanabria, S.J., Furrer, R., Neuenschwander, J., Niemz, P., Sennhauser, U. (2011) Air-coupled ultrasound inspection of glued laminated timber. Holzforschung 65:377–387.10.1515/hf.2011.050Suche in Google Scholar
Sandoz, J.L. (1989) Grading of construction timber by ultrasound. Wood Sci. Technol. 23:95–108.10.1007/BF00350611Suche in Google Scholar
Sandoz, J.L. (1991) Nondestructive evaluation of building timber by ultrasound. Proceedings of the 8th International Symposium on Nondestructive Testing of Wood. pp. 131–142. Sep. 23–25. Vancouver, WA, USA.Suche in Google Scholar
Sandoz, J.L. (1993) Moisture content and temperature effect on ultrasound timber grading. Wood Sci. Technol. 27:373–380.10.1007/BF00192223Suche in Google Scholar
Steiger, R., Arnold, M. (2009) Strength grading of Norway spruce structural timber: revisiting property relationships used in EN 338 classification system. Wood Sci. Technol. 43:259–278.10.1007/s00226-008-0221-6Suche in Google Scholar
Unterwieser, H., Schickhofer, G. (2011) Influence of moisture content of wood on sound velocity and dynamic MOE of natural frequency – and ultrasonic runtime measurement. Eur. J. Wood Prod. 69:171–181.10.1007/s00107-010-0417-ySuche in Google Scholar
Wang, X. (2008) Effects of size and moisture content on stress waves E-rating of structural lumber. Proceedings of the 10th World Conference on Timber Engineering (WCTE). pp. 1–8. Jun. 2–5. Miyazaki, Japan.Suche in Google Scholar
Wang, X. (2013) Stress wave E-rating of structural timber – size and moisture content effects. Proceedings of 18th International nondestructive testing and evaluation of wood symposium. pp. 38–46. Sep. 24–27. Madison, WI, USA.Suche in Google Scholar
Xu, H., Wang, L. (2014) Analysis of cold temperature effect on stress wave velocity in green wood. Holzforschung 68:693–698.10.1515/hf-2013-0151Suche in Google Scholar
Yoshihara, H. (2012a) Off-axis Young’s modulus and off-axis shear modulus of wood measured by flexural vibration tests. Holzforschung 66:207–213.10.1515/HF.2011.118Suche in Google Scholar
Yoshihara, H. (2012b) Influence of specimen configuration on the measurement of the off-axis Young’s modulus of wood by vibration tests. Holzforschung 66:485–492.10.1515/hf.2011.182Suche in Google Scholar
©2018 Walter de Gruyter GmbH, Berlin/Boston
Artikel in diesem Heft
- Frontmatter
- Original Articles
- Improved permeability of autohydrolyzed poplar sapwood against sodium hydroxide for CMP production
- Demethylation and other modifications of industrial softwood kraft lignin by laccase-mediators
- Activated carbon fiber from liquefied wood and polyvinyl butyral as an additive for production of flexible all-carbon yarn supercapacitors
- Short Note
- Fire retardancy of graphene oxide/wood composite (GOW) prepared by a vacuum-pulse dipping technique
- Original Articles
- Comparison of physical and thermal properties of various wood-inorganic composites (WICs) derived by the sol-gel process
- Radiata pine wood treatment with a dispersion of aqueous styrene/acrylic acid copolymer
- Density profiles of novel kraft pulp and TMP based foam formed thermal insulation materials observed by X-ray tomography and densitometry
- Influence of timber moisture content on wave time-of-flight and longitudinal natural frequency in coniferous species for different instruments
- Dimensional changes of cell wall and cell lumens upon water sorption revisited. Literature review and mathematical considerations based on the cylindrical model
- Dynamic mechanical analysis (DMA) of waterlogged archaeological wood at room temperature
- Obituary
- Professor Dr. Mikhail Yakovlevich Zarubin
Artikel in diesem Heft
- Frontmatter
- Original Articles
- Improved permeability of autohydrolyzed poplar sapwood against sodium hydroxide for CMP production
- Demethylation and other modifications of industrial softwood kraft lignin by laccase-mediators
- Activated carbon fiber from liquefied wood and polyvinyl butyral as an additive for production of flexible all-carbon yarn supercapacitors
- Short Note
- Fire retardancy of graphene oxide/wood composite (GOW) prepared by a vacuum-pulse dipping technique
- Original Articles
- Comparison of physical and thermal properties of various wood-inorganic composites (WICs) derived by the sol-gel process
- Radiata pine wood treatment with a dispersion of aqueous styrene/acrylic acid copolymer
- Density profiles of novel kraft pulp and TMP based foam formed thermal insulation materials observed by X-ray tomography and densitometry
- Influence of timber moisture content on wave time-of-flight and longitudinal natural frequency in coniferous species for different instruments
- Dimensional changes of cell wall and cell lumens upon water sorption revisited. Literature review and mathematical considerations based on the cylindrical model
- Dynamic mechanical analysis (DMA) of waterlogged archaeological wood at room temperature
- Obituary
- Professor Dr. Mikhail Yakovlevich Zarubin
