Properties of wood chips for thermomechanical pulp (TMP) production as a function of spout angle
-
Lisbeth M. Hellström
,
Per A. Gradin
Abstract
Spruce wood chips were produced under well-controlled conditions in a laboratory wood chipper at spout angles of 30°, 40°, and 50° at a cutting rate of 20 m s-1 and with a nominal chip length of 25 mm. The chips were then refined under thermomechanical pulp (TMP) conditions in a pilot refiner plant. The pulp properties such as freeness, average fiber length, and shives content were determined and evaluated as a function of specific energy consumption. For a first stage refining and for a freeness value of 350 ml, a decrease in specific electrical energy consumption could be achieved by performing the wood chipping at a spout angle of 50° as compared to 30° which is the spout angle commonly used. A patent application regarding this method has been filed and is pending. It is realized that a freeness value is not directly indicative of any quality measure, such as, for example tensile index and light scattering coefficient but the obtained results can be interpreted to be promising. Further studies are needed regarding the impact of the modified chipping process.
©2011 by Walter de Gruyter Berlin Boston
Articles in the same Issue
- Original Papers
- Fundamental understanding of pulp property development under different thermomechanical pulp refining conditions as observed by a new Simons’ staining method and SEM observation of the ultrastructure of fibre surfaces
- Enhancing dewatering of thermo-mechanical pulp (TMP) based papermaking through enzymatic treatment
- Mechanisms of TMP peroxide bleaching using Mg-based alkalis
- Properties of wood chips for thermomechanical pulp (TMP) production as a function of spout angle
- Determination of local material properties of OSB sample by coupling advanced imaging techniques and morphology-based FEM simulation
- Combined bound water and water vapour diffusion of Norway spruce and European beech in and between the principal anatomical directions
- Oxygen plasma-treated enzymatic hydrolysis lignin as a natural binder for manufacturing biocomposites
- Influence of the adhesive formulation on the mechanical properties and bonding performance of polyurethane prepolymers
- Characterizing perpendicular-to-grain compression (C⊥) behavior in wood construction
- Predicting the strength of Populus spp. clones using artificial neural networks and ε-regression support vector machines (ε-rSVM)
- X-ray scattering and microtomography study on the structural changes of never-dried silver birch, European aspen and hybrid aspen during drying
- Equilibrium moisture content (EMC) in Norway spruce during the first and second desorptions
- Fungal degradation of bamboo samples
- qPCR as a tool to study basidiomycete colonization in wooden field stakes
- Meetings
- Meetings
Articles in the same Issue
- Original Papers
- Fundamental understanding of pulp property development under different thermomechanical pulp refining conditions as observed by a new Simons’ staining method and SEM observation of the ultrastructure of fibre surfaces
- Enhancing dewatering of thermo-mechanical pulp (TMP) based papermaking through enzymatic treatment
- Mechanisms of TMP peroxide bleaching using Mg-based alkalis
- Properties of wood chips for thermomechanical pulp (TMP) production as a function of spout angle
- Determination of local material properties of OSB sample by coupling advanced imaging techniques and morphology-based FEM simulation
- Combined bound water and water vapour diffusion of Norway spruce and European beech in and between the principal anatomical directions
- Oxygen plasma-treated enzymatic hydrolysis lignin as a natural binder for manufacturing biocomposites
- Influence of the adhesive formulation on the mechanical properties and bonding performance of polyurethane prepolymers
- Characterizing perpendicular-to-grain compression (C⊥) behavior in wood construction
- Predicting the strength of Populus spp. clones using artificial neural networks and ε-regression support vector machines (ε-rSVM)
- X-ray scattering and microtomography study on the structural changes of never-dried silver birch, European aspen and hybrid aspen during drying
- Equilibrium moisture content (EMC) in Norway spruce during the first and second desorptions
- Fungal degradation of bamboo samples
- qPCR as a tool to study basidiomycete colonization in wooden field stakes
- Meetings
- Meetings
