Home Wrought aluminium–magnesium alloys subjected to SPD processing
Article
Licensed
Unlicensed Requires Authentication

Wrought aluminium–magnesium alloys subjected to SPD processing

  • Przemysław Snopiński , Tomasz Tański , Krzysztof Labisz , Stanislav Rusz , Petr Jonsta and Mariusz Król
Published/Copyright: August 31, 2016
Become an author with De Gruyter Brill
Author Information
International Journal of Materials Research
From the journal International Journal of Materials Research Volume 107 Issue 7

Abstract

The article presents the influence of stationary plastic deformation, using the equal channel angular pressing (ECAP) method, on the structure and properties of an aluminium alloy with 3 % magnesium content. In order to investigate changes in the structure and substructure, light microscopy and transmission electron microscopy were used. The influence of plastic deformation was determined by hardness measurement using the Vickers method. The results of the investigation show that, even after one ECAP, it is possible to decrease grain size to a range of 30 – 70 nm, and increase the mechanical properties by nearly 90 %. It was also found that the additional twist angle of the die has a minor effect on the properties and structure of the investigated alloy.

Keywords: Aluminium; ECAP; Structure; Hardness; Severe plastic deformation.
*Correspondence address, Krzysztof Labisz, Division of Material Processing Technology Management and Computer Techniques in Materials Science, Institute of Engineering Materials and Biomaterials Silesian University of Technology, Konarskiego 18a St., Gliwice 44-100, Poland, Tel.: +48 322372906, E-mail:

References

[1] T.Tański, W.Pakieła, D.Janicki, B.Tomiczek, M.Król: Arch. Met. Mater.61 (2016), in print. 10.1515/amm-2016-0034Search in Google Scholar

[2] T.Tański, P.Snopiński, W.Pakieła, W.Borek, S.Rusz: Arch. Civ. Mech. Eng.16 (2016) 325–334. 10.1016/j.acme.2015.12.004Search in Google Scholar

[3] L.A.Dobrzański, T.Tański, J.Trzaska: Mater. Sci. Forum638 (2010) 1488. 10.4028/www.scientific.net/MSF.638-642.1488Search in Google Scholar

[4] R.Valiev: Int. J. Mater. Res.100 (2009) 757. 10.3139/146.110095.Search in Google Scholar

[5] J.Liu: Mater. Sci. Forum519 (2006) 1233. 10.4028/www.scientific.net/MSF.519-521.1233Search in Google Scholar

[6] W.Miller, L.Zhuang, J.Bottema, A.J.Wittebrood, P.De Smet, A.Haszler, AVieregge: Mater. Sci. Eng.280 (2008) 37. 10.1016/S0921-5093(99)00653-XSearch in Google Scholar

[7] M.Krupinski, L.A.Dobrzanski, J.H.Sokolowski, W.Kasprzak, G.Byczynski: Mater. Sci. Forum539 (2007) 339. 10.4028/www.scientific.net/MSF.539-543.339Search in Google Scholar

[8] R.Holmestad, R.Bjorge, F.Ehlers, M.Torsaeter, C.Marioara, S.Andersen: J. Phys. Conf. Ser.371 (2012) 1. 10.1088/1742-6596/371/1/012015Search in Google Scholar

[9] R.Z.Valiev, R.KIslamgaliev, I.V.Alexandrov: Prog. Mater. Sci.45 (2000) 103. 10.1016/S0079-6425(99)00007-9Search in Google Scholar

[10] R.Z.Valiev, T.G.Langdon: Prog. Mater. Sci.51 (2006) 881. 10.1016/j.pmatsci.2006.02.003Search in Google Scholar

[11] M.J.Starink, A.-M.Zahra: Acta Mater.46 (1998) 3381. 10.1016/S1359-6454(98)00053-6Search in Google Scholar

[12] K.Labisz: Materialwiss. Werkstofftech.45 (2014) 314. 10.1002/mawe.201400231.Search in Google Scholar

[13] T.Tanski: Materialwiss. Werkstofftech.45 (2014) 333. 10.1002/mawe.201400232.Search in Google Scholar

[14] S.Rusz, L.Cizek, M.Salajka, S.Tylsar, J.Kedron, V.Michenka, T.Donic, E.Hadasik, M.Klos: Arch. Metall. Mater.59 (2014) 359. 10.2478/amm-2014-0060Search in Google Scholar

[15] T.Tański, K.Labisz, B.Krupińska, M.Krupiński, M.Król, R.Maniara: J. Therm. Anal. Calorim.123 (2016) 63–74. 10.1007/s10973-015-4871-ySearch in Google Scholar

[16] Y.J.Chen, Y.C.Chai, H.J.Roven, S.S.Gireesh, Y.D.Yu, J.Hjelen: Mater. Sci. Eng. A545 (2012) 139. 10.1016/j.msea.2012.03.012Search in Google Scholar

[17] M.Dinkel, Fl.Pyczak, J.May, H.W.Hoppel, M.Goken: J. Mater. Sci.43 (2008) 7481. 10.1007/s10853-008-2859-8Search in Google Scholar

[18] O.Nijs, B.Holmedal, J.Friis, E.Nes: Mater. Sci. Eng. A483 (2008) 51. 10.1016/j.msea.2006.11.166Search in Google Scholar

[19] D.G.Morris, M.A.Muñoz-Morris: Acta Mater.50 (2002) 4047. 10.1016/S1359-6454(02)00203-3Search in Google Scholar

[20] M.A.Muñoz-Morris, C.Garcia Oca, G.Gonzalez-Doncel, D.G.Morris: Mater. Sci. Eng. A375 (2004) 853. 10.1016/j.msea.2003.10.141Search in Google Scholar

[21] M.A.Munoz-Morris, C.Garcia Oca, D.G.Morris: Scr. Mater.48 (2003) 213. 10.1016/S1359-6462(02)00501-8Search in Google Scholar

[22] V.Sklenička, J.Dvořák, P.Král, M.Svoboda, I.Saxl: Int. J. Mater. Res.100 (2009) 762. 10.3139/146.110094.Search in Google Scholar

[23] H.Feufel, T.Gödecke, H.L.Lukas, F.Sommer: J. Alloys Compd.247 (1997) 31–42. 10.1016/S0925-8388(96)02655-2Search in Google Scholar

Received: 2015-07-14
Accepted: 2016-03-17
Published Online: 2016-08-31
Published in Print: 2016-07-14

© 2016, Carl Hanser Verlag, München

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. Interdiffusion in bcc_B2 Ni–Al–Cu alloys at 1 173 K
  5. Hydrogen storage kinetics of nanocrystalline and amorphous NdMg12-type alloy–Ni composites synthesized by mechanical milling
  6. Phase equilibria in the Au–Bi–Sn ternary system at temperatures of 80, 125, and 150 °C
  7. Microhardness of decorative gold coatings obtained from gold complex based on mercaptotriazole: Comparison with cyanide
  8. Friction and wear of diamond-like carbon film deposited on CoCrMo alloy under different lubrication
  9. Wrought aluminium–magnesium alloys subjected to SPD processing
  10. Relationships between mechanical and tribological properties of Zn-15Al-based ternary and quaternary alloys
  11. Gel-casting of porous alumina ceramics with high mechanical strength
  12. Comparing predictions from constitutive equations and artificial neural network model of compressive behavior in carbon nanotube–aluminum reinforced ZA27 composites
  13. Identification of the effective thermal conductivity of a powdered composite using a genetic algorithm
  14. Short Communications
  15. Boride coating on the surface of WC–Co-based cemented carbide
  16. People
  17. Prof. Dr. Dr. h. c. mult. Günter Petzow on the occasion of his 90th birthday
  18. DGM News
  19. DGM News
https://doi.org/10.3139/146.111383
Keywords for this article
Aluminium; ECAP; Structure; Hardness; Severe plastic deformation.

Articles in the same Issue

  1. Contents
  2. Contents
  3. Original Contributions
  4. Interdiffusion in bcc_B2 Ni–Al–Cu alloys at 1 173 K
  5. Hydrogen storage kinetics of nanocrystalline and amorphous NdMg12-type alloy–Ni composites synthesized by mechanical milling
  6. Phase equilibria in the Au–Bi–Sn ternary system at temperatures of 80, 125, and 150 °C
  7. Microhardness of decorative gold coatings obtained from gold complex based on mercaptotriazole: Comparison with cyanide
  8. Friction and wear of diamond-like carbon film deposited on CoCrMo alloy under different lubrication
  9. Wrought aluminium–magnesium alloys subjected to SPD processing
  10. Relationships between mechanical and tribological properties of Zn-15Al-based ternary and quaternary alloys
  11. Gel-casting of porous alumina ceramics with high mechanical strength
  12. Comparing predictions from constitutive equations and artificial neural network model of compressive behavior in carbon nanotube–aluminum reinforced ZA27 composites
  13. Identification of the effective thermal conductivity of a powdered composite using a genetic algorithm
  14. Short Communications
  15. Boride coating on the surface of WC–Co-based cemented carbide
  16. People
  17. Prof. Dr. Dr. h. c. mult. Günter Petzow on the occasion of his 90th birthday
  18. DGM News
  19. DGM News
Sign up now to receive a 20% welcome discount
Institutional Access
How does access work?
Have an idea on how to improve our website?
Please write us.
© 2025 De Gruyter Brill
Downloaded on 1.10.2025 from https://www.degruyterbrill.com/document/doi/10.3139/146.111383/html
Scroll to top button