Startseite Low-temperature transformation to bainite in a medium-carbon steel
Artikel
Lizenziert
Nicht lizenziert Erfordert eine Authentifizierung

Low-temperature transformation to bainite in a medium-carbon steel

  • Mathew J. Peet , Hala S. Hasan , Marie-Noëlle Avettand-Fènoël , Saud H. A. Raubye und Harshad K. D. H. Bhadeshia
Veröffentlicht/Copyright: 31. Januar 2017
Veröffentlichen auch Sie bei De Gruyter Brill
Informationen für Autor*innen
International Journal of Materials Research
Aus der Zeitschrift International Journal of Materials Research Band 108 Heft 2

Abstract

The consequences of reducing the carbon concentration from 0.8 to 0.6 wt.% in a bulk nanostructured bainitic-steel have been investigated with the aim of enabling processing. We observed that the average thickness of the product phase plates increased from below 20–40 nm to about 100 nm after isothermal transformation at the same temperature. The increase in plate size led to decrease in hardness as expected. However the hardness reduction was not as large as might be expected, a transition to lower bainite at temperatures below 250°C may have provided additional strengthening. Transformation just below the martensite start temperature resulted in a mixture of martensite and bainite, with no observed increase in the rate of bainite transformation.

Keywords: Hardness; Nanostructure; Bainite; Steel
*Correspondence address, Dr. Mathew J. Peet, University of Cambridge, Materials Science and Metallurgy, 27 Charles Babbage Road, Cambridge, CB3 0FS, United Kingdom, Tel.: +441223334336, E-Mail:

References

[1] F.G.Caballero, H.K.D.H.Bhadeshia, K.J.A.Mawella, D.G.Jones, P.Brown: Mater. Sci. Technol.18 (2002) 279. 10.1179/026708301225000725Suche in Google Scholar

[2] H.K.D.H.Bhadeshia: Sci. Technol. Adv. Mater.14 (2013) 014202. 10.1088/1468-6996/14/1/014202Suche in Google Scholar

[3] H.K.D.H.Bhadeshia: Prog. Mater. Sci.57 (2012) 268. 10.1016/j.pmatsci.2011.06.002Suche in Google Scholar

[4] C.Garcia-Mateo, M.Peet, F.G.Caballero, H.K.D.H.Bhadeshia: Mater. Sci. Technol.20 (2004) 814. 10.1179/026708304225017355Suche in Google Scholar

[5] H.S.Hasan, M.J.Peet, H.K.D.H.Bhadeshia: Int. J. Mater. Res.103 (2012) 1319–1324. 10.3139/146.110788Suche in Google Scholar

[6] K.Fang, J.G.Yang, X.S.Liu, K.J.Song, H.Y.Fang, H.K.D.H.Bhadeshia: Mater. Des.50 (2013) 38–43. 10.1016/j.matdes.2013.02.019Suche in Google Scholar

[7] H.K.D.H.Bhadeshia: Acta Metall. Mater.29 (1981) 1117. 10.1016/0001-6160(81)90063-8Suche in Google Scholar

[8] H.K.D.H.Bhadeshia in: J.M.Howe, D.E.Laughlin, J.K.Lee, U.Dahmen, W.A.Soffa (Eds.), Solid-Solid Phase Transformations, TME-AIME, Vol 1, Warrendale, Pennsylvania, USA, (2005) 469–484.Suche in Google Scholar

[9] H.S.Yang, H.K.D.H.Bhadeshia: Mater. Sci. Technol.24 (2008) 335. 10.1179/174328408X275982Suche in Google Scholar

[10] F.G.Caballero, C.Capdevila, C. Garciade Andrés: Mater. Sci. Technol.18 (2002) 534. 10.1179/026708302225002146Suche in Google Scholar

[11] H.K.D.H.Bhadeshia: Proc. R. Soc. Lond. A466 (2010) 3. 10.1098/rspa.2009.0407Suche in Google Scholar

[12] M.Soliman, H.Palkowski: ISIJ Int.47 (2007) 1703. 10.2355/isijinternational.47.1703Suche in Google Scholar

[13] M.Kundu, S.Ganguly, S.Datta, P.P.Chattopadhyay: Mater. Manuf. Process.24 (2009) 169. 10.1080/10426910802612239Suche in Google Scholar

[14] A.Leiro, A.Kankanala, E.Vuorinen, B.Prakash: Wear273 (2011) 2. 10.1016/j.wear.2011.03.025Suche in Google Scholar

[15] I.Lonardelli, M.Bortolotti, W.van Beek, L.Girardini, M.Zadra, H.K.D.H.Bhadeshia: Mater. Sci. Eng. A555 (2012) 139. 10.1016/j.msea.2012.06.043Suche in Google Scholar

[16] C.G.Mateo, F.G.Caballero: ISIJ Int.45 (2005) 1736. 10.2355/isijinternational.45.1736Suche in Google Scholar

[17] I.Timokhina, H.Beladi, X.Y.Xiong, Y.Adachi, P.Hodsgon: Solid State Phenom.172–174 (2011) 1249. 10.4028/www.scientific.net/SSP.172-174.1249Suche in Google Scholar

[18] H.S.Yang, H.K.D.H.Bhadeshia: Mater. Sci. Technol.23 (2007) 556. 10.1179/174328407X176857Suche in Google Scholar

[19] D.J.Dyson, B.Holmes: J. Iron Steel Int.208 (1970) 469–474.Suche in Google Scholar

[20] H.K.D.H.Bhadeshia, S.A.David, J.M.Vitek, R.W.Reed: Mater. Sci. Technol.7 (1991) 686. 10.1179/mst.1991.7.8.686Suche in Google Scholar

[21] NPL MTDATA Software: National Physical Laboratory, Teddington, U.K., (2006).Suche in Google Scholar

[22] E.Kozeschnik, H.K.D.H.Bhadeshia: Mater. Sci. Technol.24 (2008) 343. 10.1179/174328408X275973Suche in Google Scholar

[23] http://www.msm.cam.ac.uk/map/steel/programs/mucg46-b.htmlSuche in Google Scholar

[24] http://www.msm.cam.ac.uk/map/steel/programs/mucg83.htmlSuche in Google Scholar

[25] M.Peet: Mater. Sci. Technol, 31 (2015) 1370. 10.1179/1743284714Y.0000000714Suche in Google Scholar

[26] H.K.D.H.Bhadeshia: Met. Sci.16 (1982) 159. 10.1179/030634582790427217Suche in Google Scholar

[27] L.C.Chang, H.K.D.H.Bhadeshia: Mater. Sci. Technol.11 (1995) 874. 10.1179/mst.1995.11.9.874Suche in Google Scholar

[28] G.Papadimitriu, G.Fourlaris: J. Phys. IV, 7(C5) (1997) 131. 10.1051/jp4:1997520Suche in Google Scholar

[29] S.B.Singh, H.K.D.H.Bhadeshia: Mater. Sci. Eng. A245 (1998) 72. 10.1016/S0921-5093(97)00701-6Suche in Google Scholar

[30] http://www.msm.cam.ac.uk/phase-trans/2016/mediumC/medium.zipSuche in Google Scholar

[31] C.Garcia-Mateo, F.G.Caballero, H.K.D.H.Bhadeshia: ISIJ. Int.43 (2003) 1238. 10.2355/isijinternational.43.1238Suche in Google Scholar

[32] J.Cornide, G.Garcia-Mateo, C.Capdevila, F.G.Caballero: J. Alloys Compd.577 (2013) S43. 10.1016/j.jallcom.2011.11.066Suche in Google Scholar

[33] W.Solano-Alvarez, H.F.G.Abreu, M.R.da Silva, M.J.Peet: J. Magn. Magn. Mater.378 (2015) 200. 10.1016/j.jmmm.2014.11.037Suche in Google Scholar

[34] J.Daigne, M.Guttmann, J.P.Naylor: Mater. Sci. Eng.56 (1982) 1. 10.1016/0025-5416(82)90176-8Suche in Google Scholar

[35] C.Garcia-Mateo, F.G.Caballero, H.K.D.H.Bhadeshia: ISIJ Int.43 (2003) 1821. 10.2355/isijinternational.43.1821Suche in Google Scholar

[36] M.J.Peet: PhD thesis, University of Cambridge, UK (2010).Suche in Google Scholar

[37] C.H.Young, H.K.D.H.Bhadeshia: J. Phys. IV, 5 (1995) C8–829. 10.1051/jp4:1995837Suche in Google Scholar

[38] D.P.Koistinen, R.E.Marburger: Acta Metall. Mater.7 (1959) 59–60. 10.1016/0001-6160(59)90170-1Suche in Google Scholar

[39] S.Chatterjee, H.K.D.H.Bhadeshia: Mater. Sci. Technol.22 (2006) 645. 10.1179/174328406X86182Suche in Google Scholar

Received: 2016-09-26
Accepted: 2016-11-22
Published Online: 2017-01-31
Published in Print: 2017-02-10

© 2017, Carl Hanser Verlag, München

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Editorial
  4. A new editor for IJMR
  5. Original Contributions
  6. Structural anisotropy in equal-channel angular extruded nickel revealed by dilatometric study of excess volume
  7. Low-temperature transformation to bainite in a medium-carbon steel
  8. Study on the welding continuous cooling transformation and weldability of SA508Gr4 steel for nuclear pressure vessels
  9. Phase precipitation in transition metal-containing 354-type alloys
  10. Effect of laser alloying on heat-treated light alloys
  11. In-situ synthesis, microstructure and properties of Ti2AlN/TiB2 composite
  12. Characterization of mechanical properties of Al/TiCP MMC
  13. Performance evaluation of polysulfone/graphene nanocomposites
  14. Short Communications
  15. Influence of Cu and Mg addition on age-related deterioration in strength and creep behavior of Zn-12Al die casting alloys
  16. Effects of mixing speed of a composite on its friction coefficient and wear resistance
  17. DGM News
  18. DGM News
https://doi.org/10.3139/146.111461
Schlagwörter für diesen Artikel
Hardness; Nanostructure; Bainite; Steel

Artikel in diesem Heft

  1. Contents
  2. Contents
  3. Editorial
  4. A new editor for IJMR
  5. Original Contributions
  6. Structural anisotropy in equal-channel angular extruded nickel revealed by dilatometric study of excess volume
  7. Low-temperature transformation to bainite in a medium-carbon steel
  8. Study on the welding continuous cooling transformation and weldability of SA508Gr4 steel for nuclear pressure vessels
  9. Phase precipitation in transition metal-containing 354-type alloys
  10. Effect of laser alloying on heat-treated light alloys
  11. In-situ synthesis, microstructure and properties of Ti2AlN/TiB2 composite
  12. Characterization of mechanical properties of Al/TiCP MMC
  13. Performance evaluation of polysulfone/graphene nanocomposites
  14. Short Communications
  15. Influence of Cu and Mg addition on age-related deterioration in strength and creep behavior of Zn-12Al die casting alloys
  16. Effects of mixing speed of a composite on its friction coefficient and wear resistance
  17. DGM News
  18. DGM News
Jetzt anmelden und 20% sparen
Institutioneller Zugang
Wie funktioniert Authentifizierung?
Haben Sie eine Idee, wie wir unsere Website verbessern können?
Bitte schreiben Sie uns.
© 2025 De Gruyter Brill
Heruntergeladen am 16.11.2025 von https://www.degruyterbrill.com/document/doi/10.3139/146.111461/html
Button zum nach oben scrollen